Home › Vehicle Interior › METER / GAUGE / DISPLAY › METER / GAUGE SYSTEM › 2012.02–2015.04
NM2040EQ _58 Vehicle Interior _014511 METER / GAUGE / DISPLAY _0073617 METER / GAUGE SYSTEM DE DETAILS F

METER / GAUGE / DISPLAY  METER / GAUGE SYSTEM  DETAILS  COMBINATION METER  


FUNCTION


a.

Combination Meter Assembly

i.

Buzzer Function

1.

The table below shows the warning and reminder functions of the buzzer in the combination meter assembly.

*: Models with sliding roof system

1 READY 2 Seat Belt Warning (Level 2)
3 Seat Belt Warning (Level 1) 4 Rear Passenger Side Seat Belt Warning
5 Brake System Warning 6 EPS Warning
7 Smart Entry and Start System Warning 1 (Continuous) 8 Smart Entry and Start System Warning 2 (Intermittent)
9 Key Reminder Indicating Buzzer 10 Brake System Temperature Warning
11 Hill-start Assist Control Reset Indication 12 Hill-start Assist Control Set Indication
13 Smart Entry and Start System Warning 2 (Continuous, 9 times at the maximum) 14 Smart Entry and Start System Warning (Once)
15 Multi-information Display Warning 16 Accelerator Depression with Shift Lever in N
17 Smart Entry and Start System Warning (Intermittent) 18 Hybrid System Check (Intermittent)
19 Hybrid System Check (Once) 20 HV Battery Low Warning
21 HV Battery Charge Request 22 Immobiliser Certification Reminder
23 Shift Position (P) Request 24 Parking Brake Engaged Warning
25 Door Open while Driving Warning 26 Shift Operation Reject Warning
27 EV Drive Mode Reject Warning 28 Sliding Roof Open Warning*
29 Turn Signal/Hazard Warning Operation - -




b.

Multi-information Display

i.

Display Flow Function

1.

The multi-information display flow can be switched as shown in the flow chart below:

Y111604
4.115,0.885 4.615,1.292 0.5,0.406 10 false OFF 1.365,1.604 2.479,2.01 1.115,0.406 10 false Cyclic Display*2 2.115,1.271 2.333,1.51 0.219,0.24 10 false *1 2.427,4.542 2.646,4.781 0.219,0.24 10 false *4 0.771,5.427 0.99,5.667 0.219,0.24 10 false *5 1.427,0.719 2.396,1.125 0.969,0.406 10 false New Message 1.198,3.188 1.948,3.594 0.75,0.406 10 false Opening*3 5.604,4.375 6.49,4.781 0.885,0.406 10 false DTC Display 3.406,5.719 4.542,6.125 1.135,0.406 10 false New Message 0.865,5.708 1.958,6.115 1.094,0.406 10 false Cyclic Display*1 0.542,6.688 1.896,7 1.354,0.313 10 false : Conditions met 0.542,7.177 1.917,7.49 1.375,0.313 10 false : Conditions not met 2.24,7.177 3.667,7.49 1.427,0.313 10 false : DISP switch operated 2.24,6.677 3.656,6.969 1.417,0.292 10 false : Setting completed 3.104,4.365 4.198,4.771 1.094,0.406 10 false Advisory Display 0.938,4.354 2.083,4.781 1.146,0.427 10 false Cruise Information Display 3.75,1.625 4.969,2.042 1.219,0.417 10 false Farewell Message 1.552,2.531 2.927,2.844 1.375,0.313 10 false Power Switch On (IG) 5.677,0.979 6.531,1.573 0.854,0.594 10 false Door Unlock Mode Display 4.344,2.531 5.75,2.854 1.406,0.323 10 false Power Switch OFF

No. Transition Condition
*1 Conditions are not met and all new messages have been displayed.
*2 If the display conditions for 2 or more messages are met, relevant messages are alternately displayed for 2 seconds each.
*3 If the power switch is turned off during the "Opening" display, the "Opening" display will be shown from the beginning.
*4 If the DISP switch is used to change from an advisory message to the cruise information display screen, repeatedly operating the DISP switch will cycle through the cruise information screens and then return the advisory message if the display conditions are still met.
*5 If the DISP switch is not operated for more than 6 seconds with any of the caution or warning message display conditions still met, the relevant caution or warning messages are displayed.



ii.

Cruise Information Mode Function

1.

The cruise information is displayed in the following order each time the DISP switch of the steering pad switch assembly is pressed.

Y112138
1.573,3.26 1.75,2.708 1.75,2.708 2.344,2.708 true 2.406,2.604 2.729,2.885 0.323,0.281 10 false *1 3.25,0.167 3.49,0.406 0.24,0.24 10 false (1) 3.25,1.813 3.49,2.052 0.24,0.24 10 false (2) 3.25,3.479 3.49,3.719 0.24,0.24 10 false (3) 5.552,3.479 5.792,3.719 0.24,0.24 10 false (4) 5.552,1.813 5.792,2.052 0.24,0.24 10 false (5) 5.552,0.167 5.792,0.406 0.24,0.24 10 false (6)
*1 DISP Switch - -
V100136

DISP switch pressed briefly. - -


2.

The cruise information mode items displayed are as follows:

No. Information Outline
(1) Cruising Range
·

Displays a value that has been calculated by the combination meter assembly. When the power switch is turned on (IG), the combination meter assembly calculates the range based on continuously monitoring and storing information on fuel consumption data, and the residual fuel volume.

·

This display is updated every 10 seconds.


Average Fuel Consumption
·

Displays a value that has been calculated by the combination meter assembly based on the distance driven and the fuel consumption volume (fuel injection signal from the ECM).

·

This display is updated every 10 seconds.


