OPERATION
Motive Force Control during TRC or VSC Operation
During the TRC or VSC operation, the skid control ECU outputs the motive force control signal to the power management control ECU. Upon receiving this signal, the power management control ECU inhibits the motive force.
Normal Brake Operation (with Regenerative Brake Cooperative Control)
During normal braking, the switching solenoid valves SSC and SCC open and the switching solenoid valves SMC and SRC close, and thus the fluid pressure circuit from the hydraulic brake booster to each wheel cylinder is individually separated. Each of the wheel cylinder pressures can be increased, retained and decreased by controlling the pressure control solenoid valves SLA and SLR under this condition.
The skid control ECU calculates the braking force required by the driver in accordance with the signals received from the master cylinder pressure sensor and the brake pedal stroke sensor. Then, the skid control ECU calculates the regenerative brake force value out of the required brake force and transmits the calculated value to the power management control ECU. Upon receiving the value, the power management control ECU generates a regenerative brake force. At the same time, the power management control ECU transmits the actual regenerative brake force value to the skid control ECU. The skid control ECU controls the solenoid valves in order to cause the hydraulic brake system to generate a brake force value (which is obtained by subtracting the regenerative brake force from the brake force value required by the driver).
The skid control ECU calculates the target wheel cylinder pressure (equivalent to the brake force required by the driver) in accordance with the signals received from the master cylinder pressure sensor and the brake pedal stroke sensor. The skid control ECU compares the wheel cylinder pressure with the target wheel cylinder pressure. If the wheel cylinder pressure is lower than the target wheel cylinder pressure, the skid control ECU boosts the pressure in the brake actuator. Accordingly, the fluid pressure in the accumulator is fed into the wheel cylinder. Moreover, this operation is the same when the hydraulic brake force must be increased in order to effect cooperative control in accordance with the changes in the regenerative brake force.
| *1 | Reservoir Tank | *2 | Brake Fluid Level Warning Switch |
| *3 | Accumulator | *4 | Pump Motor |
| *5 | Pressure Relief Valve | *6 | Hydraulic Brake Booster |
| *7 | Stroke Simulator | *8 | Switching Solenoid Valve SSC |
| *9 | Master Cylinder Pressure Sensor | *10 | Accumulator Pressure Sensor |
| *11 | Switching Solenoid Valve SMC | *12 | Switching Solenoid Valve SRC |
| *13 | Pressure Control Solenoid Valve SLA | *14 | Front Wheel Cylinder Pressure Sensor |
| *15 | Switching Solenoid Valve SCC | *16 | Pressure Control Solenoid Valve SLR |
| *17 | Pressure Holding Solenoid Valve FLH | *18 | Pressure Holding Solenoid Valve FRH |
| *19 | Pressure Holding Solenoid Valve RLH | *20 | Pressure Holding Solenoid Valve RRH |
| *21 | Pressure Reduction Solenoid Valve FLR | *22 | Pressure Reduction Solenoid Valve FRR |
| *23 | Pressure Reduction Solenoid Valve RLR | *24 | Pressure Reduction Solenoid Valve RRR |
| *25 | Front Left Wheel Cylinder | *26 | Front Right Wheel Cylinder |
| *27 | Rear Left Wheel Cylinder | *28 | Rear Right Wheel Cylinder |
| *29 | Brake Actuator | - | - |
| Item | Normal Braking Increase Mode | |
|---|---|---|
|
*: The solenoid valve constantly regulates the opening amount of the valve in accordance with the conditions in order to control the fluid pressure. |
||
| Pressure Control Solenoid Valve | SLA | On (Half-open*) |
| SLR | Off (Close) | |
| Switching Solenoid Valve | SSC | On (Open) |
| SCC | On (Open) | |
| SMC | On (Close) | |
| SRC | On (Close) | |
| Pressure Holding Solenoid Valve | FLH | Off (Open) |
| FRH | Off (Open) | |
| RLH | Off (Open) | |
| RRH | Off (Open) | |
| Pressure Reduction Solenoid Valve | FLR | Off (Close) |
| FRR | Off (Close) | |
| RLR | Off (Close) | |
| RRR | Off (Close) | |
The skid control ECU calculates the target wheel cylinder pressure (equivalent to the brake force required by the driver) in accordance with the signals received from the master cylinder pressure sensor and the brake pedal stroke sensor. The skid control ECU compares the wheel cylinder pressure with the target wheel cylinder pressure. If they are equal, the skid control ECU controls the brake actuator in the hold state. Accordingly, the wheel cylinders will be held at a constant pressure.
