Home › Audio / Visual / Telematics › PARK ASSIST / MONITORING › TOYOTA PARKING ASSIST-SENSOR SYSTEM › from 2016.05
NM2040EQ _56 Audio / Visual / Telematics _014506 PARK ASSIST / MONITORING _0073605 TOYOTA PARKING ASSIST-SENSOR SYSTEM CO CONTROL F

PARK ASSIST / MONITORING  TOYOTA PARKING ASSIST-SENSOR SYSTEM  CONTROL  TOYOTA PARKING ASSIST-SENSOR CONTROL  


FUNCTION OF MAIN COMPONENTS


Component Function

*1: Models with multimedia system

*2: Models with navigation system

*3: Models with parking assist monitor system

Clearance Warning ECU Assembly
·

Judges the approximate distance between the vehicle and an obstacle based on signals from the No. 1 ultrasonic sensors. Output signals are sent to the combination meter assembly radio and display receiver assembly*1 and navigation receiver assembly*2.

·

Sounds the No. 1 clearance warning buzzer.


No. 1 Ultrasonic Sensor (4) Detects the distance between the vehicle and an obstacle.
No. 1 Clearance Warning Buzzer Sounds to inform the driver according to the distance to the obstacle.
Combination Meter Assembly
·

Multi-information Display


·

Displays the location of the obstacle and the approximate distance between the vehicle and the obstacle.

·

Displays an indication of a malfunction or freezing of a No. 1 ultrasonic sensor to inform the driver.


Radio and Display Receiver Assembly*1
·

Displays the location of an obstacle and the approximate distance between the vehicle and the obstacle.

·

Displays an indication of a malfunction or freezing of a No. 1 ultrasonic sensor to inform the driver.

·

The sound volume can be chosen on the setup screen for the TOYOTA parking assist-sensor system.

·

Transmits the setup signal for the TOYOTA parking assist-sensor system to the clearance warning ECU assembly.


Navigation Receiver Assembly*2
Back Sonar or Clearance Sonar Switch Assembly Operating this switch allows the operation of the TOYOTA parking assist-sensor system to be enabled or disabled.
Air Conditioning Amplifier Assembly Sends outside temperature information to the clearance warning ECU assembly to allow distance compensation for the No. 1 ultrasonic sensors.
Main Body ECU (Multiplex Network Body ECU) Sends model destination information (information to indicate the market the vehicle was built for) to the clearance warning ECU assembly.
Power Management Control ECU Sends the shift position signals to the clearance warning ECU assembly.
Rear Television Camera Assembly*3
·

Captures images of the area behind the vehicle.

·

The clearance sonar icon is superimposed on the captured image. Then, the image is sent to the navigation receiver assembly as video signals.




SYSTEM CONTROL


a.

Detection Area

i.

The detection area of the No. 1 ultrasonic sensor is as shown in the following illustration.


ii.

This detection area is applicable when positioning a 60 mm (2.36 in.) diameter pole parallel or perpendicular to the ground. The ranges vary depending on the measuring method and type of obstacle.

Y169223C02
1.042,0.5 1.354,0.656 0.313,0.156 10 false *a 5.865,0.74 6.177,0.896 0.313,0.156 10 false *b 1.979,2.792 2.292,2.948 0.313,0.156 10 false *c 5.031,2.781 5.344,2.938 0.313,0.156 10 false *d 1.115,3.74 1.427,3.896 0.313,0.156 10 false *e 1.552,4.448 1.865,4.604 0.313,0.156 10 false *f 5.865,3.719 6.177,3.969 0.313,0.25 10 false *g 4.958,4.469 5.271,4.625 0.313,0.156 10 false *f
*a Approximately 550 mm (21.7 in.) *b Approximately 840 mm (33.1 in.)
*c Approximately 500 mm (19.7 in.) *d Approximately 600 mm (23.6 in.)
*e Approximately 330 mm (13.0 in.) *f Approximately 100 mm (3.9 in.)
*g Approximately 510 mm (20.1 in.) - -




b.

The operating condition of each sensor differs according to its installed position as shown in the table below:

Installation Position Operating Condition
Front Corner
·

Power switch is on (IG).

·

System is activated.

·

Shift lever is in a position other than P or R.

·

Vehicle speed is approximately 10 km/h (6 mph) or less.


·

Power switch is on (IG).

·

System is activated.

·

Shift lever is in R.


Rear Corner
·

Power switch is on (IG).

·

System is activated.

·

Shift lever is in R.






DIAGNOSIS


a.

If a system malfunction is detected, the clearance warning ECU assembly stores Diagnostic Trouble Codes (DTCs) in its memory. For details, refer to the Repair Manual.