Home › Vehicle Interior › PRE-CRASH SAFETY › PRE-CRASH SAFETY SYSTEM › from 2015.04
NM2040EQ _58 Vehicle Interior _036091 PRE-CRASH SAFETY _0166756 PRE-CRASH SAFETY SYSTEM CO CONTROL F

PRE-CRASH SAFETY  PRE-CRASH SAFETY SYSTEM  CONTROL  PRE-CRASH SAFETY CONTROL  


FUNCTION OF MAIN COMPONENTS


Item Function
Combination Meter Assembly PCS Warning Light
·

Illuminates to warn the driver in accordance with signals from the driving support ECU assembly.

·

Flashes when the system is malfunctioning or temporarily disabled.

·

Illuminates when the pre-crash safety system is not available due to certain reasons or when pre-crash brake and pre-crash brake assist operation are disabled since the VSC system has been disabled.


Multi-information Display Displays a warning message to inform or warn the driver of the system condition in accordance with signals from the driving support ECU assembly.
Master Warning Light Illuminates to warn the driver in accordance with signals from the driving support ECU assembly.
Buzzer Sounds to warn the driver in accordance with signals from the driving support ECU assembly when the system is malfunctioning.
Millimeter Wave Radar Sensor Assembly
·

Radiates millimeter wave radar forward, uses the reflected millimeter waves for detecting the presence of a vehicle ahead, the vehicle-to-vehicle distance, and the relative speed, and then transmits this information to the driving support ECU assembly.

·

Sounds the skid control buzzer assembly according to signals from the driving support ECU assembly.


Driving Support ECU Assembly Determines whether the possibility of a collision is high or a collision is unavoidable based on the information received from the millimeter wave radar sensor assembly. It then outputs a brake assist standby request signal and pre-crash brake request signal if required.
Brake Booster Pump Assembly Receives an operation signal from the skid control ECU and generates hydraulic pressure for brake control.
Brake Booster with Master Cylinder Assembly Master Cylinder Pressure Sensor Detects the master cylinder pressure and transmits a signal to the skid control ECU.
Skid Control ECU
·

Receives a brake assist standby request signal from the driving support ECU assembly and switches the brake assist to standby mode. When a stop light switch signal is input, it activates the brake assist.

·

Receives a pre-crash brake request signal from the driving support ECU assembly, and then applies the brakes.

·

Transmits vehicle speed signals to the driving support ECU assembly.


Speed Sensors Detect the wheel speed of each of the 4 wheels and transmits the signals to the skid control ECU.
Airbag Sensor Assembly Yawrate Sensor Detects the yaw rate and lateral/longitudinal deceleration of the vehicle and transmits the signal to the driving support ECU assembly.
Steering Sensor Detects the angle and direction of steering and transmits a signal to the driving support ECU assembly.
Pre-crash System Switch Assembly (Pre-crash System Cancel Switch Assembly)
·

Switches between the 3 warning timings (Far, Middle and Near) when pressed.

·

Disables the pre-crash safety system when pressed and held.


Skid Control Buzzer Assembly Sounds to warn the driver in accordance with signals from the millimeter wave radar sensor assembly.
Stop Light Switch Assembly Detects if the brake pedal is depressed and transmits a signal to the driving support ECU assembly.
Engine Room Relay Block and Junction Block Assembly Stop Light Control Relay Receives a stop light turn on request signal from the skid control ECU and turns on the stop lights.
VSC OFF Switch Disables the pre-crash brake and pre-crash brake assist operation when the switch is turned on.


SYSTEM CONTROL


a.

High Possibility of Collision or Unavoidable Collision

(1) The driving support ECU assembly determines that the possibility of a collision is high based on the signals received from the millimeter wave radar sensor assembly, steering sensor, speed sensor and yawrate sensor.
(2) The driving support ECU assembly transmits a PCS warning display request signal to the combination meter assembly and a skid control buzzer assembly request signal to the millimeter wave radar sensor assembly.
(3) The driving support ECU assembly outputs a pre-crash brake assist request signal to the skid control ECU. Upon receiving this signal, the skid control ECU switches the brake assist to the standby condition. At this time, the skid control ECU activates pre-crash brake assist when the brake pedal is depressed by the driver.
(4) The driving support ECU assembly determines that an unavoidable collision condition exists based on the signals received from the millimeter wave radar sensor assembly, speed sensor, steering sensor and yawrate sensor.
(5) The driving support ECU assembly outputs a pre-crash brake request signal to the skid control ECU.
(6) The skid control ECU decreases the vehicle speed by activating the brake booster pump assembly to perform a pre-crash brake operation and activates the stop light control relay to turn on the stop lights.
(7) If no collision occurs, the brake assist will return to its normal state.