| *1 | Reservoir Tank | *2 | Brake Fluid Level Warning Switch |
| *3 | Accumulator | *4 | Pump Motor |
| *5 | Pressure Relief Valve | *6 | Hydraulic Brake Booster |
| *7 | Stroke Simulator | *8 | Switching Solenoid Valve SSC |
| *9 | Master Cylinder Pressure Sensor | *10 | Accumulator Pressure Sensor |
| *11 | Switching Solenoid Valve SMC | *12 | Switching Solenoid Valve SRC |
| *13 | Pressure Control Solenoid Valve SLA | *14 | Front Wheel Cylinder Pressure Sensor |
| *15 | Switching Solenoid Valve SCC | *16 | Pressure Control Solenoid Valve SLR |
| *17 | Pressure Holding Solenoid Valve FLH | *18 | Pressure Holding Solenoid Valve FRH |
| *19 | Pressure Holding Solenoid Valve RLH | *20 | Pressure Holding Solenoid Valve RRH |
| *21 | Pressure Reduction Solenoid Valve FLR | *22 | Pressure Reduction Solenoid Valve FRR |
| *23 | Pressure Reduction Solenoid Valve RLR | *24 | Pressure Reduction Solenoid Valve RRR |
| *25 | Front Left Wheel Cylinder | *26 | Front Right Wheel Cylinder |
| *27 | Rear Left Wheel Cylinder | *28 | Rear Right Wheel Cylinder |
| *29 | Brake Actuator | - | - |
| Item | Normal Braking Holding Mode | |
|---|---|---|
| Pressure Control Solenoid Valve | SLA | Off (Close) |
| SLR | Off (Close) | |
| Switching Solenoid Valve | SSC | On (Open) |
| SCC | On (Open) | |
| SMC | On (Close) | |
| SRC | On (Close) | |
| Pressure Holding Solenoid Valve | FLH | Off (Open) |
| FRH | Off (Open) | |
| RLH | Off (Open) | |
| RRH | Off (Open) | |
| Pressure Reduction Solenoid Valve | FLR | Off (Close) |
| FRR | Off (Close) | |
| RLR | Off (Close) | |
| RRR | Off (Close) | |
The skid control ECU calculates the target wheel cylinder pressure (equivalent to the brake force required by the driver) in accordance with the signals received from the master cylinder pressure sensor and the brake pedal stroke sensor. The skid control ECU compares the wheel cylinder pressure with the target wheel cylinder pressure. If the wheel cylinder pressure is higher than the target wheel cylinder pressure, the skid control ECU reduces the pressure in the brake actuator. Accordingly, the pressure in the wheel cylinder decreases. Moreover, this operation is the same when the hydraulic brake force must be decreased in order to effect cooperative control in accordance with the changes in the regenerative brake force.
