Home › Engine / Hybrid System › 2AR-FXE ENGINE CONTROL › IGNITION SYSTEM
RM2040EQ _51 Engine / Hybrid System _014691 2AR-FXE ENGINE CONTROL _0074872 IGNITION SYSTEM G

2AR-FXE ENGINE CONTROL  IGNITION SYSTEM  ON-VEHICLE INSPECTION  


PROCEDURE

Hide 19100P 1. PERFORM SPARK TEST

a.

Check for DTCs.

Click hereEngine / Hybrid System>2AR-FXE ENGINE CONTROL>SFI SYSTEM>DTC CHECK / CLEAR

NOTICE:

If any DTC is output, perform troubleshooting procedures for that DTC.



b.

Remove the ignition coil assemblies and spark plugs.

Click hereEngine / Hybrid System>2AR-FXE ENGINE CONTROL>IGNITION COIL AND SPARK PLUG>REMOVAL


c.
A259028

Disconnect the 4 injector connectors.


d.

Set the vehicle to inspection mode. (Step 3)

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>INSPECTION MODE PROCEDURE


e.

Install the spark plug into the ignition coil assembly, and then connect the ignition coil connector. (Step 4)


f.
A259029

Ground the spark plug. (Step 5)


g.

Check that spark occurs at each spark plug while the engine is being cranked. (Step 6)

NOTICE:
·

Be sure to ground the spark plugs when checking them.

·

Do not crank the engine for more than 2 seconds.

Cranking will stop if the power switch is pushed again for models with cranking holding function.

·

If a spark plug has been struck or dropped, replace it.

·

If an ignition coil assembly has been struck or dropped, replace it.



HINT:

Repeat steps 3 to 6 for each spark plug and ignition coil assembly.

If spark does not occur for any cylinder, perform the following Inspect Ignition Coil and Spark Test procedure.



h.
A259028

Connect the 4 fuel injector connectors.


i.

Install the spark plugs and ignition coil assemblies.

Click hereEngine / Hybrid System>2AR-FXE ENGINE CONTROL>IGNITION COIL AND SPARK PLUG>INSTALLATION




Hide 19500 2.INSPECT IGNITION COIL AND SPARK TEST

HINT:

Perform "Inspection After Repair" after replacing the spark plug and ignition coil assembly.

Click hereEngine / Hybrid System>2AR-FXE ENGINE CONTROL>SFI SYSTEM>INITIALIZATION


a.

Check that the wire harness side connector of the ignition coil assembly is securely connected.

Result
Result Action
NG Connect securely
OK Go to next step


b.

Perform a spark test on each ignition coil assembly.

i.

Replace the ignition coil assembly with a known good one.


ii.

Set the vehicle to inspection mode.

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>INSPECTION MODE PROCEDURE


iii.

Perform the spark test again.

Result
Result Action
NG Go to next step
OK Replace ignition coil assembly



c.

Perform a spark test on each spark plug.

i.

Replace the spark plug with a known good one.


ii.

Set the vehicle to inspection mode.

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>INSPECTION MODE PROCEDURE


iii.

Perform the spark test again.

Result
Result Action
NG Inspect the ignition system.
Click here(Click here)
OK Replace spark plug



Hide 19100P 3.CHECK SPARK PLUG

NOTICE:
·

Do not use a wire brush for cleaning.

·

Do not adjust the electrode gap of a used spark plug.



HINT:

Perform "Inspection After Repair" after replacing the spark plug.

Click hereEngine / Hybrid System>2AR-FXE ENGINE CONTROL>SFI SYSTEM>INITIALIZATION


a.
I039522C15
0.802,1.917 1.073,1.948 false 0.646,1.844 0.896,2.031 0.25,0.188 10 false *a
*a Ground


Check the electrode using a megohmmeter:

i.

Using a megohmmeter, measure the insulation resistance.

Standard Insulation Resistance:
Tester Connection Condition Specified Condition
Spark plug (terminal part) - Body ground Always 10 MΩ or higher


HINT:
·

If the result is not as specified, clean the spark plug with a spark plug cleaner and measure the resistance again.

·

If a megohmmeter is not available, perform the following simple inspection instead.





b.
A126881

Alternative inspection method:

i.

Quickly accelerate the engine to 4000 rpm 5 times.



iii.

Visually check the spark plug.

If the electrode is dry, the spark plug is functioning properly. If the electrode is damp, proceed to the next step.



c.

Check the spark plug for any damage to its thread and insulator.

If there is any damage, replace the spark plug.

Recommended Spark Plug:
Manufacturer Spark Plug Type
DENSO FK16HR-A8



d.

Reference:

i.
A260264C05
1.75,1.135 2.042,0.448 2.042,0.448 2.167,0.448 false 1.729,1.281 1.469,1.698 1.469,1.698 1.385,1.698 false 2.198,0.375 2.385,0.531 0.188,0.156 10 false *1 0.688,1.115 0.875,1.271 0.188,0.156 10 false *a 1.198,1.635 1.385,1.792 0.188,0.156 10 false *2
*1 Iridium chip
*2 Platinum chip
*a Spark plug electrode gap


Check the spark plug electrode gap.

Maximum electrode gap for a used spark plug:

1.1 mm (0.0433 in.)


If the gap is more than the maximum, replace the spark plug.

NOTICE:

Never attempt to adjust the gap of a used plug.


Electrode gap for a new spark plug:

0.7 to 0.8 mm (0.0276 to 0.0315 in.)




e.
A296690

Clean the spark plugs.

If the electrode has traces of wet carbon, clean the electrode with a spark plug cleaner and then dry it.

Standard air pressure:

588 kPa (6.0 kgf/cm2, 85 psi)


Standard duration:

20 seconds or less


HINT:

Only use a spark plug cleaner when the electrode is free of oil. If the electrode has traces of oil, use gasoline to clean off the oil before using the spark plug cleaner.