The ECM controls the engine water pump assembly by calculating the necessary amount of coolant flow based on engine coolant temperature, engine speed and vehicle speed information. The speed of the engine water pump assembly is controlled steplessly using a duty cycle signal sent from the ECM. This optimal control enhances warm-up performance and reduces cooling losses, thus reducing the specific fuel consumption of the engine. The ECM monitors the speed of the engine water pump assembly and stores a DTC when it determines that the engine water pump assembly rotates excessively based on the fact that the actual speed is higher than the target for a certain amount of time. (However, the MIL will not illuminate.)
| DTC No. | Detection Item | DTC Detection Condition | Trouble Area | MIL | Memory |
|---|---|---|---|---|---|
| P148F | Engine Coolant Pump Over Revolution | When both of the following conditions are met for 5 seconds or more (1 trip detection logic):
·
Engine water pump assembly duty ratio is 85% or higher. ·
Actual engine water pump assembly speed exceeds the target for a certain amount of time. |
·
Lack of engine coolant ·
Engine coolant leak ·
Engine water pump assembly |
- | DTC stored |
DTC P148F may be stored if the engine has continuously run with insufficient engine coolant. If the engine coolant is sufficient and DTC P148F recur when the vehicle is brought to the workshop, confirm whether engine coolant was added after the vehicle had been driven with insufficient engine coolant.
Read freeze frame data using the intelligent tester. The ECM records vehicle and driving condition information as freeze frame data the moment a DTC is stored. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, if the air fuel ratio was lean or rich, and other data from the time the malfunction occurred.
Connect the intelligent tester to the DLC3.
Turn the power switch on (IG).
Turn the tester on.
Enter the following menus: Powertrain / Engine and ECT / DTC.
Read the DTCs.
| Result | Proceed to |
|---|---|
| DTC P148F is output | A |
| DTC P148F and other DTCs are output | B |
If any DTCs other than P148F are output, troubleshoot those DTCs first.
A
B
Check that the engine coolant level is between the FULL and LOW lines.
Click hereEngine / Hybrid System>2AR-FXE COOLING>COOLING SYSTEM>ON-VEHICLE INSPECTION
| Result | Proceed to |
|---|---|
| Engine coolant level is below the LOW line | A |
| Engine coolant level is above the LOW line | B |
A
B
Check the areas around the engine and heater for engine coolant leaks.
Click hereEngine / Hybrid System>2AR-FXE COOLING>COOLING SYSTEM>ON-VEHICLE INSPECTION
No leaks.
If the engine oil is cloudy during the engine oil level gauge check, it means that engine coolant has entered the engine lubrication system.
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Fill the reservoir tank up to the FULL line with engine coolant.
Make sure not to add engine coolant when the engine is hot.
| Proceed to |
|---|
| NEXT |
NEXT
Repair any engine coolant leaks.
Add engine coolant and perform air bleeding after repair.
Click hereEngine / Hybrid System>2AR-FXE COOLING>COOLANT(for Engine)>REPLACEMENT
| Proceed to |
|---|
| NEXT |
NEXT
Connect the intelligent tester to the DLC3.
Turn the power switch on (IG).
Turn the tester on.
Clear the DTC.
Click hereEngine / Hybrid System>2AR-FXE ENGINE CONTROL>SFI SYSTEM>DTC CHECK / CLEAR
| Proceed to |
|---|
| NEXT |
NEXT
Perform repair indoors or in a workshop.
Connect the intelligent tester to the DLC3.
Turn the power switch on (IG).
Turn the tester on.
Put the engine in inspection mode (maintenance mode).
Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>INSPECTION MODE PROCEDURE
| Tester Display |
|---|
| Inspection Mode |
Start the engine.
Enter the following menus: Powertrain / Engine and ECT / Data List / All Data / Coolant Temp and Elec Water Pump Spd.
Display the Data List diagram.
| Tester Display |
|---|
| Coolant Temp |
| Elec Water Pump Spd |
Idle the engine for about 20 minutes and check Coolant Temp, Elec Water Pump Spd using the tester, and check the cooling fans.
| Result | Proceed to |
|---|---|
| One of the following conditions is met:
·
The engine coolant temperature becomes 95°C (203°F) or higher and the engine water pump assembly performs intermittent operation (5 seconds pause after 25 seconds operation). ·
The engine water pump assembly do not start operating even after the engine coolant temperature becomes 95°C (203°F) or higher.*1, *2 ·
The ECM voltage is 15 V or less, and the Data List item Elec Water Pump Spd reaches 6375 rpm. |
A |
| The cooling fans start operating after the engine coolant temperature becomes 95°C (203°F) or less and decrease in the engine coolant temperature is observed.*3 | B |
*1: Be careful when the cooling fans do not start operating even after the engine coolant temperature becomes 95°C (203°F) or higher because the engine coolant temperature increases rapidly. (Make sure to stop the engine if the engine coolant temperature becomes 105°C (221°F) or higher.)
*2: If the ECM voltage is 14 V or higher and the engine water pump assembly is run excessively due to insufficient coolant etc., the water pump motor speed will exceed 5000 rpm. Enter the following menus to check the voltage of the ECM: Powertrain / Engine and ECT / Data List / All Data / Battery Voltage.
Click hereEngine / Hybrid System>2AR-FXE ENGINE CONTROL>SFI SYSTEM>DATA LIST / ACTIVE TEST
*3: When the engine is warmed up, the cooling fans operate and the engine coolant temperature will decrease. After the cooling fans begin operating, the engine coolant temperature will stabilize between 88 to 95°C (190 to 203°F).
A
B
Replace the engine water pump assembly.
Click hereEngine / Hybrid System>2AR-FXE COOLING>WATER PUMP>REMOVAL
| Proceed to |
|---|
| NEXT |
NEXT
Fill the reservoir tank up to the FULL line with engine coolant.
Make sure not to add engine coolant when the engine is hot.
| Proceed to |
|---|
| NEXT |
NEXT
Perform repair indoors or in a workshop.
Connect the intelligent tester to the DLC3.
Turn the power switch on (IG).
Turn the tester on.
Clear the DTCs.
Click hereEngine / Hybrid System>2AR-FXE ENGINE CONTROL>SFI SYSTEM>DTC CHECK / CLEAR
Put the engine in inspection mode (maintenance mode).
Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>INSPECTION MODE PROCEDURE
| Tester Display |
|---|
| Inspection Mode |
Start the engine.
Enter the following menus: Powertrain / Engine and ECT / Data List / All Data / Coolant Temp and Elec Water Pump Spd.
| Tester Display |
|---|
| Coolant Temp |
| Elec Water Pump Spd |
Idle the engine for about 20 minutes and check Coolant Temp, Elec Water Pump Spd using the tester, and check the cooling fans.
The cooling fans start operating after the engine coolant temperature becomes 95°C (203°F) or less and decrease in the engine coolant temperature is observed.
| Proceed to |
|---|
| NEXT |
NEXT