| *1 | Reservoir Tank | *2 | Brake Fluid Level Warning Switch |
| *3 | Accumulator | *4 | Pump Motor |
| *5 | Pressure Relief Valve | *6 | Hydraulic Brake Booster |
| *7 | Stroke Simulator | *8 | Switching Solenoid Valve SSC |
| *9 | Master Cylinder Pressure Sensor | *10 | Accumulator Pressure Sensor |
| *11 | Switching Solenoid Valve SMC | *12 | Switching Solenoid Valve SRC |
| *13 | Pressure Control Solenoid Valve SLA | *14 | Front Wheel Cylinder Pressure Sensor |
| *15 | Switching Solenoid Valve SCC | *16 | Pressure Control Solenoid Valve SLR |
| *17 | Pressure Holding Solenoid Valve FLH | *18 | Pressure Holding Solenoid Valve FRH |
| *19 | Pressure Holding Solenoid Valve RLH | *20 | Pressure Holding Solenoid Valve RRH |
| *21 | Pressure Reduction Solenoid Valve FLR | *22 | Pressure Reduction Solenoid Valve FRR |
| *23 | Pressure Reduction Solenoid Valve RLR | *24 | Pressure Reduction Solenoid Valve RRR |
| *25 | Front Left Wheel Cylinder | *26 | Front Right Wheel Cylinder |
| *27 | Rear Left Wheel Cylinder | *28 | Rear Right Wheel Cylinder |
| *29 | Brake Actuator | - | - |
| Item | Normal Braking Reduction Mode | |
|---|---|---|
|
*: The solenoid valve constantly regulates the opening amount of the valve in accordance with the conditions in order to control the fluid pressure. |
||
| Pressure Control Solenoid Valve | SLA | Off (Close) |
| SLR | On (Half-open*) | |
| Switching Solenoid Valve | SSC | On (Open) |
| SCC | On (Open) | |
| SMC | On (Close) | |
| SRC | On (Close) | |
| Pressure Holding Solenoid Valve | FLH | Off (Open) |
| FRH | Off (Open) | |
| RLH | Off (Open) | |
| RRH | Off (Open) | |
| Pressure Reduction Solenoid Valve | FLR | Off (Close) |
| FRR | Off (Close) | |
| RLR | Off (Close) | |
| RRR | Off (Close) | |
ABS with EBD Operation
Based on the signals received from the 4 speed sensors, the skid control ECU calculates each wheel speed and deceleration, and checks wheel slipping conditions. According to the slipping condition, the skid control ECU controls the pressure holding valve and pressure reduction valve in order to adjust the fluid pressure of each wheel cylinder in the following 3 modes: pressure reduction, pressure holding, and pressure increase modes.
| Not Activated | Normal Braking | - | - |
|---|---|---|---|
| Activated | Increase Mode | Holding Mode | Reduction Mode |
| Pressure Holding Solenoid Valve | OFF (Open) | ON (Close) | ON (Close) |
| Pressure Reduction Solenoid Valve | OFF (Close) | OFF (Close) | ON (Open) |
| Wheel Cylinder Pressure | Increase | Hold | Reduce |
Brake Assist Operation
In the event of emergency braking, the skid control ECU detects the driver's intention based on the speed of the pressure increase in the master cylinder determined by the master cylinder pressure sensor signal. If the skid control ECU judges the need for additional brake assist, the fluid pressure from the accumulator is directed to the wheel cylinder to apply a greater fluid pressure than the regulator.
| *1 | Reservoir Tank | *2 | Brake Fluid Level Warning Switch |
| *3 | Accumulator | *4 | Pump Motor |
| *5 | Pressure Relief Valve | *6 | Hydraulic Brake Booster |
| *7 | Stroke Simulator | *8 | Switching Solenoid Valve SSC |
| *9 | Master Cylinder Pressure Sensor | *10 | Accumulator Pressure Sensor |
| *11 | Switching Solenoid Valve SMC | *12 | Switching Solenoid Valve SRC |
| *13 | Pressure Control Solenoid Valve SLA | *14 | Front Wheel Cylinder Pressure Sensor |
| *15 | Switching Solenoid Valve SCC | *16 | Pressure Control Solenoid Valve SLR |
| *17 | Pressure Holding Solenoid Valve FLH | *18 | Pressure Holding Solenoid Valve FRH |
| *19 | Pressure Holding Solenoid Valve RLH | *20 | Pressure Holding Solenoid Valve RRH |
| *21 | Pressure Reduction Solenoid Valve FLR | *22 | Pressure Reduction Solenoid Valve FRR |
| *23 | Pressure Reduction Solenoid Valve RLR | *24 | Pressure Reduction Solenoid Valve RRR |
| *25 | Front Left Wheel Cylinder | *26 | Front Right Wheel Cylinder |
| *27 | Rear Left Wheel Cylinder | *28 | Rear Right Wheel Cylinder |
| *29 | Brake Actuator | - | - |
