OPERATION
Motive Force Control during TRC or VSC Operation
During the TRC or VSC operation, the skid control ECU outputs the motive force control signal to the power management control ECU. Upon receiving this signal, the power management control ECU inhibits the motive force.
Normal Brake Operation (with Regenerative Brake Cooperative Control)
During normal braking, the switching solenoid valves SSC and SCC open and the switching solenoid valves SMC and SRC close, and thus the fluid pressure circuit from the hydraulic brake booster to each wheel cylinder is individually separated. Each of the wheel cylinder pressures can be increased, retained and decreased by controlling the pressure control solenoid valves SLA and SLR under the condition.
The skid control ECU calculates the braking force required by the driver in accordance with the signals received from the master cylinder pressure sensor and the brake pedal stroke sensor. Then, the skid control ECU calculates the regenerative brake force value out of the required brake force and transmits the calculated value to the power management control ECU. Upon receiving the value, the power management control ECU generates a regenerative brake force. At the same time, the power management control ECU transmits the actual regenerative brake force value to the skid control ECU. The skid control ECU controls the solenoid valves in order to cause the hydraulic brake system to generate a brake force value (which is obtained by subtracting the regenerative brake force from the brake force value required by the driver).
The skid control ECU calculates the target wheel cylinder pressure (equivalent to the brake force required by the driver) in accordance with the signals received from the master cylinder pressure sensor and the brake pedal stroke sensor. The skid control ECU compares the wheel cylinder pressure with the target wheel cylinder pressure. If the wheel cylinder pressure is lower than the target wheel cylinder pressure, the skid control ECU boosts the pressure in the brake actuator. Accordingly, the fluid pressure in the accumulator is fed into the wheel cylinder. Moreover, this operation is the same when the hydraulic brake force must be increased in order to effect cooperative control in accordance with the changes in the regenerative brake force.
| *1 | Reservoir Tank | *2 | Brake Fluid Level Warning Switch |
| *3 | Accumulator | *4 | Pump Motor |
| *5 | Pressure Relief Valve | *6 | Hydraulic Brake Booster |
| *7 | Stroke Simulator | *8 | Switching Solenoid Valve SSC |
| *9 | Master Cylinder Pressure Sensor | *10 | Accumulator Pressure Sensor |
| *11 | Switching Solenoid Valve SMC | *12 | Switching Solenoid Valve SRC |
| *13 | Pressure Control Solenoid Valve SLA | *14 | Front Wheel Cylinder Pressure Sensor |
| *15 | Switching Solenoid Valve SCC | *16 | Pressure Control Solenoid Valve SLR |
| *17 | Pressure Holding Solenoid Valve FLH | *18 | Pressure Holding Solenoid Valve FRH |
| *19 | Pressure Holding Solenoid Valve RLH | *20 | Pressure Holding Solenoid Valve RRH |
| *21 | Pressure Reduction Solenoid Valve FLR | *22 | Pressure Reduction Solenoid Valve FRR |
| *23 | Pressure Reduction Solenoid Valve RLR | *24 | Pressure Reduction Solenoid Valve RRR |
| *25 | Front Left Wheel Cylinder | *26 | Front Right Wheel Cylinder |
| *27 | Rear Left Wheel Cylinder | *28 | Rear Right Wheel Cylinder |
| *29 | Brake Actuator | - | - |
| Item | Normal Braking Increase Mode | |
|---|---|---|
| Pressure Control Solenoid Valve | SLA | On (Half-open*) |
| SLR | Off (Close) | |
| Switching Solenoid Valve | SSC | On (Open) |
| SCC | On (Open) | |
| SMC | On (Close) | |
| SRC | On (Close) | |
| Pressure Holding Solenoid Valve | FLH | Off (Open) |
| FRH | Off (Open) | |
| RLH | Off (Open) | |
| RRH | Off (Open) | |
| Pressure Reduction Solenoid Valve | FLR | Off (Close) |
| FRR | Off (Close) | |
| RLR | Off (Close) | |
| RRR | Off (Close) | |
*: The solenoid valve constantly regulates the amount of opening of the valve in accordance with the use conditions in order to control the fluid pressure.
