FUNCTION OF MAIN COMPONENTS
| Component | Function | |
|---|---|---|
|
*: Models with 10-speaker system |
||
| Navigation Receiver Assembly | Receives and processes data from the built-in components, such as the touch-sensitive display panel which allows flick or drag operation, navigation computer, gyro sensor or GPS receiver and various components positioned in different parts of the vehicle, controlling the navigation system and providing various information and the operation status via the multi-display using images, voice and sounds. | |
| Major Components of Navigation Receiver Assembly | Multi-display Panel | ·
Displays a map screen or an operation screen based on image signals from the navigation computer. ·
Sends operation signals input via the touch-sensitive display panel to the navigation computer. |
| Navigation Computer | ·
Updates the vehicle position based on location information calculated from GPS information, vehicle speed signals, information from the built-in sensors and the shift status. ·
Applies the mark of the calculated vehicle position to the map data in the microSD card (disc player disc) and sends the data to the multi-display. ·
Sends voice guidance audio signals to the stereo component amplifier assembly. ·
Sends navigation information, such as directions and route guidance, to the combination meter assembly. |
|
| Gyro Sensor | Detects the vehicle's vertical axis rotation speed (yaw rate and rotation movement) and sends it to the navigation computer. | |
| GPS Receiver | Demodulates GPS information received by the navigation antenna assembly, calculates the vehicle position and sends the position signal to the navigation computer. | |
| microSD Card Slot | Interfaces with the microSD card (disc player disc), which contains map data, the navigation system control program, etc. | |
| microSD Card (Disc Player Disc) | Contains map data and the navigation system control program, etc. | |
| Navigation Antenna Assembly | Receives GPS signals from satellites in orbit around the Earth, at an altitude of approximately 20200 km (12600 miles), and sends them to the navigation receiver assembly. | |
| Parking Brake Switch Assembly | Sends the parking brake position signal to the navigation receiver assembly. | |
| Power Management Control ECU | Sends an R shift position signal to the engine room junction block assembly. | |
| Engine Room Junction Block Assembly | Sends an R shift position signal to the navigation receiver assembly. | |
| Window Glass Antenna Wire
·
AM ·
FM ·
DAB |
Receives radio broadcasting signals (AM/FM/DAB). | |
| No. 1 Amplifier Antenna Assembly | Amplifies radio broadcasting signals from the radio antenna and sends them to the navigation receiver assembly. | |
| Digital Audio Broadcasting Antenna Assembly | Amplifies DAB signals from the DAB antenna and sends them to the navigation receiver assembly. | |
| Steering Pad Switch Assembly | Sends operation signals from switches such as the volume switch, mode switch, 4 way switch, enter switch and back switch operation to the spiral cable with sensor sub-assembly. | |
| Spiral Cable with Sensor Sub-assembly | Sends operation signals from the steering pad switch assembly to the navigation receiver assembly. | |
| Roof Console Box Assembly | Houses the telephone microphone assembly. | |
| Telephone Microphone Assembly | Recognizes the user's voice and sends audio signals to the navigation receiver assembly. | |
| No. 1 Stereo Jack Adapter Assembly | Communicates with the navigation receiver assembly via a USB communication line when a USB memory device, portable audio player (USB type) or Apple product is connected. | |
| Combination Meter Assembly | ·
Sends vehicle speed signals to the navigation receiver assembly or stereo component amplifier. ·
Displays navigation information, such as directions and route guidance, sent from the navigation receiver assembly on the multi-information display. |
|
| Stereo Component Amplifier Assembly* | Amplifies audio signals sent from the navigation receiver assembly and sends them to the speakers. | |
FUNCTION
Navigation Screen
The navigation computer calculates the present position and direction of travel, then determines a route and calculates the driving distance based on the following information sources:
Map data in the microSD card (disc player disc)
Global Positioning System (GPS) satellites
Built-in gyro sensor
Vehicle speed signal
Reverse signal
Parking Blake signal
Radio Data System Traffic Message Channel (RDS-TMC) signal
The functions of the navigation screen are listed below.