| Item | Normal Braking Increase Mode | Brake Assist Activated | |
|---|---|---|---|
|
*: The solenoid valve constantly regulates the opening amount of the valve in accordance with the conditions in order to control the fluid pressure. |
|||
| Pressure Control Solenoid Valve | SLA | On (Half-open*) | On (Half-open*) |
| SLR | Off (Close) | Off (Close) | |
| Switching Solenoid Valve | SSC | On (Open) | On (Open) |
| SCC | On (Open) | On (Open) | |
| SMC | On (Close) | On (Close) | |
| SRC | On (Close) | On (Close) | |
| Pressure Holding Solenoid Valve | FLH | Off (Open) | Off (Open) |
| FRH | Off (Open) | Off (Open) | |
| RLH | Off (Open) | Off (Open) | |
| RRH | Off (Open) | Off (Open) | |
| Pressure Reduction Solenoid Valve | FLR | Off (Close) | Off (Close) |
| FRR | Off (Close) | Off (Close) | |
| RLR | Off (Close) | Off (Close) | |
| RRR | Off (Close) | Off (Close) | |
TRC Operation
The fluid pressure stored in the accumulator is regulated by the switching solenoid valves and control solenoid valves to the required pressure. Thus, the wheel cylinders of the drive wheels are controlled in the following 3 modes: pressure reduction, pressure holding, and pressure increase modes to control the slippage of the drive wheels. The diagram below shows the hydraulic circuit in pressure increase mode when the TRC is activated. Each pressure holding solenoid valve and pressure reduction solenoid valve is turned on/off according to the ABS with EBD operation pattern.
| *1 | Reservoir Tank | *2 | Brake Fluid Level Warning Switch |
| *3 | Accumulator | *4 | Pump Motor |
| *5 | Pressure Relief Valve | *6 | Hydraulic Brake Booster |
| *7 | Stroke Simulator | *8 | Switching Solenoid Valve SSC |
| *9 | Master Cylinder Pressure Sensor | *10 | Accumulator Pressure Sensor |
| *11 | Switching Solenoid Valve SMC | *12 | Switching Solenoid Valve SRC |
| *13 | Pressure Control Solenoid Valve SLA | *14 | Front Wheel Cylinder Pressure Sensor |
| *15 | Switching Solenoid Valve SCC | *16 | Pressure Control Solenoid Valve SLR |
| *17 | Pressure Holding Solenoid Valve FLH | *18 | Pressure Holding Solenoid Valve FRH |
| *19 | Pressure Holding Solenoid Valve RLH | *20 | Pressure Holding Solenoid Valve RRH |
| *21 | Pressure Reduction Solenoid Valve FLR | *22 | Pressure Reduction Solenoid Valve FRR |
| *23 | Pressure Reduction Solenoid Valve RLR | *24 | Pressure Reduction Solenoid Valve RRR |
| *25 | Front Left Wheel Cylinder | *26 | Front Right Wheel Cylinder |
| *27 | Rear Left Wheel Cylinder | *28 | Rear Right Wheel Cylinder |
| *29 | Brake Actuator | - | - |
| Item | TRC not Activated | TRC Activated | |||
|---|---|---|---|---|---|
| Increase Mode | Holding Mode | Reduction Mode | |||
| Pressure Control Solenoid Valve | SLA | Off (Close) | On (Open) | On (Open) | On (Open) |
| SLR | Off (Close) | Off (Close) | Off (Close) | Off (Close) | |
| Switching Solenoid Valve | SSC | On (Open) | On (Open) | On (Open) | On (Open) |
| SCC | On (Open) | On (Open) | On (Open) | On (Open) | |
| SMC | Off (Open) | On (Close) | On (Close) | On (Close) | |
| SRC | Off (Open) | On (Close) | On (Close) | On (Close) | |
| Pressure Holding Solenoid Valve | FLH | Off (Open) | Off (Open) | On (Close) | On (Close) |
| FRH | Off (Open) | Off (Open) | On (Close) | On (Close) | |
| RLH | Off (Open) | On (Close) | On (Close) | On (Close) | |
| RRH | Off (Open) | On (Close) | On (Close) | On (Close) | |
| Pressure Reduction Solenoid Valve | FLR | Off (Close) | Off (Close) | Off (Close) | On (Open) |
| FRR | Off (Close) | Off (Close) | Off (Close) | On (Open) | |
| RLR | Off (Close) | Off (Close) | Off (Close) | Off (Close) | |
| RRR | Off (Close) | Off (Close) | Off (Close) | Off (Close) | |
VSC Operation
The VSC, by the way of solenoid valves, controls the fluid pressure that is stored in the accumulator and applies it to the brake wheel cylinder of each wheel in the following 3 modes: pressure reduction, pressure holding, and pressure increase modes. As a result, the tendency of front wheel skid or rear wheel skid is controlled.