The skid control ECU calculates the target wheel cylinder pressure (equivalent to the brake force required by the driver) in accordance with the signals received from the master cylinder pressure sensor and the brake pedal stroke sensor. The skid control ECU compares the wheel cylinder pressure with the target wheel cylinder pressure. If they are equal, the skid control ECU controls the brake actuator in the hold state. Accordingly, the wheel cylinder will be held at a constant pressure.
| *1 | Reservoir Tank | *2 | Brake Fluid Level Warning Switch |
| *3 | Accumulator | *4 | Pump Motor |
| *5 | Pressure Relief Valve | *6 | Hydraulic Brake Booster |
| *7 | Stroke Simulator | *8 | Switching Solenoid Valve SSC |
| *9 | Master Cylinder Pressure Sensor | *10 | Accumulator Pressure Sensor |
| *11 | Switching Solenoid Valve SMC | *12 | Switching Solenoid Valve SRC |
| *13 | Pressure Control Solenoid Valve SLA | *14 | Front Wheel Cylinder Pressure Sensor |
| *15 | Switching Solenoid Valve SCC | *16 | Pressure Control Solenoid Valve SLR |
| *17 | Pressure Holding Solenoid Valve FLH | *18 | Pressure Holding Solenoid Valve FRH |
| *19 | Pressure Holding Solenoid Valve RLH | *20 | Pressure Holding Solenoid Valve RRH |
| *21 | Pressure Reduction Solenoid Valve FLR | *22 | Pressure Reduction Solenoid Valve FRR |
| *23 | Pressure Reduction Solenoid Valve RLR | *24 | Pressure Reduction Solenoid Valve RRR |
| *25 | Front Left Wheel Cylinder | *26 | Front Right Wheel Cylinder |
| *27 | Rear Left Wheel Cylinder | *28 | Rear Right Wheel Cylinder |
| *29 | Brake Actuator | - | - |
| Item | Normal Braking Holding Mode | |
|---|---|---|
| Pressure Control Solenoid Valve | SLA | Off (Close) |
| SLR | Off (Close) | |
| Switching Solenoid Valve | SSC | On (Open) |
| SCC | On (Open) | |
| SMC | On (Close) | |
| SRC | On (Close) | |
| Pressure Holding Solenoid Valve | FLH | Off (Open) |
| FRH | Off (Open) | |
| RLH | Off (Open) | |
| RRH | Off (Open) | |
| Pressure Reduction Solenoid Valve | FLR | Off (Close) |
| FRR | Off (Close) | |
| RLR | Off (Close) | |
| RRR | Off (Close) | |
The skid control ECU calculates the target wheel cylinder pressure (equivalent to the brake force required by the driver) in accordance with the signals received from the master cylinder pressure sensor and the brake pedal stroke sensor. The skid control ECU compares the wheel cylinder pressure with the target wheel cylinder pressure. If the wheel cylinder pressure is higher than the target wheel cylinder pressure, the skid control ECU reduces the pressure in the brake actuator. Accordingly, the pressure in the wheel cylinder decreases. Moreover, this operation is the same when the hydraulic brake force must be decreased in order to effect cooperative control in accordance with the changes in the regenerative brake force.