| Item | Function | |
|---|---|---|
| Map Display | Map Scroll | Scroll operation on the map screen can be selected in the following 2 ways:
·
Flick/drag scrolling: Flick or drag in the direction that brings your desired location closer to the center of the map screen. ·
Point scrolling: Enables scrolling by connecting the touch points on the map screen. |
| Taillight-interlocked Map Color Change | Changes the color of the map screen that is displayed when the taillights are turned on. | |
| North Up / Heading Up | ·
If North Up is selected, regardless of the direction of vehicle travel, north is always up. ·
If Heading Up is selected, the direction of vehicle travel is always up. |
|
| 3D Display | Displays a 3-dimensional (3D) view of the map. | |
| Map Scale Display | Allows the map scale to be adjusted. | |
| Street Name Indication on Scrolled Map | Displays the street name and city name even when the map screen is being scrolled. | |
| Point of Interest Display | Displays selected types of points of interest as marks on the map. | |
| Multiple Display Function | Displays different mode screens on a screen that is split into 3 views or 2 views. | |
| Current Position Display Function | Displays the latitude, longitude and altitude of the current position based on the GPS signals being received. | |
| Route Guidance Demonstration | Demonstrates the route guidance to the destination. | |
| Route Trace | By saving a traveled route automatically or saving it manually upon reaching the destination, the routes can be displayed and retraced. | |
| RDS-TMC Display | Displays RDS-TMC icons, arrows, popup messages and indicators when RDS-TMC service is being received. | |
| Destination Search | Preset Destination Memory Search | Sets a pre-registered point as a destination point while driving. |
| Address Search | A destination can be set by city/town name. | |
| Point of Interest Search | A destination can be set in 4 ways:
·
Quick search ·
Preset search ·
Category search ·
Name search |
|
| Map Search | A destination can be set by using the cursor on the map screen. | |
| Previous Destination Search | A destination can be set using the destination list in which previously set destinations are stored. | |
| Intersection Search | By specifying 2 streets, the point at which they intersect is set as the destination point. | |
| Route Search | Multiple Route Search | Searches for multiple routes. |
| Search Condition Designation | ·
Searches for quick, short, and alternate routes. ·
Sets whether the following routes should be avoided during route search: ·
Highways ·
Toll Roads ·
Ferries ·
Unsealed Roads ·
4WD Tracks |
|
| Adds Waypoints | Adds waypoints along with the set route to set the pass points. | |
| Regulated Road Consideration | Performs searches which consider regulated roads. | |
| Traffic Congestion Information Consideration | Performs searches which consider traffic congestion information. | |
| Auto Avoid Traffic Search | Automatically changes to route to avoid heavy congestion. | |
| Auto Re-route Search | Performs automatic re-route search if the vehicle deviates from the set route. | |
| Guidance | Voice Guidance | Provides voice guidance about the distance and the direction of travel to a destination point based on road conditions and vehicle speed. |
| Next Turn Guidance | Provides guidance about the distance to the next turn and indicates the direction of the turn using an arrow. | |
| Lane Information Guidance | Provides lane information and indicates the lane to be driven in when the vehicle is on a multiple lane road. | |
| Signposts Display | Displays lane information similar to overhead road traffic signs on the top of the map screen. | |
| Real Highway/Motorway Junction Display | Displays the junction and signage in 3D in the vicinity of a major junction while driving. | |
| Route Status Information Display | Displays route items that the driver selects to display, such as the current vehicle speed or altitude, in the data fields at the corner of the map screen. Route data related to the destination or following way points also can be displayed. | |
| Route Progress Bar Display | Displays the progress made on the current route using the route progress bar to the left of the map screen. | |
| Others | Voice Recognition | Recognizes pre-programmed system commands spoken to operate the navigation system. |
Setup Screen
The settings for the functions of the multi-display are available from the setup screen.
| Item | Function |
|---|---|
|
*: PBAP non-compatible phone, or PBAP compatible phone with the automatic telephone number transfer function set to off. |
|
| General Settings | ·
The time zone, the on/off setting of daylight saving time can be changed. ·
The unit of measurement for fuel consumption can be changed. ·
The beep sound can be turned off. ·
The color of the screen buttons can be changed. ·
Keyboard layout can be changed. ·
Automatic return from the audio screen to the home screen after audio operation can be changed. ·
Animations can be set to on/off. ·
The opening image can be changed. ·
The screen off image can be changed. ·
Registered information (personal data) can be cleared. ·
The navigation system program can be updated. ·
Third party software information used in the navigation system, such as notices, can be displayed. |
| Home Screen Settings | The display items/area on the home screen can be changed. |
| Voice Settings | ·
The voice guidance volume can be adjusted or switched off. ·
Voice guidance during route guidance can be set. ·
Voice recognition prompts can be set. ·
Voice recognition prompt interruption can be set to on/off. |
| Display Settings | ·
Map Menu, Camera and Video screens can be adjusted. ·
Depending on the position of the headlight switch, the screen changes to day or night mode. |