In front wheel skid restraining control, the brakes of the front wheels and rear wheel of the inner circle of the turn are applied. Also, depending on whether the brake is on or off and the condition of the vehicle, there are circumstances in which the brake might not be applied to the wheels even if the wheel is targeted for braking. The diagram below shows the hydraulic circuit in pressure increase mode, as it controls a front wheel skid condition while the vehicle is making a right turn. In other operating modes, the pressure holding valve and the pressure reduction valve are turned on/off according to the ABS with EBD operation pattern.
| *1 | Reservoir Tank | *2 | Brake Fluid Level Warning Switch |
| *3 | Accumulator | *4 | Pump Motor |
| *5 | Pressure Relief Valve | *6 | Hydraulic Brake Booster |
| *7 | Stroke Simulator | *8 | Switching Solenoid Valve SSC |
| *9 | Master Cylinder Pressure Sensor | *10 | Accumulator Pressure Sensor |
| *11 | Switching Solenoid Valve SMC | *12 | Switching Solenoid Valve SRC |
| *13 | Pressure Control Solenoid Valve SLA | *14 | Front Wheel Cylinder Pressure Sensor |
| *15 | Switching Solenoid Valve SCC | *16 | Pressure Control Solenoid Valve SLR |
| *17 | Pressure Holding Solenoid Valve FLH | *18 | Pressure Holding Solenoid Valve FRH |
| *19 | Pressure Holding Solenoid Valve RLH | *20 | Pressure Holding Solenoid Valve RRH |
| *21 | Pressure Reduction Solenoid Valve FLR | *22 | Pressure Reduction Solenoid Valve FRR |
| *23 | Pressure Reduction Solenoid Valve RLR | *24 | Pressure Reduction Solenoid Valve RRR |
| *25 | Front Left Wheel Cylinder | *26 | Front Right Wheel Cylinder |
| *27 | Rear Left Wheel Cylinder | *28 | Rear Right Wheel Cylinder |
| *29 | Brake Actuator | - | - |
| Item | VSC not Activated | VSC Activated | |||
|---|---|---|---|---|---|
| Increase Mode | Holding Mode | Reduction Mode | |||
| Pressure Control Solenoid Valve | SLA | Off (Close) | On (Open) | On (Open) | On (Open) |
| SLR | Off (Close) | Off (Close) | Off (Close) | Off (Close) | |
| Switching Solenoid Valve | SSC | On (Open) | On (Open) | On (Open) | On (Open) |
| SCC | On (Open) | On (Open) | On (Open) | On (Open) | |
| SMC | Off (Open) | On (Close) | On (Close) | On (Close) | |
| SRC | Off (Open) | On (Close) | On (Close) | On (Close) | |
| Pressure Holding Solenoid Valve | FLH | Off (Open) | Off (Open) | On (Close) | On (Close) |
| FRH | Off (Open) | Off (Open) | On (Close) | On (Close) | |
| RLH | Off (Open) | On (Close) | On (Close) | On (Close) | |
| RRH | Off (Open) | Off (Open) | On (Close) | On (Close) | |
| Pressure Reduction Solenoid Valve | FLR | Off (Close) | Off (Close) | Off (Close) | On (Open) |
| FRR | Off (Close) | Off (Close) | Off (Close) | On (Close) | |
| RLR | Off (Close) | Off (Close) | Off (Close) | Off (Close) | |
| RRR | Off (Close) | Off (Close) | Off (Close) | On (Open) | |
In rear wheel skid restraining control, the brakes of the front and rear wheels on the outer circle of the turn are applied. Also, depending on whether the brake is on or off and the operating condition of the vehicle, there are circumstances in which the brake might not be applied to the wheels even if the wheel is targeted for braking. The diagram below shows the hydraulic circuit in pressure increase mode, as it controls a rear wheel skid condition while the vehicle is making a right turn. In other operating modes, the pressure holding valve and the pressure reduction valve are turned on/off according to the ABS with EBD operation patterns.
