Home › Brake › BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS › BRAKE CONTROL SYSTEM › from 2015.04
NM2040EQ _54 Brake _014497 BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS _0073595 BRAKE CONTROL SYSTEM GE GENERAL F

BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS  BRAKE CONTROL SYSTEM  GENERAL  GENERAL  


OUTLINE


a.

The brake actuator and the skid control ECU have been integrated and a hydraulic brake booster has been provided, thus optimizing the hydraulic circuit and offering a weight reduction.


b.

The brake control functions (ABS with EBD, Brake Assist, TRC, VSC and Hill-start Assist Control) are provided.


c.

A VSC that performs cooperative control with the EPS is used.


d.

An electronically controlled brake system is used to control the hydraulic pressure at each of the 4 wheels.


e.

Regenerative brake cooperative control is used.


f.

A VSC OFF switch is provided.



MAIN FEATURES


a.

Electronically Controlled Brake System

i.

In this system, the conventional brake booster portion has been discontinued. Instead, it consists of a hydraulic brake booster, brake actuator and brake booster pump assembly.


ii.

During normal braking, fluid pressure generated by the hydraulic brake booster does not directly actuate the wheel cylinders, but serves as a hydraulic pressure signal. Instead, the actual control pressure is obtained by regulating the fluid pressure of the brake booster pump assembly, which actuates the wheel cylinders.

X103420E17
5.052,5.854 4.49,7.021 4.49,7.021 4.406,7.021 true 2.542,0.792 3.375,0.156 3.375,0.156 3.458,0.156 true 5.865,5.177 5.615,5.177 5.615,5.177 5.385,5.656 true 4.51,2.615 6.635,2.938 2.125,0.323 10 false Power Steering ECU Assembly 4.479,3.625 6.646,4.063 2.167,0.438 10 false Power Management Control ECU 5.958,5.01 6.792,5.458 0.833,0.448 10 false Regenerative Brake Force 3.177,6.938 4.365,7.448 1.188,0.51 10 false Hydraulic Pressure Brake Force 4.99,7.396 5.833,7.656 0.844,0.26 10 false Brake Force 2.292,5.24 4.438,5.5 2.146,0.26 10 false Hydraulic Pressure Control Portion 0.479,5.24 1.833,5.604 1.354,0.365 10 false Hydraulic Pressure Power Source Portion 5.51,0.188 6.813,0.417 1.302,0.229 10 false : Electrical Signal 5.521,0.479 6.844,0.708 1.323,0.229 10 false : Fluid Pressure 0.5,2.594 2.198,2.865 1.698,0.271 10 false Skid Control ECU 1.583,1.51 2.635,1.979 1.052,0.469 10 false Master Cylinder Pressure Sensor 3.531,0.021 4.771,0.594 1.24,0.573 10 false Brake Pedal Stroke Sensor Assembly 0.49,3.042 2.865,3.479 2.375,0.438 10 false - Normal Brake, ABS with EBD, Brake Assist, TRC and VSC 0.49,3.74 3.104,4.083 2.615,0.344 10 false - Regenerative Brake Cooperative Control 0.5,4.229 3.146,4.479 2.646,0.25 10 false - Power Steering Cooperative Control 0.448,6.042 1.802,6.563 1.354,0.521 10 false - Generates hydraulic power using the pump 2.313,5.51 4.271,6.188 1.958,0.677 10 false Hydraulic pressure power is adjusted to the required braking force, and is distributed to each wheel 4.51,4.115 6.146,4.385 1.635,0.271 10 false - Regenerative Braking 4.521,2.927 5.583,3.24 1.063,0.313 10 false - Steering Assist


iii.

When a malfunction occurs in the brake system, the hydraulic brake booster supplies the fluid pressure (which is generated by the brake pedal effort) directly to the wheel cylinders.



b.

Regenerative Brake Cooperative Control

i.

Regenerative braking consists of a resistance force that is generated at the rotational axle in the reverse direction of the rotation of the generator (MG2) that is generating electricity. The greater the generated amperage (battery charging amperage), the greater the resistance force will be.

X101531C02
4.156,0.427 4.344,0.667 0.188,0.24 10 false *a 4.188,1.198 4.375,1.438 0.188,0.24 10 false *b 4.104,2.563 4.406,2.74 0.302,0.177 10 false *3 2.531,2.521 2.833,2.698 0.302,0.177 10 false *4 0.417,2.563 0.719,2.74 0.302,0.177 10 false *3 4.813,1.76 5.115,1.938 0.302,0.177 10 false *1 5.958,1.729 6.26,1.906 0.302,0.177 10 false *2 6.219,2.531 6.521,2.708 0.302,0.177 10 false *4 5.354,3.333 5.656,3.51 0.302,0.177 10 false *c 2.292,1.74 2.594,1.917 0.302,0.177 10 false *2 1.125,1.771 1.427,1.948 0.302,0.177 10 false *1 0.448,0.479 0.677,0.688 0.229,0.208 10 false *a 0.448,1.198 0.677,1.406 0.229,0.208 10 false *b 1.656,3.333 1.885,3.542 0.229,0.208 10 false *c
*1 MG1 *2 Inverter
*3 Engine *4 MG2
*a Rotating direction of electricity generation *b Resistance
*c Brake Force - -



ii.

