Home › Brake › BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS › BRAKE CONTROL SYSTEM › 2012.02–2015.04
NM2040EQ _54 Brake _014497 BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS _0073595 BRAKE CONTROL SYSTEM DE DETAILS F

BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS  BRAKE CONTROL SYSTEM  DETAILS  BRAKE PEDAL STROKE SENSOR  


CONSTRUCTION


a.

A non-contact type brake pedal stroke sensor is used.


b.

This sensor detects the extent of the brake pedal stroke and transmits it to the skid control ECU.

X104965
1.885,0.313 2.198,0.313 2.198,0.313 2.781,1.625 true 4.688,0.76 4.823,0.76 4.823,0.76 5.115,1.229 true 5.813,0.479 5.667,0.479 5.667,0.479 5.26,0.958 true 4.198,2.313 4.323,2.313 4.323,2.313 4.604,2.021 true 5.188,3.958 4.948,3.958 4.948,3.958 4.427,3.604 true 5.167,4.625 4.917,4.625 4.917,4.625 4.375,4.948 true 0.177,0.198 1.865,0.573 1.688,0.375 10 false Brake Pedal Stroke Sensor 2.24,1.167 2.365,1.344 0.125,0.177 10 true A 3.198,2.167 3.323,2.365 0.125,0.198 10 false A 3.813,2.198 4.156,2.458 0.344,0.26 10 false Lever 2.063,3.406 2.417,3.615 0.354,0.208 10 false 4.5 V 2.167,4.813 2.417,5.042 0.25,0.229 10 false 1 V 2.167,5.281 2.417,5.479 0.25,0.198 10 false 0 V 2.542,5.281 2.958,5.531 0.417,0.25 10 false -9.7° 2.958,5.281 3.146,5.49 0.188,0.208 10 false 0 4.406,5.271 4.792,5.521 0.385,0.25 10 false 58.3° 4.792,5.365 6.771,5.708 1.979,0.344 10 false Sensor Lever Rotational Angle 1.927,3.042 2.438,3.323 0.51,0.281 10 false Voltage 5.24,3.833 5.667,4.083 0.427,0.25 10 false SKS1 5.208,4.521 5.677,4.771 0.469,0.25 10 false SKS2 4.927,2.594 6.135,2.885 1.208,0.292 10 false A-A Cross Section 3.823,0.656 4.667,0.927 0.844,0.271 10 false Sensor Shaft 5.844,0.375 7.031,0.719 1.188,0.344 10 false Return Spring 2.063,5.042 2.427,5.26 0.365,0.219 10 false 0.4 V

HINT:
·

To install a brake pedal stroke sensor, which is available as a service part, perform as follows:

·

The sensor lever is secured with a pin to "0" stroke. (Do not detach the pin until the installation has been completed.)

·

In this state, install the sensor on the brake pedal (in the OFF state) on the vehicle.

·

After completing the installation, firmly press the brake pedal once to break off the pin that is securing the sensor in place.

·

Make sure the broken pin does not remain in the sensor lever.



·

After replacing the brake pedal stroke sensor, initialization of brake pedal stroke sensor must be required on the skid control ECU side. For Details, refer to the Repair Manual.