FUNCTION OF MAIN COMPONENTS
| Component | Function | |
|---|---|---|
|
*1: Models with pre-crash safety system *2: Models with dynamic radar cruise control system |
||
| Brake Booster Pump Assembly | ·
Consists of a pump, pump motor and accumulator. The hydraulic power source portion generates and stores hydraulic pressure, which the skid control ECU uses for controlling braking. ·
The relief valve is installed in the hydraulic brake booster. ·
The accumulator pressure sensor is installed in the brake actuator. |
|
| Brake Booster with Master Cylinder Assembly | Brake Actuator | ·
Consists of 4 switching solenoid valves, 2 pressure control solenoid valves, 8 control solenoid valves. ·
Changes the brake fluid path based on the signals from the skid control ECU during operation of the ABS with EBD, brake assist, TRC, VSC and Hill-start Assist Control in order to control the fluid pressure that is applied to the wheel cylinders. |
| Hydraulic Brake Booster | ·
Generates hydraulic pressure in accordance with the amount of effort applied to the brake pedal by the driver. ·
When a malfunction occurs in the brake system, the hydraulic brake booster supplies the fluid pressure (which is generated by brake pedal effort) directly to the wheel cylinders. |
|
| Relief Valve (Built into the Skid Control ECU) | ·
Returns the brake fluid to the reservoir tank to prevent excessive pressure if the pump operates continuously due to a malfunction of the accumulator pressure sensor. |
|
| Brake Pedal Stroke Simulator | Generates a pedal stroke during braking in accordance with the driver's pedal effort. | |
| Skid Control ECU | ·
Monitors the driving conditions of the vehicle in accordance with the signals received from the sensors and through cooperative control with the power management control ECU and EPS ECU calculates the required amount of braking force, and controls the brake actuator. ·
Judges the vehicle driving condition based on signals from each sensor, and controls ABS with EBD, brake assist, TRC, VSC and Hill-start Assist Control. ·
Operates the brake booster pump assembly to control accumulator pressure based on accumulator pressure sensor signal. |
|
| Brake Master Cylinder Reservoir Sub-assembly | Brake Fluid Level Warning Switch | Detects a low brake fluid level. |
| Brake Pedal Stroke Sensor | Directly detects the extent of the brake pedal stroke operated by the driver. | |
| Airbag Sensor Assembly | ·
The airbag sensor assembly incorporates the acceleration sensor and yawrate sensor. ·
The yawrate sensor detects the vehicle yaw rate. ·
The acceleration sensor detects the vehicle's longitudinal and lateral acceleration. ·
The airbag sensor assembly sends the detection signals from the yawrate sensor and acceleration sensor to the skid control ECU via the CAN communication. |
|
| Steering Sensor | Detects the steering direction and angle of the steering wheel. | |
| Speed Sensor | Detects the wheel speed of each of the 4 wheels. | |
| Stop Light Switch Assembly | Detects when the brake pedal is depressed. | |
| Parking Brake Switch Assembly | Detects the parking brake operating signal. | |
| VSC OFF Switch | Enables the driver to select "Normal mode", "TRC OFF mode", or "VSC OFF mode". | |
| Combination Meter Assembly | ABS Warning Light | Lights up to alert the driver when the skid control ECU detects a malfunction in the ABS, EBD or Brake Assist. |
| Brake Warning Light/Yellow (Minor Malfunction) | Lights up to alert the driver when a minor malfunction is detected in the brake system, which does not affect the braking force (such as a malfunction in the regenerative braking). | |
| Brake Warning Light/Red (Malfunction) | ·
Lights up to alert the driver when the skid control ECU detects a malfunction in the apportioning of the brake force. ·
Lights up to inform the driver when the parking brake is on or the brake fluid level is low. |
|
| Slip Indicator Light | ·
Blinks to inform the driver when the ABS, TRC or VSC is operated. ·
Lights up to alert the driver in the event of malfunction of the TRC, VSC or Hill-start Assist Control. |
|
| Master Warning Light | Lights up to alert the driver when the skid control ECU detects a malfunction in the brake control system. | |
| Buzzer | ·
Emits a warning sound to inform the driver when Hill-start Assist Control operation is started or finished. ·
This buzzer sounds continuously to inform the driver when there is a malfunction in the hydraulic pressure circuit or a failure in the power supply. |
|