| Bluetooth Settings | ·
Bluetooth devices can be registered. ·
Bluetooth devices can be deleted. ·
Bluetooth devices can be selected. ·
Bluetooth devices can be edited. ·
Bluetooth system settings can be changed: ·
Automatic connection to a Bluetooth device ·
Bluetooth device name ·
Bluetooth device PIN-code ·
Bluetooth device address ·
Display of Bluetooth device connection status ·
Bluetooth device profile |
| Phone Settings | ·
A Bluetooth phone can be registered or connected. ·
Telephone sound settings can be changed: ·
Ring Tone ·
Ring Tone Volume ·
Message Readout volume ·
SMS/MMS Incoming Tone ·
SMS/MMS Incoming Tone Volume ·
E-mail Incoming Tone ·
E-mail Incoming Tone Volume ·
In-call Volume ·
Contact/Call history settings can be changed: ·
Automatic contact/history transfer function settings when a PBAP compatible Bluetooth phone is connected ·
Contacts Update ·
Contacts Sorting ·
Favorites list registration ·
Contacts deletion from the favorites list ·
Contact image display ·
Call history deletion* ·
New contact addition to the contact list* ·
Contact list editing* ·
Contact deletion from the contact list* ·
Message function settings can be changed: ·
Message forwarding from cellular phones ·
Automatic message readout ·
SMS/MMS notification popup ·
E-mail notification popup ·
Vehicle signature on outgoing messages ·
Message read status on phone update ·
Incoming SMS/MMS display when an SMS/MMS message is received "Full Screen": The incoming SMS/MMS display screen is displayed and can be operated on the screen. "Drop-Down": A message is displayed on the upper side of the screen and can be operated only via the steering wheel switches. ·
Incoming E-mail display when an E-mail is received "Full Screen": The incoming E-mail display screen is displayed and can be operated on the screen. "Drop-Down": A message is displayed on the upper side of the screen and can be operated only via the steering wheel switches. ·
Display of messaging account names on the inbox tab ·
Telephone display settings can be changed: ·
Incoming call display ·
Display of the automatic contact/history transfer completion message |
| Audio Settings | ·
FM radio settings can be changed: ·
Radio text display on/off settings ·
DAB radio settings ·
iPod settings ·
Cover art settings can be changed. |
| Toyota Link | ·
The voice guidance volume can be adjusted or switched off. ·
The pop up reminder for cellular phone data usage can be set. |
| Vehicle Information | ·
Customizable vehicle settings can be changed. ·
TOYOTA park assist settings can be changed. ·
Back camera guide line settings can be changed. |
| Screen Off | The screen can be turned off. |
Fuel Consumption Screen
The fuel consumption screen is displayed as illustrated below. This screen has the display functions listed below.
| Item | Outline | |
|---|---|---|
| (1) | Clear Switch | Clears all past information. |
| (2) | Average Speed | Displays an average speed value that has been calculated by the combination meter assembly, which is based on the distance driven and time elapsed since the power switch was turned on (IG). |
| (3) | Elapsed Time | Displays an elapsed time value that has been calculated by the combination meter assembly, which is based on the time elapsed since the power switch was turned on (IG). |
| (4) | Cruising Range | Displays the approximate drivable distance. |
| (5) | Past Record Switch | Changes the screen to the fuel consumption Past Record (per trip) screen. |
| (6) | Energy Switch | Changes the screen to the energy monitor screen. |
| (7) | Average Fuel Consumption Per Minute | ·
Displays the value that has been calculated by the combination meter assembly, which is based on the driven distance and the volume of fuel consumed (fuel injection signal), since that the power switch was turned on (IG). ·
Displays the average fuel consumption for the last minute, or since clear was last selected. |
| (8) | Recovered Energy | ·
Indicates the recovered energy for 1 minute with "E" symbols. ·
The recovered energy status is calculated by the power management control ECU. |
| (9) | Current Fuel Consumption | Displays the instantaneous (current) fuel consumption value that has been calculated by the combination meter assembly, which is based on the driven distance and the volume of fuel consumed (fuel injection signal), since that the power switch was turned on (IG). |
| (10) | Best Fuel Consumption | Displays the best (most economical) per trip fuel consumption. |
| (11) | Average Fuel Consumption | Displays the average fuel consumption for this trip. |
| (12) | Trip Information Switch | Changes the screen to the fuel consumption average per minute screen. |
| (13) | Average Fuel Consumption Per Trip | ·
Displays the current record and the last 5 average per trip fuel consumption records or the current record and those since clear was last selected. ·
Starts calculating the average fuel consumption when the average fuel consumption displayed on the combination meter assembly is reset. |
| (14) | Update Switch | ·
Restarts calculation of the average fuel consumption value. ·
Sends the average fuel consumption reset signal to the combination meter assembly to update the graph. |
| (15) | Energy Monitor | Indicates the energy transmission direction, making it possible to confirm the current drive method (engine, motor or both), the power generation status by the engine and status of regenerative energy use.
·
The State Of Charge (SOC) of the battery can be checked on the meter. The meter shows the SOC in 8 levels. ·
Displays the energy monitor status that has been calculated by the power management control ECU. |
DIAGNOSIS
For details on the procedure required to enter the Service Menu screen, refer to the Repair Manual.