| *1 | Reservoir Tank | *2 | Brake Fluid Level Warning Switch |
| *3 | Accumulator | *4 | Pump Motor |
| *5 | Pressure Relief Valve | *6 | Hydraulic Brake Booster |
| *7 | Stroke Simulator | *8 | Switching Solenoid Valve SSC |
| *9 | Master Cylinder Pressure Sensor | *10 | Accumulator Pressure Sensor |
| *11 | Switching Solenoid Valve SMC | *12 | Switching Solenoid Valve SRC |
| *13 | Pressure Control Solenoid Valve SLA | *14 | Front Wheel Cylinder Pressure Sensor |
| *15 | Switching Solenoid Valve SCC | *16 | Pressure Control Solenoid Valve SLR |
| *17 | Pressure Holding Solenoid Valve FLH | *18 | Pressure Holding Solenoid Valve FRH |
| *19 | Pressure Holding Solenoid Valve RLH | *20 | Pressure Holding Solenoid Valve RRH |
| *21 | Pressure Reduction Solenoid Valve FLR | *22 | Pressure Reduction Solenoid Valve FRR |
| *23 | Pressure Reduction Solenoid Valve RLR | *24 | Pressure Reduction Solenoid Valve RRR |
| *25 | Front Left Wheel Cylinder | *26 | Front Right Wheel Cylinder |
| *27 | Rear Left Wheel Cylinder | *28 | Rear Right Wheel Cylinder |
| *29 | Brake Actuator | - | - |
| Item | Normal Braking Reduction Mode | |
|---|---|---|
| Pressure Control Solenoid Valve | SLA | Off (Close) |
| SLR | On (Half-open*) | |
| Switching Solenoid Valve | SSC | On (Open) |
| SCC | On (Open) | |
| SMC | On (Close) | |
| SRC | On (Close) | |
| Pressure Holding Solenoid Valve | FLH | Off (Open) |
| FRH | Off (Open) | |
| RLH | Off (Open) | |
| RRH | Off (Open) | |
| Pressure Reduction Solenoid Valve | FLR | Off (Close) |
| FRR | Off (Close) | |
| RLR | Off (Close) | |
| RRR | Off (Close) | |
*: The solenoid valve constantly regulates the amount of opening of the valve in accordance with the use conditions in order to control the fluid pressure.
ABS with EBD Operation
Based on the signals received from the 4 speed sensors, the skid control ECU calculates each wheel speed and deceleration, and checks wheel slipping conditions. According to the slipping condition, the skid control ECU controls the pressure holding valve and pressure reduction valve in order to adjust the fluid pressure of the each wheel cylinder in the following 3 modes: pressure reduction, pressure holding, and pressure increase modes.
| Not Activated | Normal Braking | - | - |
|---|---|---|---|
| Activated | Increase Mode | Holding Mode | Reduction Mode |
| Pressure Holding Solenoid Valve | OFF (Open) | ON (Close) | ON (Close) |
| Pressure Reduction Solenoid Valve | OFF (Close) | OFF (Close) | ON (Open) |
| Wheel Cylinder Pressure | Increase | Hold | Reduce |
Brake Assist Operation
In the event of emergency braking, the skid control ECU detects the driver's intention based on the speed of the pressure increase in the master cylinder determined by the master cylinder pressure sensor signal. If the skid control ECU judges the need for additional brake assist, the fluid pressure from the accumulator is directed to the wheel cylinder to apply a greater fluid pressure than the regulator.
