Home › Audio / Visual / Telematics › PARK ASSIST / MONITORING › BLIND SPOT MONITOR SYSTEM › from 2015.04
NM2040EQ _56 Audio / Visual / Telematics _014506 PARK ASSIST / MONITORING _0073608 BLIND SPOT MONITOR SYSTEM CO CONTROL F

PARK ASSIST / MONITORING  BLIND SPOT MONITOR SYSTEM  CONTROL  BLIND SPOT MONITOR CONTROL  


FUNCTION OF MAIN COMPONENTS


Component Function
Blind Spot Monitor Sensor LH and RH
·

Outputs millimeter waves from the blind spot monitor sensor to the blind spot sensor detection area, uses the reflected millimeter waves for detecting the presence of a vehicle, the vehicle-to-vehicle distance, and the relative speed, and then transmits this information to the built-in signal processing circuit.

·

The signal processing circuit determines if a vehicle is present, and illuminates or blinks the outer rear view mirror indicator light accordingly.

·

Dims the outer rear view mirror indicator light on the outer rear view mirror assembly.


Blind Spot Monitor Main Switch (Warning Canceling Switch Assembly) Pressing the blind spot monitor main switch (warning canceling switch assembly) turns the blind spot monitor system on or off.
Blind Spot Monitor Main Switch (Warning Canceling Switch Assembly) Blind Spot Monitor ON/OFF Indicator Light Illuminates when the blind spot monitor system is on.
Outer Rear View Mirror Assembly LH and RH Outer Rear View Mirror Indicator Light
·

Illuminates to inform the driver that a vehicle has been detected in the blind spot detection area.

·

Flashes to inform the driver when the turn signal lever is operated if a vehicle has been detected in the blind spot detection area.

·

Flashes to inform the driver that a vehicle has been detected in the blind spot detection area while the vehicle is reversing.


Combination Meter Assembly Transmits the turn switch signal to the blind spot monitor sensor LH and RH.
Combination Meter Assembly Multi-information Display When a malfunction is detected in the blind spot monitor sensors or the blind spot monitor sensors determine that control is not possible, a message is displayed on the multi-information display to warn the driver.
Steering Sensor Transmits the steering angle signal to the blind spot monitor sensor LH and RH.
Brake Booster with Master Cylinder Assembly
·

Skid Control ECU


Transmits the vehicle speed signal to the blind spot monitor sensor LH and RH.
Main Body ECU (Multiplex Network Body ECU)
·

Transmits the destination signal to the blind spot monitor sensor LH and RH.

·

Transmits the illumination signal to the blind spot monitor sensor LH and RH.

·

Transmits the dimmer signal to the blind spot monitor sensor LH and RH.


Outer Mirror Control ECU Assembly LH and RH Transmits the indicator light signal to the outer rear view mirror assembly.
RCTA Buzzer (Blind Spot Monitor Buzzer) Sounds when a vehicle is detected in the blind spot monitor sensor detection area while the driver is reversing.
Power Management Control ECU
·

Transmits the reverse signal to the blind spot monitor sensor LH and RH.

·

Transmits data between the CAN V bus and the CAN sub bus 11.




SYSTEM CONTROL


a.

The blind spot monitor system operates when all of the following conditions are met:

i.

The blind spot monitor main switch (warning canceling switch assembly) is on.


ii.

The shift lever is in a position other than R.


iii.

The vehicle speed is greater than about 16 km/h (10 mph).



b.

The blind spot monitor system can detect vehicles in its detection areas.

i.

The detection areas formed by the blind spot monitor sensor LH and RH are as shown below.

Y110644C01
2.854,0.292 3.083,0.479 0.229,0.188 10 *b 1.948,1.01 2.177,1.198 0.229,0.188 10 *a 1.948,2.563 2.177,2.75 0.229,0.188 10 *a 5.031,1.552 5.26,1.74 0.229,0.188 10 *d 5.042,2.146 5.271,2.333 0.229,0.188 10 *d 3.479,0.281 3.708,0.469 0.229,0.188 10 *c 2.906,3.396 3.135,3.583 0.229,0.188 10 *b 3.479,3.375 3.708,3.563 0.229,0.188 10 *c
*a 3.5 m (11.5 ft) *b 3.0 m (9.8 ft)
*c 1 m (3.3 ft) *d 0.5 m (1.6 ft)
V100144

Detection Area - -



ii.

When this vehicle is overtaken by another vehicle in the adjacent lane.