| *1 | Reservoir Tank | *2 | Brake Fluid Level Warning Switch |
| *3 | Accumulator | *4 | Pump Motor |
| *5 | Pressure Relief Valve | *6 | Hydraulic Brake Booster |
| *7 | Stroke Simulator | *8 | Switching Solenoid Valve SSC |
| *9 | Master Cylinder Pressure Sensor | *10 | Accumulator Pressure Sensor |
| *11 | Switching Solenoid Valve SMC | *12 | Switching Solenoid Valve SRC |
| *13 | Pressure Control Solenoid Valve SLA | *14 | Front Wheel Cylinder Pressure Sensor |
| *15 | Switching Solenoid Valve SCC | *16 | Pressure Control Solenoid Valve SLR |
| *17 | Pressure Holding Solenoid Valve FLH | *18 | Pressure Holding Solenoid Valve FRH |
| *19 | Pressure Holding Solenoid Valve RLH | *20 | Pressure Holding Solenoid Valve RRH |
| *21 | Pressure Reduction Solenoid Valve FLR | *22 | Pressure Reduction Solenoid Valve FRR |
| *23 | Pressure Reduction Solenoid Valve RLR | *24 | Pressure Reduction Solenoid Valve RRR |
| *25 | Front Left Wheel Cylinder | *26 | Front Right Wheel Cylinder |
| *27 | Rear Left Wheel Cylinder | *28 | Rear Right Wheel Cylinder |
| *29 | Brake Actuator | - | - |
| Item | VSC not Activated | VSC Activated | |||
|---|---|---|---|---|---|
| Increase Mode | Holding Mode | Reduction Mode | |||
| Pressure Control Solenoid Valve | SLA | Off (Close) | On (Open) | On (Open) | On (Open) |
| SLR | Off (Close) | Off (Close) | Off (Close) | Off (Close) | |
| Switching Solenoid Valve | SSC | On (Open) | On (Open) | On (Open) | On (Open) |
| SCC | On (Open) | On (Open) | On (Open) | On (Open) | |
| SMC | Off (Open) | On (Close) | On (Close) | On (Close) | |
| SRC | Off (Open) | On (Close) | On (Close) | On (Close) | |
| Pressure Holding Solenoid Valve | FLH | Off (Open) | Off (Open) | On (Close) | On (Close) |
| FRH | Off (Open) | On (Close) | On (Close) | On (Close) | |
| RLH | Off (Open) | Off (Open) | On (Close) | On (Close) | |
| RRH | Off (Open) | On (Close) | On (Close) | On (Close) | |
| Pressure Reduction Solenoid Valve | FLR | Off (Close) | Off (Close) | Off (Close) | On (Open) |
| FRR | Off (Close) | Off (Close) | Off (Close) | Off (Close) | |
| RLR | Off (Close) | Off (Close) | Off (Close) | On (Open) | |
| RRR | Off (Close) | Off (Close) | Off (Close) | Off (Close) | |
Hill-start Assist Control Operation
Hill-start Assist Control helps maintain 4-wheel hydraulic pressure by operating the pressure control solenoid valve when the driver releases the brake pedal until depressing the accelerator pedal.
