Home › Engine / Hybrid System › 2AR-FXE ENGINE CONTROL › SFI SYSTEM
RM2040EQ _51 Engine / Hybrid System _014691 2AR-FXE ENGINE CONTROL _0074871 SFI SYSTEM D

2AR-FXE ENGINE CONTROL  SFI SYSTEM  FREEZE FRAME DATA  


DESCRIPTION


The ECM records vehicle and driving condition information as freeze frame data the moment a DTC is stored. When troubleshooting, freeze frame data can be helpful in determining whether the vehicle was moving or stationary, whether the engine was warmed up or not, whether the air fuel ratio was lean or rich, as well as other data recorded at the time of a malfunction.

HINT:

If it is impossible to replicate the problem even though a DTC is detected, confirm the freeze frame data.



A306151E03
2.271,1.01 3.146,1.385 0.875,0.375 10 false 0.5 seconds 1.323,1 2.198,1.375 0.875,0.375 10 false 0.5 seconds 0.385,0.99 1.26,1.365 0.875,0.375 10 false 0.5 seconds 0.375,2.802 2.208,3.125 1.833,0.323 10 false Freeze frame data recorded 2.427,0.167 3.198,0.396 0.771,0.229 10 false DTC stored

The ECM records engine conditions in the form of freeze frame data every 0.5 seconds. Using the intelligent tester, 5 separate sets of freeze frame data can be checked.

·

3 data sets before the DTC was stored.

·

1 data set when the DTC was stored.

·

1 data set after the DTC was stored.


These data sets can be used to simulate the condition of the vehicle around the time of the occurrence the malfunction. The data may assist in identifying the cause of the malfunction, and judging whether it was temporary or not.




PENDING FREEZE FRAME DATA


HINT:

Pending freeze frame data is stored when a 2 trip DTC is first detected during the first trip.


a.

Connect the intelligent tester to the DLC3.


b.

Turn the power switch on (IG).


c.

Turn the tester on.


d.

Enter the following menus: Powertrain / Engine and ECT / DTC.

Powertrain > Engine and ECT > Trouble Codes
50001 234

e.

Select a DTC in order to display its pending freeze frame data.

HINT:
·

Pending freeze frame data is cleared when any of the following occurs.

·

Using the tester, the DTCs cleared.


·

The cable is disconnected from the negative (-) auxiliary battery terminal.


·

40 trips with the engine fully warmed up have been performed after returning to normal. (Pending freeze frame data will not be cleared by only returning the system to normal.)


·

With previous pending freeze frame data stored, if pending freeze frame data is newly stored when a 2 trip DTC is detected in the first trip, the old freeze frame data will be replaced with the new one of the newly detected DTC in the next trip.



A251781E20
0.156,0.104 6.896,0.594 6.74,0.49 10 false When a DTC is detected in both the first and second trips but the system returns to normal from the third trip (2 trip logic DTC): 0.156,1.625 1.073,1.802 0.917,0.177 10 false Power Switch 1.302,1.458 2.115,1.75 0.813,0.292 10 false On (IG) 1.302,1.844 1.552,2.021 0.25,0.177 10 false Off 0.156,2.583 1.198,2.896 1.042,0.313 10 false Pending Freeze Frame Data 1.333,2.5 1.781,2.698 0.448,0.198 10 false Stored 1.323,2.781 1.833,3.104 0.51,0.323 10 false Not Stored 0.125,3.708 1.135,4.438 1.01,0.729 10 false Freeze Frame Data 1.292,3.667 1.74,3.865 0.448,0.198 10 false Stored 0.365,4.729 1.75,4.938 1.385,0.208 10 false :Malfunction detected 0.365,5.031 2.083,5.24 1.719,0.208 10 false :Malfunction not detected 2.073,0.885 2.76,1.094 0.688,0.208 10 false (First Trip) 2.823,0.885 3.781,1.125 0.958,0.24 10 false (Second Trip) 3.781,0.885 4.74,1.125 0.958,0.24 10 false (Third Trip) 4.594,0.896 5.552,1.135 0.958,0.24 10 false (Fourth Trip) 1.302,3.938 1.813,4.26 0.51,0.323 10 false Not Stored

A251782E22
0.188,0.177 7.063,0.594 6.875,0.417 10 false When 2 trip DTC is first detected in the first trip and another 2 trip DTC is first detected in the second trip: 0.604,1.531 1.521,1.844 0.917,0.313 10 false Power Switch 1.781,1.365 2.302,1.583 0.521,0.219 10 false On (IG) 1.781,1.719 2.125,1.896 0.344,0.177 10 false Off 0.479,2.323 1.542,2.688 1.063,0.365 10 false Pending Freeze Frame Data A 0.479,3.271 1.542,3.635 1.063,0.365 10 false Pending Freeze Frame Data B 1.781,2.25 2.24,2.417 0.458,0.167 10 false Stored 1.781,3.156 2.24,3.323 0.458,0.167 10 false Stored 1.781,2.531 2.24,2.927 0.458,0.396 10 false Not Stored 1.781,3.448 2.24,3.844 0.458,0.396 10 false Not Stored 0.677,4.156 3.188,4.396 2.51,0.24 10 false :Pending malfunction A detected 0.677,4.615 3.188,4.854 2.51,0.24 10 false :Pending malfunction B detected 0.677,5.115 2.771,5.344 2.094,0.229 10 false :No malfunction detected 4.198,2.875 5.302,3.052 1.104,0.177 10 false Uploaded 2.635,0.719 3.333,1.031 0.698,0.313 10 false (First Trip) 3.542,0.719 4.677,0.99 1.135,0.271 10 false (Second Trip) 4.604,0.719 5.729,1.052 1.125,0.333 10 false (Third Trip) 5.521,0.719 6.719,1.052 1.198,0.333 10 false (Fourth Trip)



LIST OF FREEZE FRAME DATA


Refer to "Data List / Active Test" (See page Engine / Hybrid System>2AR-FXE ENGINE CONTROL>SFI SYSTEM>DATA LIST / ACTIVE TEST).