| Multi-information Display | Shows a warning message to alert the driver, such as when the vehicle is being driven with the parking brake still engaged. | |
| Solenoid Relay (Built into the Skid Control ECU) | Supply or cut off power to solenoid valves in the brake actuator. | |
| Pump Motor Relays (Built into the Skid Control ECU) | Normally supplies power to the pump motor using 2 out of 3 relays. Ensures power to the pump motor by using the other relay if the skid control ECU detects a malfunction. | |
| Power Management Control ECU | ·
Actuates regenerative braking on receiving signal from the skid control ECU. ·
Sends the actual regenerative brake control value to the skid control ECU. ·
Controls the motive force based on an output control request signal received from the skid control ECU while the TRC or VSC is operating. |
|
| Power Steering ECU Assembly | Operates cooperatively with the skid control ECU to control the steering assist torque. | |
| Main Body ECU (Multiplex Network Body ECU) | Detects the parking brake signal and outputs it to the skid control ECU via CAN communication. | |
| Driving Support ECU Assembly*1, *2 | Makes a request for brake control to the skid control ECU assembly. | |
SYSTEM CONTROL
The brake control system (ABS with EBD, Brake Assist, TRC and VSC) has the following controls:
| Control | Outline | |
|---|---|---|
|
*1: Models with dynamic radar cruise control system *2: Models with pre-crash safety system |
||
| Electronically Controlled Brake System | Upon receiving signals from the skid control ECU, this system effects hydraulic pressure control at the 4 wheels. | |
| Regenerative Brake Cooperative Control | Controls hydraulic braking in order to recover electrical energy by utilizing the regenerative braking of the hybrid system as much as possible. | |
| Anti-lock Brake System (ABS) | The ABS helps prevent the wheels from locking when the brakes are applied firmly or when braking on a slippery surface. | |
| Electronic Brake Force Distribution (EBD) | Utilizes ABS, realizing proper brake force distribution between the front and rear wheels in accordance with the driving conditions. In addition, during braking while cornering, it also controls the brake force of the right and left wheels, helping maintain vehicle stability. | |
| Brake Assist | The primary purpose of Brake Assist is to provide an auxiliary brake force to assist a driver who cannot generate a large brake force during emergency braking, thus helping to fully utilize the vehicle's braking performance. | |
| Traction Control (TRC) | The TRC helps restrain the slippage of the drive wheels if the driver depresses the accelerator pedal excessively when starting off or accelerating on a slippery surface. | |
| VSC | Vehicle Stability Control (VSC) | The VSC helps restrain sideways slippage of the vehicle during a strong front wheel skid or strong rear wheel skid, during cornering. |
| Cooperative Control with EPS | Effects cooperative control with the power steering ECU assembly in order to provide steering assist in accordance with the operating conditions of the vehicle. | |
| Hill-start Assist Control | When starting uphill, this control maintains the brake hydraulic pressure to the 4 wheels, in order to momentarily prevent the vehicle from descending backward. | |
| Brake Control (Operating Dynamic Radar Cruise Control System)*1 | When the driving support ECU assembly determines that a large amount of deceleration is required based on the distance to the preceding vehicle and the relative vehicle speed during the dynamic radar cruise control system operation, the skid control ECU operates the brake system according to the signal from the driving support ECU assembly. | |
| Brake Control (Operating Pre-crash Safety System)*2 | When the driving support ECU assembly determines a high possibility of collision, the skid control ECU activates the pre-crash brake assist or the pre-crash brake according to the signal from the driving support ECU assembly. | |
| Motive Force Control during TRC or VSC Operation | Transmits a motive force control signal from the skid control ECU to the power management control ECU to limit the motive force while the TRC or VSC is being activated. | |
FAIL-SAFE
Brake System
When the brake actuator stops, the switching solenoid valves SSC and SCC close and the switching solenoid valves SMC and SRC open. Thus, the fluid pressure generated in the hydraulic brake booster by the driver's brake pedal operation is directly supplied to each of the wheel cylinders.