| *1 | Reservoir Tank | *2 | Brake Fluid Level Warning Switch |
| *3 | Accumulator | *4 | Pump Motor |
| *5 | Pressure Relief Valve | *6 | Hydraulic Brake Booster |
| *7 | Stroke Simulator | *8 | Switching Solenoid Valve SSC |
| *9 | Master Cylinder Pressure Sensor | *10 | Accumulator Pressure Sensor |
| *11 | Switching Solenoid Valve SMC | *12 | Switching Solenoid Valve SRC |
| *13 | Pressure Control Solenoid Valve SLA | *14 | Front Wheel Cylinder Pressure Sensor |
| *15 | Switching Solenoid Valve SCC | *16 | Pressure Control Solenoid Valve SLR |
| *17 | Pressure Holding Solenoid Valve FLH | *18 | Pressure Holding Solenoid Valve FRH |
| *19 | Pressure Holding Solenoid Valve RLH | *20 | Pressure Holding Solenoid Valve RRH |
| *21 | Pressure Reduction Solenoid Valve FLR | *22 | Pressure Reduction Solenoid Valve FRR |
| *23 | Pressure Reduction Solenoid Valve RLR | *24 | Pressure Reduction Solenoid Valve RRR |
| *25 | Front Left Wheel Cylinder | *26 | Front Right Wheel Cylinder |
| *27 | Rear Left Wheel Cylinder | *28 | Rear Right Wheel Cylinder |
| *29 | Brake Actuator | - | - |
| Item | Normal Braking Increase Mode | Brake Assist Activated | |
|---|---|---|---|
| Pressure Control Solenoid Valve | SLA | On (Half-open*) | On (Half-open*) |
| SLR | Off (Close) | Off (Close) | |
| Switching Solenoid Valve | SSC | On (Open) | On (Open) |
| SCC | On (Open) | On (Open) | |
| SMC | On (Close) | On (Close) | |
| SRC | On (Close) | On (Close) | |
| Pressure Holding Solenoid Valve | FLH | Off (Open) | Off (Open) |
| FRH | Off (Open) | Off (Open) | |
| RLH | Off (Open) | Off (Open) | |
| RRH | Off (Open) | Off (Open) | |
| Pressure Reduction Solenoid Valve | FLR | Off (Close) | Off (Close) |
| FRR | Off (Close) | Off (Close) | |
| RLR | Off (Close) | Off (Close) | |
| RRR | Off (Close) | Off (Close) | |
*: The solenoid valve constantly regulates the amount of opening of the valve in accordance with the use conditions in order to control the fluid pressure.
TRC Operation
The fluid pressure stored in the accumulator is regulated by the switching solenoid valves and control solenoid valves to the required pressure. Thus, the wheel cylinders of the drive wheels are controlled in the following 3 modes: pressure reduction, pressure holding, and pressure increase modes to control the slippage of the drive wheels. The diagram below shows the hydraulic circuit in the pressure increase mode when the TRC is activated. The pressure holding solenoid valve and the pressure reduction solenoid valve are turned on/off according to the ABS with EBD operation pattern.
| *1 | Reservoir Tank | *2 | Brake Fluid Level Warning Switch |
| *3 | Accumulator | *4 | Pump Motor |
| *5 | Pressure Relief Valve | *6 | Hydraulic Brake Booster |
| *7 | Stroke Simulator | *8 | Switching Solenoid Valve SSC |
| *9 | Master Cylinder Pressure Sensor | *10 | Accumulator Pressure Sensor |
| *11 | Switching Solenoid Valve SMC | *12 | Switching Solenoid Valve SRC |
| *13 | Pressure Control Solenoid Valve SLA | *14 | Front Wheel Cylinder Pressure Sensor |
| *15 | Switching Solenoid Valve SCC | *16 | Pressure Control Solenoid Valve SLR |
| *17 | Pressure Holding Solenoid Valve FLH | *18 | Pressure Holding Solenoid Valve FRH |
| *19 | Pressure Holding Solenoid Valve RLH | *20 | Pressure Holding Solenoid Valve RRH |
| *21 | Pressure Reduction Solenoid Valve FLR | *22 | Pressure Reduction Solenoid Valve FRR |
| *23 | Pressure Reduction Solenoid Valve RLR | *24 | Pressure Reduction Solenoid Valve RRR |
| *25 | Front Left Wheel Cylinder | *26 | Front Right Wheel Cylinder |
| *27 | Rear Left Wheel Cylinder | *28 | Rear Right Wheel Cylinder |
| *29 | Brake Actuator | - | - |
| Item | TRC not Activated | TRC Activated | |||