Y110645C03
4.25,2.229 4.25,1.698 true 4.188,2.24 4.5,2.438 0.313,0.198 10 false *a
*a This Vehicle - -
V100135

Vehicle Speed (Fast)
V100136

Vehicle Speed (Slow)
V100144

Detection Area - -



iii.

When another vehicle enters the detection area of this vehicle due to a lane change.

Y110646C05
0.208,0.188 3.396,2.615 3.188,2.427 3.625,0.188 6.813,2.615 3.188,2.427 2.104,1.958 2.104,2.26 true 5.604,1.917 5.604,2.208 true 0.302,0.25 0.531,0.438 0.229,0.188 10 false *a 2.042,2.292 2.271,2.479 0.229,0.188 10 false *c 5.531,2.25 5.76,2.438 0.229,0.188 10 false *c 3.708,0.25 3.938,0.438 0.229,0.188 10 false *b
*a Other vehicle enters the detection area during lane change (merge in) (Type 1). *b Other vehicle enters the detection area during lane change (merge in) (Type 2).
*c This Vehicle - -
V100135

Motion direction of this vehicle
V100136

Motion direction of other vehicle
V100144

Detection Area - -




c.

The RCTA function operates when all of the following conditions are met:

i.

The blind spot monitor main switch (warning canceling switch assembly) is on.


ii.

The shift lever is in R.


iii.

The speed of this vehicle is less than approximately 8 km/h (5 mph).


iv.

Target vehicle's speed is between approximately 8 km/h (5 mph) and 28 km/h (18 mph).



d.

The RCTA function can detect vehicles in its detection areas.

i.

The system continuously measures the relative speed of an approaching vehicle and its distance. If it is determined that the approaching vehicle will cross the path of this vehicle, the Estimated Crossing Time (ECT) is calculated. When the ECT is 2.5 seconds or less, the system alerts the driver by flashing the outer rear view mirror indicator lights and sounding the blind spot monitor buzzer.

Y142884C01
4.021,0.688 4.188,0.229 4.188,0.229 4.333,0.229 true 3.281,1.531 3.208,0.927 3.208,0.927 3.073,0.927 true 1.708,1.542 1.635,0.938 1.635,0.938 1.5,0.938 true 4.354,0.135 4.667,0.292 0.313,0.156 10 false *a 2.875,0.823 3.188,0.979 0.313,0.156 10 false *b 1.292,0.833 1.604,0.99 0.313,0.156 10 false *c 3.615,2 3.927,2.156 0.313,0.156 10 false *d 2.917,2.313 3.229,2.469 0.313,0.156 10 false *e 3.198,2 3.51,2.156 0.313,0.156 10 false *f 1.792,2.313 2.104,2.469 0.313,0.156 10 false *f
*a This Vehicle *b Target Vehicle (Approximately 8 km/h (5 mph))
*c Target Vehicle (Approximately 28 km/h (18 mph)) *d Approximately 5.5 m (18.0 ft.)
*e Approximately 20 m (66 ft.) *f Target Detection Line
V100144

Alert Area - -



ii.

Normal Parking

Y129967C01
5.198,1.844 5.417,1.26 5.417,1.26 5.583,1.26 true 2.146,2.104 2.031,1.51 2.031,1.51 1.875,1.51 true 3.615,0.594 3.615,0.385 3.615,0.385 3.719,0.385 true 3.74,0.292 4.052,0.448 0.313,0.156 10 false *a 5.615,1.156 5.927,1.313 0.313,0.156 10 false *b 1.667,1.417 1.979,1.573 0.313,0.156 10 false *b
*a This Vehicle *b Target Vehicle
V100145

Alert Area - -




e.

According to operation conditions, the blind spot monitor system promotes safety confirmation by using the outer rear view mirror indicator light to inform the driver that another vehicle has entered the blind spot monitor sensor detection area of this vehicle.


f.

The outer rear view mirror indicator light informs the driver that a vehicle is present in the blind spot detection area by illuminating when the turn signal switch is not operated, and by flashing when a vehicle is present and the turn signal switch is operated.