Based on the information provided by various sensors, switches, and the power management control ECU, the skid control ECU determines whether to activate Hill-start Assist Control.
| *1 | Reservoir Tank | *2 | Brake Fluid Level Warning Switch |
| *3 | Accumulator | *4 | Pump Motor |
| *5 | Pressure Relief Valve | *6 | Hydraulic Brake Booster |
| *7 | Stroke Simulator | *8 | Switching Solenoid Valve SSC |
| *9 | Master Cylinder Pressure Sensor | *10 | Accumulator Pressure Sensor |
| *11 | Switching Solenoid Valve SMC | *12 | Switching Solenoid Valve SRC |
| *13 | Pressure Control Solenoid Valve SLA | *14 | Front Wheel Cylinder Pressure Sensor |
| *15 | Switching Solenoid Valve SCC | *16 | Pressure Control Solenoid Valve SLR |
| *17 | Pressure Holding Solenoid Valve FLH | *18 | Pressure Holding Solenoid Valve FRH |
| *19 | Pressure Holding Solenoid Valve RLH | *20 | Pressure Holding Solenoid Valve RRH |
| *21 | Pressure Reduction Solenoid Valve FLR | *22 | Pressure Reduction Solenoid Valve FRR |
| *23 | Pressure Reduction Solenoid Valve RLR | *24 | Pressure Reduction Solenoid Valve RRR |
| *25 | Front Left Wheel Cylinder | *26 | Front Right Wheel Cylinder |
| *27 | Rear Left Wheel Cylinder | *28 | Rear Right Wheel Cylinder |
| *29 | Brake Actuator | - | - |
| Item | Hill-start Assist Control not Activated | Hill-start Assist Control Activated | ||
|---|---|---|---|---|
| Holding Mode | Reduction Mode | |||
| Pressure Control Solenoid Valve | SLA | Off (Close) | On (Open) | Off (Close) |
| SLR | Off (Close) | Off (Close) | On (Open) | |
| Switching Solenoid Valve | SSC | On (Open) | On (Open) | On (Open) |
| SCC | On (Open) | On (Open) | On (Open) | |
| SMC | Off (Open) | On (Close) | On (Close) | |
| SRC | Off (Open) | On (Close) | On (Close) | |
| Pressure Holding Solenoid Valve | FLH | Off (Open) | Off (Open) | Off (Open) |
| FRH | Off (Open) | Off (Open) | Off (Open) | |
| RLH | Off (Open) | Off (Open) | Off (Open) | |
| RRH | Off (Open) | Off (Open) | Off (Open) | |
| Pressure Reduction Solenoid Valve | FLR | Off (Close) | Off (Close) | Off (Close) |
| FRR | Off (Close) | Off (Close) | Off (Close) | |
| RLR | Off (Close) | Off (Close) | Off (Close) | |
| RRR | Off (Close) | Off (Close) | Off (Close) | |
Brake Control Operation (Operating Dynamic Radar Cruise Control) (Models with Dynamic Radar Cruise Control System)
The skid control ECU operates the brakes by receiving a motive force request signal from the driving support ECU assembly while the dynamic radar cruise control system is activated. This brake control operates in the same way as a normal brake operation.
Brake Control Operation (Operating Pre-crash Safety System) (Models with Pre-crash Safety System)
When the driver presses the brake pedal while the skid control ECU is switched to the brake assist standby mode, the brake assist control will operate even if the application of the brakes is not considered emergency braking. At this time, the brake control is performed in the same way as the normal brake assist operation.
If a collision is unavoidable, the skid control ECU actuates the motor in the power supply portion to apply direct pressure to the wheel cylinders even if the driver does not press the brake pedal. This brake control operates in the same way as a normal brake operation.
VSC (Cooperative Control with EPS) Operation
The operation of the solenoid valves under the cooperative control with EPS is the same as the operation of the brake control functions (ABS, TRC, VSC).