(2) Average Speed
·

Displays the average vehicle speed calculated by the combination meter assembly based on the engine start signal and vehicle speed signal.

·

This display is updated every 10 seconds.


Elapsed Time Displays the length of time since the hybrid system was started.
(3) Eco Drive Level Display
·

Displays the average fuel consumption calculated since the hybrid system was started. Uses 4 different height bars to display the level.

·

This display is updated every 10 seconds.


(4) Energy Monitor
·

Displays the energy transmission direction for checking the current drive method (engine, motor or both), whether the engine is being used to generate power or whether energy is being regenerated.

·

The energy flow, which appears in the form of an arrow, also shows the SOC of the HV battery in 8 levels.

·

This display is updated every 0.3 seconds.


(5) Settings Customizes the combination meter assembly language display and EV drive indicator light and instantaneous fuel consumption gauge deactivated or activated display states.
(6) Blank Screen -



iii.

Eco Drive Level

1.

The eco drive level changes among 4 levels to indicate the average fuel consumption.

2.

After the power switch is turned off, the eco drive level display appears for 3 seconds in the multi-information display. When the average fuel consumption is 5.8 L/100 km or less the "EXCELLENT!" message flashes.

Average Fuel Consumption Level (L/100km) Multi-information Display
Level 0 (9 or more)
Y137651

Level 1 (8 to 9)
Y137652

Level 2 (7 to 8)
Y137653

Level 3 (6 to 7)
Y137654

Level 4 (less 6) When driving
Y137655

After power source is turned off
Y137656




iv.

Customization Function

1.

In the settings screen of cruise information mode, pressing and holding the DISP switch enters setting mode.

2.

Press the DISP switch briefly to select the item to be customized. Press and hold the DISP switch to confirm the selection.

Y112152
4.396,0.25 4.719,0.531 0.323,0.281 10 false *a 4.396,1.677 4.719,1.958 0.323,0.281 10 false *b 4.396,3.094 4.719,3.375 0.323,0.281 10 false *c
*a Language Setting *b Instantaneous Fuel Consumption Gauge
*c EV Drive Indicator Light ON/OFF Setting - -
V100136

DISP switch pressed briefly.
V100135

DISP switch pressed and held.
V100137

If the vehicle has reached a speed of 8 km/h (5 mph) - -


3.

In setting mode, the following items of the combination meter assembly can be customized.

Item Available Setting
Language
·

English

·

French

·

Spanish


Instantaneous Fuel Consumption Gauge
·

On

·

Off


EV Drive Indicator Light
·

On

·

Off





v.

Warning Mode Function

1.

When a warning is necessary, the warning display interrupts the display in the multi-information display.

2.

The master warning light may illuminate or blink and the buzzer in the combination meter assembly may sound depending on the item in the multi-information display.

Priority Indication/Warning Master Warning Light Buzzer

*1: If the vehicle has reached a speed of 5 km/h (3 mph).

*2: Models with blind spot monitor system

*3: Models with sliding roof system

1 MAINTENANCE MODE - -
CERTIFICATION MODE - -
2 Door Open (While Driving)*1 Blinks Sounds
Door Open - -
3 AUTO POWER OFF TO CONSERVE BATTERY - -
4 SHIFT TO P POSITION Blinks Sounds
SHIFT TO P POSITION WHEN PARKED Blinks Sounds
N POSITION Blinks Sounds
TRACTION BATTERY PRESERVATION MODE RESTART AFTER SHIFTING TO THE P POSITION Blinks Sounds
5 TRACTION BATTERY LOW. CHARGE WHEN NOT IN N POSITION Blinks Sounds
RELEASE PARKING BRAKE Blinks Sounds
KEY NOT DETECTED Blinks Sounds
6 CHECK HYBRID SYSTEM Illuminates Sounds
CHECK ENTRY & START SYSTEM Blinks Sounds
7 CHECK CRUISE CONTROL SYSTEM Illuminates Sounds
BSM NOT AVAILABLE*2 Illuminates Sounds
CHECK BSM SYSTEM*2 Illuminates Sounds
8 TURN POWER OFF Blinks Sounds
9 KEY DETECTED IN VEHICLE Blinks Sounds
MOONROOF OPEN*3 Blinks Sounds
DEPRESS BRAKE PEDAL, TOUCH POWER SWITCH WITH KEY Blinks Sounds
DEPRESS BRAKE PEDAL AND PUSH POWER SWITCH TO START Blinks Sounds
STEERING LOCK ACTIVE Blinks Sounds
SHIFT TO P POSITION TO START Blinks Sounds
10 KEY BATTERY LOW Illuminates Sounds
HYBRID SYSTEM OVERHEAT Illuminates Sounds
11 DRIVING FORCE LIMITED - -
POWER ON - -
Hybrid System Start Ready State - -
EV MODE CURRENTLY NOT AVAILABLE - Sounds
EV MODE NOT AVAILABLE WARMING UP - Sounds
EV MODE NOT AVAILABLE LOW BATTERY - Sounds
EV MODE NOT AVAILABLE EXCESSIVE SPEED - Sounds
EV MODE NOT AVAILABLE EXCESSIVE ACCELERATION - Sounds
EV MODE DEACTIVATED - Sounds
EV MODE DEACTIVATED LOW BATTERY - Sounds
EV MODE DEACTIVATED EXCESSIVE SPEED - Sounds
EV MODE DEACTIVATED EXCESSIVE ACCELERATION - Sounds





SYSTEM CONTROL


a.

Hybrid System Indicator Operation

i.

The Hybrid System Indicator will begin to operate when both of the following conditions are met:

·

The hybrid system is operating (the READY indicator light is illuminated).

·

The shift position is not in P, R or N.