Y172627E01
3.125,6.563 3.979,6.917 0.854,0.354 10 false CAN (V Bus) 5.604,6.833 6.667,7.271 1.063,0.438 10 false Steering Sensor 0.417,6.448 1.854,6.76 1.438,0.313 10 false - Vehicle Speed Signal 0.604,6.094 1.729,6.427 1.125,0.333 10 false Skid Control ECU 0.354,5.333 2.021,5.927 1.667,0.594 10 false Brake Booster with Master Cylinder Assembly 3.125,5.74 4.563,6.052 1.438,0.313 10 false - Reverse Signal 2.698,5.396 4.771,5.76 2.073,0.365 10 false Power Management Control ECU 5.469,5.75 6.906,6.063 1.438,0.313 10 false - Turn Light Signal 5.167,5.406 7.031,5.771 1.865,0.365 10 false Combination Meter Assembly 5.167,4.292 6.969,4.906 1.802,0.615 10 false - Blind Spot Monitor ON/OFF Indicator Light 5.146,3.24 6.948,3.885 1.802,0.646 10 false Blind Spot Monitor Main Switch (Warning Canceling Switch Assembly) 3.729,4.969 5.042,5.365 1.313,0.396 10 false CAN (Sub Bus 11) 3.26,2.865 3.958,3.396 0.698,0.531 10 false Local CAN 4.021,2.302 4.74,3.625 0.719,1.323 10 false Blind Spot Monitor Sensor RH 2.427,2.313 3.146,3.635 0.719,1.323 10 false Blind Spot Monitor Sensor LH 5.302,2.24 6.875,2.823 1.573,0.583 10 false Outer Mirror Control ECU Assembly (RH) 0.396,2.25 1.969,2.833 1.573,0.583 10 false Outer Mirror Control ECU Assembly (LH) 0.417,1.063 1.865,1.708 1.448,0.646 10 false Outer Rear View Mirror Indicator Light 5.344,1.063 6.792,1.708 1.448,0.646 10 false Outer Rear View Mirror Indicator Light 5.365,0.271 6.813,0.917 1.448,0.646 10 false Outer Rear View Mirror Assembly RH 0.479,0.292 1.927,0.938 1.448,0.646 10 false Outer Rear View Mirror Assembly LH


g.

According to operation conditions, the RCTA function promotes safety confirmation by using the outer rear view mirror indicator lights and blind spot monitor buzzer to inform the driver that another vehicle has entered the blind spot monitor sensor alert area of this vehicle.


h.

When this vehicle is reversing, if a vehicle enters the detection area of the blind spot monitor sensors and it is determined the vehicle will cross the path of this vehicle, the system alerts the driver by flashing the outer rear view mirror indicator lights and sounding the blind spot monitor buzzer.

Y172628E01
3.208,6.542 4.896,6.74 1.688,0.198 10 false CAN (V Bus) 5.604,6.833 6.688,7.229 1.083,0.396 10 false Steering Sensor 0.479,6.438 1.896,6.75 1.417,0.313 10 false - Vehicle Speed Signal 0.594,6.083 1.771,6.479 1.177,0.396 10 false Skid Control ECU 0.333,5.281 2,5.885 1.667,0.604 10 false Brake Booster with Master Cylinder Assembly 3.125,5.76 4.167,6.052 1.042,0.292 10 false - Reverse Signal 2.615,5.396 4.677,5.781 2.063,0.385 10 false Power Management Control ECU 0.323,3.917 1.927,4.615 1.604,0.698 10 false RCTA Buzzer (Blind Spot Monitor Buzzer) 5.177,4.271 6.979,4.927 1.802,0.656 10 false - Blind Spot Monitor ON/OFF Indicator Light 5.156,3.219 6.969,4.198 1.813,0.979 10 false Blind Spot Monitor Main Switch (Warning Canceling Switch Assembly) 3.771,4.979 5,5.313 1.229,0.333 10 false CAN (Sub Bus 11) 3.26,2.875 3.99,3.479 0.729,0.604 10 false Local CAN 4.031,2.323 4.74,3.521 0.708,1.198 10 false Blind Spot Monitor Sensor RH 2.448,2.333 3.156,3.531 0.708,1.198 10 false Blind Spot Monitor Sensor LH 5.292,2.229 6.865,2.927 1.573,0.698 10 false Outer Mirror Control ECU Assembly (RH) 0.427,2.24 2,2.938 1.573,0.698 10 false Outer Mirror Control ECU Assembly (LH) 0.448,1.063 1.875,1.708 1.427,0.646 10 false Outer Rear View Mirror Indicator Light 5.385,1.063 6.813,1.708 1.427,0.646 10 false Outer Rear View Mirror Indicator Light 5.427,0.281 6.854,0.927 1.427,0.646 10 false Outer Rear View Mirror Assembly RH 0.448,0.281 1.875,0.927 1.427,0.646 10 false Outer Rear View Mirror Assembly LH



DIAGNOSIS


a.

The blind spot monitor system is equipped with a diagnosis function that can display warning messages in the multi-information display. For details, refer to the Repair Manual.