Home › Brake › BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS › BRAKE CONTROL SYSTEM › from 2015.04
NM2040EQ _54 Brake _014497 BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS _0073595 BRAKE CONTROL SYSTEM DE DETAILS F

BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS  BRAKE CONTROL SYSTEM  DETAILS  BRAKE PEDAL STROKE SENSOR  


CONSTRUCTION


a.

A non-contact type brake pedal stroke sensor is used.


b.

This sensor detects the extent of the brake pedal stroke and transmits it to the skid control ECU.

X126291E02
2.792,1.594 2.094,0.302 2.094,0.302 1.875,0.302 true 5.125,1.24 4.823,0.656 4.823,0.656 4.635,0.656 true 5.208,0.969 5.656,0.458 5.656,0.458 5.844,0.458 true 4.938,1.979 4.76,2.333 4.76,2.333 4.573,2.333 true 4.323,4.906 4.927,4.51 4.927,4.51 5.156,4.51 true 4.281,3.729 4.906,4.229 4.906,4.229 5.146,4.229 true 0.167,0.208 1.948,0.458 1.781,0.25 10 false Brake Pedal Stroke Sensor 3.813,0.594 4.719,0.792 0.906,0.198 10 false Sensor Shaft 5.896,0.396 6.854,0.625 0.958,0.229 10 false Return Spring 4.198,2.24 4.688,2.49 0.49,0.25 10 false Lever 4.948,2.698 6.469,2.958 1.521,0.26 10 false A-A Cross Section 2.198,1.125 2.313,1.292 0.115,0.167 10 true A 3.219,2.26 3.333,2.427 0.115,0.167 10 true A 1.917,3.094 2.51,3.344 0.594,0.25 10 false Voltage 2.063,3.417 2.563,3.698 0.5,0.281 10 false 4.5 V 2.167,4.813 2.667,5.094 0.5,0.281 10 false 1 V 2.052,5.031 2.5,5.313 0.448,0.281 10 false 0.4 V 2.167,5.26 2.5,5.469 0.333,0.208 10 false 0 V 2.594,5.292 3,5.573 0.406,0.281 10 false -9.7° 2.958,5.292 3.104,5.469 0.146,0.177 10 false 0 4.448,5.302 4.958,5.573 0.51,0.271 10 false 58.3° 4.854,5.323 6.823,5.667 1.969,0.344 10 false Sensor Lever Rotational Angle 5.208,4.135 5.813,4.417 0.604,0.281 10 false SKS1 5.219,4.438 5.823,4.719 0.604,0.281 10 false SKS2

HINT:
·

To install a brake pedal stroke sensor, which is available as a service part, perform as follows:

·

The sensor lever is secured with a pin to "0" stroke. (Do not detach the pin until the installation has been completed.)

·

In this state, install the sensor on the brake pedal (in the OFF state) on the vehicle.

·

After completing the installation, firmly press the brake pedal once to break off the pin that is securing the sensor in place.

·

Make sure the broken pin does not remain in the sensor lever.



·

After replacing the brake pedal stroke sensor, initialization of brake pedal stroke sensor must be performed on the skid control ECU side. For Details, refer to the Repair Manual.