The drive wheels and MG2 are joined mechanically. When the drive wheels rotate MG2 and cause it to operate as a generator, the regenerative brake force of MG2 is transmitted to the drive wheels. Based on the signals from the skid control ECU, this force is controlled by the hybrid system, which controls the generation of electricity.


iii.

The regenerative brake cooperative control does not rely solely on the braking force of the hydraulic brake system to supply the brake force required by the driver. Instead, by effecting cooperative control with the hybrid system, this control provides a joint braking force provided by regenerative braking and hydraulic braking. As a result, this control minimizes the loss of kinetic energy associated with normal hydraulic braking, and recovers energy by converting it into electrical energy.


iv.

The apportioning of brake force between hydraulic braking and regenerative braking varies according to vehicle speed and time.


v.

The apportioning of brake force between hydraulic braking and regenerative braking is accomplished by controlling the hydraulic braking so that the total brake force of the hydraulic braking and the regenerative braking matches the brake force required by the driver.


vi.

If the regenerative braking becomes inoperative due to a malfunction in the hybrid system, the brake system effects control so that the entire brake force required by the driver is supplied by the hydraulic brake system.

X101475E10
2.542,0.167 2.677,0.167 2.677,0.167 3.344,1.188 true 4.594,0.854 4.448,0.854 4.448,0.854 4.229,1.125 true 1.375,0.938 1.885,1.385 0.51,0.448 10 false Braking Force 1.333,0.073 2.563,0.521 1.229,0.448 10 false Hydraulic Pressure Braking Force 4.667,0.719 5.75,1 1.083,0.281 10 false Driver's Demand 3.646,2.188 4.542,2.625 0.896,0.438 10 false Regenerative Braking Force 4.646,2.875 5.042,3.115 0.396,0.24 10 false Time 2.188,3.229 4.823,3.583 2.635,0.354 10 false Changes in Braking Force Apportionment



c.

VSC

i.

In previous models, the brake control functions (ABS, TRC, VSC) and the Electronic Power Steering (EPS) were controlled individually. In contrast, new models use VSC, which utilizes a cooperative control with EPS. This system effects control of the brake control functions and the EPS in accordance with driving conditions. Thus, it realizes dynamic performance of the vehicle's ability to "run, turn and stop" and ensures excellent driving stability and drivability.

X104970E10
2.833,0.271 4.813,0.604 1.979,0.333 10 false - Steering Angle Signal 2.833,0.604 5.813,0.938 2.979,0.333 10 false - Yawrate Signal 2.833,0.99 5.688,1.323 2.854,0.333 10 false - Master Cylinder Pressure Signal 3.615,1.792 5.354,1.948 1.74,0.156 10 false Various Sensor Signals 4.625,2.125 6.698,2.448 2.073,0.323 10 false Power Steering ECU Assembly 1.229,2.281 3.01,2.708 1.781,0.427 10 false Actual Locus of Travel (Front Wheel Skid Tendency) 2.51,2.979 3.354,3.719 0.844,0.74 10 false Locus of Travel Based on the Target Yaw Rate 1.323,5.542 2.229,5.813 0.906,0.271 10 false Brake Control 3.969,2.729 5.24,3.125 1.271,0.396 10 false Power Management Control ECU 3.802,3.792 4.948,4.219 1.146,0.427 10 false Motive Force Control Command 5.135,3.781 6.552,4.302 1.417,0.521 10 false Steering Torque Assist Control Command 4.271,4.698 6,5.01 1.729,0.313 10 false Control Volume Calculation 3.302,5.448 4.885,5.938 1.583,0.49 10 false Four Wheel Independent Brake Control Command 5.198,5.438 6.802,5.927 1.604,0.49 10 false Vehicle Driving Condition Detection and Calculation 4.594,6.26 6,6.573 1.406,0.313 10 false Skid Control ECU 2.844,1.375 5.698,1.708 2.854,0.333 10 false - Throttle Position Signal




PRECAUTION


a.

When a brake control system is activated, the brake pedal may shudder, which is a normal occurrence of the system in operation and should not be considered a malfunction.