|---|---|---|---|---|---|
| Increase Mode | Holding Mode | Reduction Mode | |||
| Pressure Control Solenoid Valve | SLA | Off (Close) | On (Open) | On (Open) | On (Open) |
| SLR | Off (Close) | Off (Close) | Off (Close) | Off (Close) | |
| Switching Solenoid Valve | SSC | On (Open) | On (Open) | On (Open) | On (Open) |
| SCC | On (Open) | On (Open) | On (Open) | On (Open) | |
| SMC | Off (Open) | On (Close) | On (Close) | On (Close) | |
| SRC | Off (Open) | On (Close) | On (Close) | On (Close) | |
| Pressure Holding Solenoid Valve | FLH | Off (Open) | Off (Open) | On (Close) | On (Close) |
| FRH | Off (Open) | Off (Open) | On (Close) | On (Close) | |
| RLH | Off (Open) | On (Close) | On (Close) | On (Close) | |
| RRH | Off (Open) | On (Close) | On (Close) | On (Close) | |
| Pressure Reduction Solenoid Valve | FLR | Off (Close) | Off (Close) | Off (Close) | On (Open) |
| FRR | Off (Close) | Off (Close) | Off (Close) | On (Open) | |
| RLR | Off (Close) | Off (Close) | Off (Close) | Off (Close) | |
| RRR | Off (Close) | Off (Close) | Off (Close) | Off (Close) | |
VSC Operation
The VSC, by way of solenoid valves, controls the fluid pressure that is stored in the accumulator and applies it to the brake wheel cylinder of each wheel in the following 3 modes: pressure reduction, pressure holding, and pressure increase modes. As a result, the tendency to front wheel skid or rear wheel skid is controlled.
In the front wheel skid restraining control, the brakes of the front wheels and rear wheel of the inner circle of the turn is applied. Also, depending on whether the brake is on or off and the condition of the vehicle, there are circumstances in which the brake might not be applied to the wheels even if the wheel is targeted for braking. The diagram below shows the hydraulic circuit in the pressure increase mode, as it controls the front wheel skid condition while the vehicle makes a right turn. In other operating modes, the pressure holding valve and the pressure reduction valve are turned on/off according to the ABS with EBD operation pattern.
| *1 | Reservoir Tank | *2 | Brake Fluid Level Warning Switch |
| *3 | Accumulator | *4 | Pump Motor |
| *5 | Pressure Relief Valve | *6 | Hydraulic Brake Booster |
| *7 | Stroke Simulator | *8 | Switching Solenoid Valve SSC |
| *9 | Master Cylinder Pressure Sensor | *10 | Accumulator Pressure Sensor |
| *11 | Switching Solenoid Valve SMC | *12 | Switching Solenoid Valve SRC |
| *13 | Pressure Control Solenoid Valve SLA | *14 | Front Wheel Cylinder Pressure Sensor |
| *15 | Switching Solenoid Valve SCC | *16 | Pressure Control Solenoid Valve SLR |
| *17 | Pressure Holding Solenoid Valve FLH | *18 | Pressure Holding Solenoid Valve FRH |
| *19 | Pressure Holding Solenoid Valve RLH | *20 | Pressure Holding Solenoid Valve RRH |
| *21 | Pressure Reduction Solenoid Valve FLR | *22 | Pressure Reduction Solenoid Valve FRR |
| *23 | Pressure Reduction Solenoid Valve RLR | *24 | Pressure Reduction Solenoid Valve RRR |
| *25 | Front Left Wheel Cylinder | *26 | Front Right Wheel Cylinder |
| *27 | Rear Left Wheel Cylinder | *28 | Rear Right Wheel Cylinder |
| *29 | Brake Actuator | - | - |
| Item | VSC not Activated | VSC Activated | |||
|---|---|---|---|---|---|
| Increase Mode | Holding Mode | Reduction Mode | |||
| Pressure Control Solenoid Valve | SLA | Off (Close) | On (Open) | On (Open) | On (Open) |
| SLR | Off (Close) | Off (Close) | Off (Close) | Off (Close) | |
| Switching Solenoid Valve | SSC | On (Open) | On (Open) | On (Open) | On (Open) |
| SCC | On (Open) | On (Open) | On (Open) | On (Open) | |
| SMC | Off (Open) | On (Close) | On (Close) | On (Close) | |
