Home › Vehicle Interior › SEAT › POWER SEAT CONTROL SYSTEM
NM2040EQ _58 Vehicle Interior _014513 SEAT _0073620 POWER SEAT CONTROL SYSTEM CO CONTROL F

SEAT  POWER SEAT CONTROL SYSTEM  CONTROL  SEAT CONTROL  


SYSTEM CONTROL


a.

Seat Position Detection Method

i.

Power Seats with Memory Function

1.

The Hall IC installed on the power seat motor generates pulses corresponding to the speed of the motor. These pulses are then picked up by the position control ECU and switch assembly in order to detect the seat position.


Y103923
1.74,1.49 1.74,0.719 1.74,0.719 1.313,0.719 true 2.948,1.208 2.948,0.333 2.948,0.333 3.313,0.333 true 6.271,2.531 5.427,2.531 true 1.625,2.531 0.781,2.531 true 6.333,2.438 6.573,2.656 0.24,0.219 10 *2 0.594,2.427 0.823,2.719 0.229,0.292 10 *1 3.344,0.24 3.573,0.458 0.229,0.219 10 *a 1.125,0.625 1.365,0.844 0.24,0.219 10 *3
*1 Power Seat Motor *2 Position Control ECU and Switch Assembly
*3 Hall IC - -
*a Current pulsations generated by motor - -




b.

Memory Function for Driver Seat

i.

The memory, recall and memory call conditions of the memory function are as follows:

Function Condition Operation Action

*: Seat movement distance can be changed using the customized body electronics system. For details, refer to the Repair Manual.

Memory Power switch is on (IG). Switch 1 or 2 is pressed while the "SET" button is pressed.
·

Memorizes the seat position when switch 1 or 2 is pressed.

·

When the memory setting is completed, the buzzer will sound for 0.5 seconds.


Switch 1 or 2 is pressed within 3 seconds after the "SET" button is pressed.
Recall
·

Power switch is on (IG).

·

The shift lever is in P.

·

Memory switch is off.

·

Seat position is memorized.


Switch 1 or 2 is pressed. Recalls the seat position that was memorized in the position control ECU and switch assembly.
·

Power switch is off.

·

Memory switch is off.

·

Seat position is memorized.

·

Driver door is opened.


Switch 1 or 2 is pressed within 180 seconds after power switch is turned off and driver door is opened.
·

Power switch is off.

·

Memory switch is off.

·

Seat position is memorized.

·

Open driver door is closed.


Switch 1 or 2 is pressed within 60 seconds after power switch is turned off and the open driver door is closed.




FUNCTION


a.

Memory Function for Driver Seat

i.

The power seat control system has the following functions:

Function Outline
Power Control The fore-and-aft slide, reclining, front vertical, lifter and lumbar support can be adjusted using the power seat switch.
Memory Memory The memory function can memorize 2 different seat positions.
Recall The recall function can recall 2 different memorized seat positions.


ii.

The memory function works in combination with the following systems, ensuring usability and enabling easy entering or exiting of the vehicle.

System Outline
Electrical Remote Mirror System (Models with Memory Function) The outer mirror control ECU assembly memorizes the outside rear view mirror positions and recalls them when all conditions are met.




DIAGNOSIS


a.

The position control ECU and switch assembly (position control ECU) has a diagnosis function. It stores a record of any power seat control system failures in its memory in the form of Diagnostic Trouble Codes (DTCs).


b.

The position control ECU and switch assembly (position control ECU) outputs malfunction data and 5-digit DTCs to the intelligent tester.


c.

The 5-digit DTCs can be read after connecting the intelligent tester to the DLC3. For details, refer to the Repair Manual.