| *1 | Reservoir Tank | *2 | Brake Fluid Level Warning Switch |
| *3 | Accumulator | *4 | Pump Motor |
| *5 | Pressure Relief Valve | *6 | Hydraulic Brake Booster |
| *7 | Stroke Simulator | *8 | Switching Solenoid Valve SSC |
| *9 | Master Cylinder Pressure Sensor | *10 | Accumulator Pressure Sensor |
| *11 | Switching Solenoid Valve SMC | *12 | Switching Solenoid Valve SRC |
| *13 | Pressure Control Solenoid Valve SLA | *14 | Front Wheel Cylinder Pressure Sensor |
| *15 | Switching Solenoid Valve SCC | *16 | Pressure Control Solenoid Valve SLR |
| *17 | Pressure Holding Solenoid Valve FLH | *18 | Pressure Holding Solenoid Valve FRH |
| *19 | Pressure Holding Solenoid Valve RLH | *20 | Pressure Holding Solenoid Valve RRH |
| *21 | Pressure Reduction Solenoid Valve FLR | *22 | Pressure Reduction Solenoid Valve FRR |
| *23 | Pressure Reduction Solenoid Valve RLR | *24 | Pressure Reduction Solenoid Valve RRR |
| *25 | Front Left Wheel Cylinder | *26 | Front Right Wheel Cylinder |
| *27 | Rear Left Wheel Cylinder | *28 | Rear Right Wheel Cylinder |
| *29 | Brake Actuator | - | - |
| Item | System Off | |
|---|---|---|
| Pressure Control Solenoid Valve | SLA | Off (Close) |
| SLR | Off (Close) | |
| Switching Solenoid Valve | SSC | Off (Close) |
| SCC | Off (Close) | |
| SMC | Off (Open) | |
| SRC | Off (Open) | |
| Pressure Holding Solenoid Valve | FLH | Off (Open) |
| FRH | Off (Open) | |
| RLH | Off (Open) | |
| RRH | Off (Open) | |
| Pressure Reduction Solenoid Valve | FLR | Off (Close) |
| FRR | Off (Close) | |
| RLR | Off (Close) | |
| RRR | Off (Close) | |
When the accumulator pressure is not supplied due to a failure in the brake system, the skid control ECU closes the switching solenoid valves SSC and SCC and opens the switching solenoid valves SMC and SRC. At this time, the fluid pressure generated in the master cylinder of the hydraulic brake booster is supplied only to the front wheel cylinders.
| *1 | Reservoir Tank | *2 | Brake Fluid Level Warning Switch |
| *3 | Accumulator | *4 | Pump Motor |
| *5 | Pressure Relief Valve | *6 | Hydraulic Brake Booster |
| *7 | Stroke Simulator | *8 | Switching Solenoid Valve SSC |
| *9 | Master Cylinder Pressure Sensor | *10 | Accumulator Pressure Sensor |
| *11 | Switching Solenoid Valve SMC | *12 | Switching Solenoid Valve SRC |
| *13 | Pressure Control Solenoid Valve SLA | *14 | Front Wheel Cylinder Pressure Sensor |
| *15 | Switching Solenoid Valve SCC | *16 | Pressure Control Solenoid Valve SLR |
| *17 | Pressure Holding Solenoid Valve FLH | *18 | Pressure Holding Solenoid Valve FRH |
| *19 | Pressure Holding Solenoid Valve RLH | *20 | Pressure Holding Solenoid Valve RRH |
| *21 | Pressure Reduction Solenoid Valve FLR | *22 | Pressure Reduction Solenoid Valve FRR |
| *23 | Pressure Reduction Solenoid Valve RLR | *24 | Pressure Reduction Solenoid Valve RRR |
| *25 | Front Left Wheel Cylinder | *26 | Front Right Wheel Cylinder |
| *27 | Rear Left Wheel Cylinder | *28 | Rear Right Wheel Cylinder |
| *29 | Brake Actuator | - | - |
| Item | Power Supply Malfunction | |
|---|---|---|
| Pressure Control Solenoid Valve | SLA | Off (Close) |
| SLR | Off (Close) | |
| Switching Solenoid Valve | SSC | Off (Close) |
| SCC | Off (Close) | |
| SMC | Off (Open) | |
| SRC | Off (Open) | |
| Pressure Holding Solenoid Valve | FLH | Off (Open) |
| FRH | Off (Open) | |
| RLH | Off (Open) | |
| RRH | Off (Open) | |
| Pressure Reduction Solenoid Valve | FLR | Off (Close) |
| FRR | Off (Close) | |
| RLR | Off (Close) | |
| RRR | Off (Close) | |
When the skid control ECU detects a malfunction of the front brake system, it closes the switching solenoid valves SSC and SCC and opens the switching solenoid valves SMC and SRC. At this time, the fluid pressure generated in the regulator in the hydraulic brake booster by the driver's brake pedal operation is directly supplied to the rear wheel cylinders.