| SRC | Off (Open) | On (Close) | On (Close) | On (Close) | |
| Pressure Holding Solenoid Valve | FLH | Off (Open) | Off (Open) | On (Close) | On (Close) |
| FRH | Off (Open) | Off (Open) | On (Close) | On (Close) | |
| RLH | Off (Open) | On (Close) | On (Close) | On (Close) | |
| RRH | Off (Open) | Off (Open) | On (Close) | On (Close) | |
| Pressure Reduction Solenoid Valve | FLR | Off (Close) | Off (Close) | Off (Close) | On (Open) |
| FRR | Off (Close) | Off (Close) | Off (Close) | On (Close) | |
| RLR | Off (Close) | Off (Close) | Off (Close) | Off (Close) | |
| RRR | Off (Close) | Off (Close) | Off (Close) | On (Open) | |
In the rear wheel skid restraining control, the brakes of the front and rear wheels on the outer circle of the turn are applied. Also, depending on whether the brake is on or off and the condition of the vehicle, there are circumstances in which the brake might not be applied to the wheels even if the wheel is targeted for braking. The diagram below shows the hydraulic circuit in the pressure increase mode, as it controls the rear wheel skid condition while the vehicle makes a right turn. In other operating modes, the pressure holding valve and the pressure reduction valve are turned on/off according to the ABS with EBD operation patterns.
| *1 | Reservoir Tank | *2 | Brake Fluid Level Warning Switch |
| *3 | Accumulator | *4 | Pump Motor |
| *5 | Pressure Relief Valve | *6 | Hydraulic Brake Booster |
| *7 | Stroke Simulator | *8 | Switching Solenoid Valve SSC |
| *9 | Master Cylinder Pressure Sensor | *10 | Accumulator Pressure Sensor |
| *11 | Switching Solenoid Valve SMC | *12 | Switching Solenoid Valve SRC |
| *13 | Pressure Control Solenoid Valve SLA | *14 | Front Wheel Cylinder Pressure Sensor |
| *15 | Switching Solenoid Valve SCC | *16 | Pressure Control Solenoid Valve SLR |
| *17 | Pressure Holding Solenoid Valve FLH | *18 | Pressure Holding Solenoid Valve FRH |
| *19 | Pressure Holding Solenoid Valve RLH | *20 | Pressure Holding Solenoid Valve RRH |
| *21 | Pressure Reduction Solenoid Valve FLR | *22 | Pressure Reduction Solenoid Valve FRR |
| *23 | Pressure Reduction Solenoid Valve RLR | *24 | Pressure Reduction Solenoid Valve RRR |
| *25 | Front Left Wheel Cylinder | *26 | Front Right Wheel Cylinder |
| *27 | Rear Left Wheel Cylinder | *28 | Rear Right Wheel Cylinder |
| *29 | Brake Actuator | - | - |
| Item | VSC not Activated | VSC Activated | |||
|---|---|---|---|---|---|
| Increase Mode | Holding Mode | Reduction Mode | |||
| Pressure Control Solenoid Valve | SLA | Off (Close) | On (Open) | On (Open) | On (Open) |
| SLR | Off (Close) | Off (Close) | Off (Close) | Off (Close) | |
| Switching Solenoid Valve | SSC | On (Open) | On (Open) | On (Open) | On (Open) |
| SCC | On (Open) | On (Open) | On (Open) | On (Open) | |
| SMC | Off (Open) | On (Close) | On (Close) | On (Close) | |
| SRC | Off (Open) | On (Close) | On (Close) | On (Close) | |
| Pressure Holding Solenoid Valve | FLH | Off (Open) | Off (Open) | On (Close) | On (Close) |
| FRH | Off (Open) | On (Close) | On (Close) | On (Close) | |
| RLH | Off (Open) | Off (Open) | On (Close) | On (Close) | |
| RRH | Off (Open) | On (Close) | On (Close) | On (Close) | |
| Pressure Reduction Solenoid Valve | FLR | Off (Close) | Off (Close) | Off (Close) | On (Open) |
| FRR | Off (Close) | Off (Close) | Off (Close) | Off (Close) | |
| RLR | Off (Close) | Off (Close) | Off (Close) | On (Open) | |
| RRR | Off (Close) | Off (Close) | Off (Close) | Off (Close) | |
Hill-start Assist Control Operation
Hill-start Assist Control helps maintain 4-wheel hydraulic pressure by operating the pressure control solenoid valve when the driver releases the brake pedal until depressing the accelerator pedal.