Y172289E03
1.677,5.771 1.823,5.771 1.823,5.771 2.406,5.302 true 4.75,1.229 5.677,1.063 5.677,1.063 5.885,1.063 true 5.792,3.188 5.792,3.615 5.792,3.615 5.927,3.615 true 0.396,0.24 1.646,0.698 1.25,0.458 10 false Skid Control Buzzer Assembly 0.146,1.219 2.677,1.635 2.531,0.417 10 false Pre-crash System Switch Assembly (Pre-crash System Cancel Switch Assembly) 0.49,2.125 2.302,2.417 1.813,0.292 10 false Stop Light Switch Assembly 0.406,2.844 1.615,3.188 1.208,0.344 10 false Combination Meter Assembly 0.219,3.646 1.5,3.979 1.281,0.333 10 false - PCS Warning Light 0.219,4.042 1.844,4.323 1.625,0.281 10 false - Multi-information Display 0.229,4.479 1.729,4.771 1.5,0.292 10 false - Master Warning Light 0.25,4.917 1.198,5.146 0.948,0.229 10 false - Buzzer 2.26,2.865 2.563,3.063 0.302,0.198 10 false (2) 3.292,2.823 3.76,3.021 0.469,0.198 10 false (3), (5) 3.281,3.625 3.75,3.823 0.469,0.198 10 false (1), (4) 3.333,4.406 3.802,4.604 0.469,0.198 10 false (1), (4) 3,5.125 3.469,5.323 0.469,0.198 10 true (1), (4) 1.854,5.833 2.323,6.031 0.469,0.198 10 false (3), (5) 0.833,5.708 1.656,5.948 0.823,0.24 10 false CAN (V Bus) 5.969,3.521 7.115,3.76 1.146,0.24 10 false CAN (Sub Bus 11) 5.688,2.625 6.135,2.854 0.448,0.229 10 false (1), (4) 5.771,1.344 6.594,1.563 0.823,0.219 10 false (2), (3), (5) 2.885,0.333 3.188,0.531 0.302,0.198 10 false (2) 5.104,1.188 5.406,1.385 0.302,0.198 10 false (2) 3.875,1.198 4.344,1.396 0.469,0.198 10 false (1), (4) 4.073,0.25 5.469,0.604 1.396,0.354 10 false Millimeter Wave Radar Sensor Assembly 4.104,1.583 5.375,1.969 1.271,0.385 10 false Driving Support ECU Assembly 4.073,2.802 5.313,3.198 1.24,0.396 10 false Power Management Control ECU 4.24,3.719 5.406,3.969 1.167,0.25 10 false Steering Sensor 4.208,4.729 5.375,4.979 1.167,0.25 10 false - Yawrate Sensor 3.969,4.302 5.552,4.563 1.583,0.26 10 false Airbag Sensor Assembly 3.177,6.865 3.958,7.208 0.781,0.344 10 false Skid Control ECU 0.625,7.271 1.833,7.563 1.208,0.292 10 false VSC OFF Switch 0.688,6.177 1.896,6.469 1.208,0.292 10 false Speed Sensors 5.198,5.469 6.76,5.854 1.563,0.385 10 false Master Cylinder Pressure Sensor 5.26,6.438 6.563,6.833 1.302,0.396 10 false Brake Booster Pump Assembly 5.333,7.76 6.479,8.156 1.146,0.396 10 false Stop Light Control Relay 4.365,5.552 4.667,5.75 0.302,0.198 10 false (3) 4.208,6.583 4.698,6.76 0.49,0.177 10 true (6), (7) 4.229,7.74 4.531,7.938 0.302,0.198 10 false (6) 2.406,6.104 2.875,6.302 0.469,0.198 10 true (1), (4) 1.917,8.5 4.76,8.771 2.844,0.271 10 false Brake Booster with Master Cylinder Assembly 5.948,0.99 7.125,1.24 1.177,0.25 10 false CAN (Sub Bus 13)


b.

Operating Conditions

i.

The pre-crash safety system operates when the driving support ECU assembly determines there is a high possibility of a collision, or an unavoidable collision with an obstacle in front of the vehicle.

Operating Conditions Pre-crash safety system operation has not been disabled using pre-crash system switch assembly (pre-crash system cancel switch assembly)


ii.

The following pre-crash safety system controls are performed under the following conditions.

Control Condition
Pre-crash Warning
·

Vehicle speed is approximately 15 km/h (10 mph) or higher.

·

The relative speed of obstacle or vehicle ahead is approximately 10 km/h (7 mph) or higher.

·

Pre-crash safety system operation has not been disabled using pre-crash system switch assembly (pre-crash system cancel switch assembly).


Pre-crash Brake
·

Vehicle speed is approximately 15 km/h (10 mph) or higher.

·

The relative speed of obstacle or vehicle ahead is approximately 10 km/h (7 mph) or higher.

·

Pre-crash safety system operation has not been disabled using pre-crash system switch assembly (pre-crash system cancel switch assembly).

·

VSC system has not been disabled.


Pre-crash Brake Assist
·

Vehicle speed is approximately 30 km/h (19 mph) or higher.

·

The relative speed of obstacle or vehicle ahead is approximately 30 km/h (19 mph) or higher.

·

Brake pedal is depressed.

·

Pre-crash safety system operation has not been disabled using pre-crash system switch assembly (pre-crash system cancel switch assembly).

·

VSC system has not been disabled.






DIAGNOSIS


a.

Initial Check

i.

The driving support ECU assembly performs an initial check on the system for approximately 3 seconds after the power switch has been turned on (IG).



b.

Monitor Function

i.

After completing the initial check, the pre-crash safety system becomes ready to operate. During this time, the driving support ECU assembly periodically monitors the system for any malfunctions.



c.

Diagnostic Trouble Code (DTC)

i.

If the driving support ECU assembly detects a malfunction in the pre-crash safety system, it stores a 5 digit Diagnostic Trouble Code (DTC) in memory.