| *1 | Reservoir Tank | *2 | Brake Fluid Level Warning Switch |
| *3 | Accumulator | *4 | Pump Motor |
| *5 | Pressure Relief Valve | *6 | Hydraulic Brake Booster |
| *7 | Stroke Simulator | *8 | Switching Solenoid Valve SSC |
| *9 | Master Cylinder Pressure Sensor | *10 | Accumulator Pressure Sensor |
| *11 | Switching Solenoid Valve SMC | *12 | Switching Solenoid Valve SRC |
| *13 | Pressure Control Solenoid Valve SLA | *14 | Front Wheel Cylinder Pressure Sensor |
| *15 | Switching Solenoid Valve SCC | *16 | Pressure Control Solenoid Valve SLR |
| *17 | Pressure Holding Solenoid Valve FLH | *18 | Pressure Holding Solenoid Valve FRH |
| *19 | Pressure Holding Solenoid Valve RLH | *20 | Pressure Holding Solenoid Valve RRH |
| *21 | Pressure Reduction Solenoid Valve FLR | *22 | Pressure Reduction Solenoid Valve FRR |
| *23 | Pressure Reduction Solenoid Valve RLR | *24 | Pressure Reduction Solenoid Valve RRR |
| *25 | Front Left Wheel Cylinder | *26 | Front Right Wheel Cylinder |
| *27 | Rear Left Wheel Cylinder | *28 | Rear Right Wheel Cylinder |
| *29 | Brake Actuator | - | - |
| Item | When Front Brake Malfunction | |
|---|---|---|
| Pressure Control Solenoid Valve | SLA | Off (Close) |
| SLR | Off (Close) | |
| Switching Solenoid Valve | SSC | Off (Close) |
| SCC | Off (Close) | |
| SMC | Off (Open) | |
| SRC | Off (Open) | |
| Pressure Holding Solenoid Valve | FLH | Off (Open) |
| FRH | Off (Open) | |
| RLH | Off (Open) | |
| RRH | Off (Open) | |
| Pressure Reduction Solenoid Valve | FLR | Off (Close) |
| FRR | Off (Close) | |
| RLR | Off (Close) | |
| RRR | Off (Close) | |
Skid Control ECU
In the event of a malfunction of the ABS, the skid control ECU can control the EBD if the EBD works properly.
In the event of a malfunction of the ABS with EBD, the skid control ECU will illuminate the brake warning lights to alert the driver of the malfunction and will disable brake control system operation.
In the event of a malfunction of the TRC and/or VSC, the skid control ECU will disable the TRC and VSC operation.
If a communication malfunction occurs between the skid control ECU and the steering sensor, airbag sensor assembly (yawrate sensor or acceleration sensor) or power management control ECU, the skid control ECU will disable the TRC and VSC operation.
When the power management control ECU detects a Diagnostic Trouble Code (DTC), it will disable the TRC and VSC operation.
DIAGNOSIS
If the skid control ECU detects a malfunction in the brake control system (ABS with EBD, brake assist, TRC and VSC), then the ABS warning light, brake warning light/red (malfunction), brake warning light/yellow (minor malfunction) or slip indicator light will illuminate either individually or as a group according to the function in which the malfunction has been detected, to alert the driver of the malfunction.
At the same time, a Diagnostic Trouble Code (DTC) will be stored in memory.
This system has a sensor signal check (test mode) function.
For details of DTCs that are stored in skid control ECU memory and DTCs that are output through the sensor signal check functions, see the Repair Manual.