Based on the information provided by various sensors, switches, and the power management control ECU, the skid control ECU determines whether to activate Hill-start Assist Control.
During Hill-start Assist Control, the slip indicator light blinks and the stop light are illuminated.
| *1 | Reservoir Tank | *2 | Brake Fluid Level Warning Switch |
| *3 | Accumulator | *4 | Pump Motor |
| *5 | Pressure Relief Valve | *6 | Hydraulic Brake Booster |
| *7 | Stroke Simulator | *8 | Switching Solenoid Valve SSC |
| *9 | Master Cylinder Pressure Sensor | *10 | Accumulator Pressure Sensor |
| *11 | Switching Solenoid Valve SMC | *12 | Switching Solenoid Valve SRC |
| *13 | Pressure Control Solenoid Valve SLA | *14 | Front Wheel Cylinder Pressure Sensor |
| *15 | Switching Solenoid Valve SCC | *16 | Pressure Control Solenoid Valve SLR |
| *17 | Pressure Holding Solenoid Valve FLH | *18 | Pressure Holding Solenoid Valve FRH |
| *19 | Pressure Holding Solenoid Valve RLH | *20 | Pressure Holding Solenoid Valve RRH |
| *21 | Pressure Reduction Solenoid Valve FLR | *22 | Pressure Reduction Solenoid Valve FRR |
| *23 | Pressure Reduction Solenoid Valve RLR | *24 | Pressure Reduction Solenoid Valve RRR |
| *25 | Front Left Wheel Cylinder | *26 | Front Right Wheel Cylinder |
| *27 | Rear Left Wheel Cylinder | *28 | Rear Right Wheel Cylinder |
| *29 | Brake Actuator | - | - |
| Item | Hill-start Assist Control not Activated | Hill-start Assist Control Activated | ||
|---|---|---|---|---|
| Holding Mode | Reduction Mode | |||
| Pressure Control Solenoid Valve | SLA | Off (Close) | On (Open) | Off (Close) |
| SLR | Off (Close) | Off (Close) | On (Open) | |
| Switching Solenoid Valve | SSC | On (Open) | On (Open) | On (Open) |
| SCC | On (Open) | On (Open) | On (Open) | |
| SMC | Off (Open) | On (Close) | On (Close) | |
| SRC | Off (Open) | On (Close) | On (Close) | |
| Pressure Holding Solenoid Valve | FLH | Off (Open) | Off (Open) | Off (Open) |
| FRH | Off (Open) | Off (Open) | Off (Open) | |
| RLH | Off (Open) | Off (Open) | Off (Open) | |
| RRH | Off (Open) | Off (Open) | Off (Open) | |
| Pressure Reduction Solenoid Valve | FLR | Off (Close) | Off (Close) | Off (Close) |
| FRR | Off (Close) | Off (Close) | Off (Close) | |
| RLR | Off (Close) | Off (Close) | Off (Close) | |
| RRR | Off (Close) | Off (Close) | Off (Close) | |
VSC (Cooperative Control with EPS) Operation
The operation of the solenoid valves under the cooperative control with EPS is the same as the brake control functions (ABS, TRC, VSC) operation.