Home › Vehicle Exterior › LIGHTING (EXT) › LIGHTING SYSTEM › 2012.02–2015.04
NM2040EQ _59 Vehicle Exterior _014520 LIGHTING (EXT) _0073628 LIGHTING SYSTEM CO CONTROL F

LIGHTING (EXT)  LIGHTING SYSTEM  CONTROL  AUTOMATIC HIGH BEAM  


FUNCTION OF MAIN COMPONENTS


Component Function
Inner Rear View Mirror Assembly Automatic High Beam Sensor The automatic high beam sensor determines when to turn the high beams on and off after identifying the lights of oncoming vehicles, preceding vehicles and other lights from the picture information of its camera sensor. Then, it sends high beam request signals to the headlight swivel ECU assembly via Local Interconnect Network (LIN).
Headlight Swivel ECU Assembly
·

The headlight swivel ECU assembly uses LIN communication (for automatic high beam actuation).

·

The headlight swivel ECU assembly acts as the gateway between the automatic high beam sensor and the CAN system.


Main Body ECU (Multiplex Network Body ECU)
·

The main body ECU (multiplex network body ECU) receives an AUTO position signal and high beam position signal from headlight dimmer switch.

·

The main body ECU (multiplex network body ECU) receives high beam request signals from the mirror and transmits a signal to the power distributor.


Skid Control ECU The skid control ECU outputs information about the average speed of the 4 wheels. This information is used by the automatic high beam sensor to control switching between the high and low beams of the automatic high beam system.
ECM The ECM outputs a signal to indicate that the shift lever is in R. Based on this signal, the automatic high beam sensor determines the direction of vehicle movement.
Headlight Dimmer Switch Assembly The headlight dimmer switch assembly transmits an AUTO position or high beam position signal to the main body ECU (multiplex network body ECU).
Automatic Light Control Sensor The automatic light control sensor detects the ambient light level and transmits a signal to the main body ECU (multiplex network body ECU).
Combination Meter Assembly Automatic High Beam Indicator Light
·

The automatic high beam indicator light (yellow) illuminates to inform the driver when malfunctions are detected in this system.

·

The automatic high beam indicator light (green) illuminates to inform the driver when the automatic high beam system is activated.


Headlight High Beam Indicator Light The headlight high beam indicator light illuminates to inform the driver when the high beams are on.


FUNCTION


a.

When passing an oncoming vehicle:

1.

The automatic high beam system turns off the high beams before an oncoming vehicle comes within approximately 800 m (2625 ft.).

2.

When an oncoming vehicle passes out of camera sensor range, the automatic high beam system turns the high beams on after a short delay.

Y100276
5.177,3.25 5.177,3.448 true 3,0.323 4.021,0.5 1.021,0.177 10 false 800 m (2625 ft.) 3.865,1.802 4.292,1.969 0.427,0.167 10 false Delay 4.479,3.458 6.146,3.625 1.667,0.167 10 false Camera Sensor Angle

HINT:
·

The detection distance varies depending on detected objects.

·

The timing of turning on and off the high beams varies depending on the intensity of oncoming (and preceding) vehicle lights.





b.

When passing a preceding vehicle:

1.

When approaching a preceding vehicle, the automatic high beam system turns off the high beams approximately 600 m (1969 ft.) before reaching it.

2.

When a preceding vehicle passes out of camera sensor range, the automatic high beam system turns the high beams on after a short delay.

Y100277
5.25,3.313 5.25,3.521 true 2.844,0.406 3.865,0.604 1.021,0.198 10 false 600 m (1969 ft.) 3.792,3.365 4.25,3.625 0.458,0.26 10 false Delay 4.656,3.51 6.156,3.771 1.5,0.26 10 false Camera Sensor Angle

HINT:

The timing of turning on and off the high beams varies depending on the intensity of the preceding vehicle lights.





SYSTEM CONTROL


a.

The automatic high beam system operates as follows.

Condition Details
Active When all of the following conditions are met, the automatic high beam system is activated and the automatic high beam indicator light turns on:
·

Turn the power switch to on (IG).

·

The headlight dimmer switch is in the AUTO position and high beam position.

·

The automatic light control sensor outputs the night mode signal (to turn the headlights on).


High Beams on When all of the following conditions are met, the automatic high beam system turns on the high beams after a short delay:
·

Vehicle speed is more than approximately 32 km/h.

·

The area in front of the vehicle is dark.

·

No oncoming vehicles are present with the headlights on.

·

No preceding vehicles are present with the taillights on.

·

Few streetlights are present along the street ahead.


High Beams off When any of the following conditions are met, the automatic high beam system turns off the high beams after a short delay:
·

Vehicle speed is less than approximately 32 km/h.

·

The area in front of the vehicle is not dark.

·

An oncoming vehicle with headlights on is detected.

·

A preceding vehicle with taillights on is detected.

·

Several streetlights are present along the street ahead.





DIAGNOSIS


a.

When the headlight swivel ECU assembly or main body ECU (multiplex network body ECU) detects malfunctions in the automatic high beam system, Diagnostic Trouble Codes (DTCs) are stored in memory.


b.

The DTCs can be read using the intelligent tester. For details, refer to the Repair Manual.