Home › Engine / Hybrid System › HYBRID / BATTERY CONTROL › HYBRID CONTROL SYSTEM
RM2040EQ _51 Engine / Hybrid System _014692 HYBRID / BATTERY CONTROL _0074885 HYBRID CONTROL SYSTEM U

HYBRID / BATTERY CONTROL  HYBRID CONTROL SYSTEM  DATA LIST / ACTIVE TEST  


DATA LIST


NOTICE:
·

Some Data List values may vary significantly if there are slight differences in the environment in which the vehicle is operating when measurements are obtained. Variations may also occur due to aging of the vehicle. Due to these considerations, it is not always possible to provide definite values to be used for judgment of malfunctions. It is possible that a malfunction may be present even if measured values are within the reference range.

·

In the event of a problem with intricate symptoms, collect sample data from another vehicle of the same model operating under identical conditions in order to reach an overall judgment by comparing all the items in the Data List.



a.

Connect the intelligent tester to the DLC3.


b.

Turn the power switch on (IG).


c.

Turn the intelligent tester on.


d.

Enter the following menus: Powertrain / Hybrid Control / Data List.


e.

Check the results by referring to the following table.

HINT:
·

When reviewing Data List information, try to select only the specific Data List items related to the inspection being performed. If all items are selected when checking the Data List, the interval between updates for each item will be longer, resulting in delayed or incorrect data.

·

Using a custom list makes it possible to easily select smaller groups of related Data List items.

·

The following custom lists are available:

·

Primary

·

HV Battery

·

Electric Leakage

·

Boost/Lower Converter

·

High Voltage Charge

·

HV Transmission

·

Auxiliary Battery

·

Thermo Sensor

·

Drive Performance

·

Elec Shift Lever System




Powertrain > Hybrid Control > Data List
Tester Display Measurement Item Range Normal Condition Diagnostic Note
Engine Coolant Temp Engine coolant temperature/ Min.: -40°C (-40°F), Max.: 215°C (419°F) Cold start→Fully warmed up:
Gradually rises
After warming up:
75 to 100°C (167 to 212°F)
-
Engine Revolution Engine speed/ Min.: 0 rpm, Max.: 16383 rpm While idling after the engine is warmed up and inspection mode:
Approximately 900 rpm
While driving at a constant speed:
No significant fluctuation
-
Vehicle Spd Vehicle speed/ Min.: 0 km/h (0 mph), Max.: 255 km/h (158 mph) Vehicle stopped:
0 km/h (0 mph)
While driving at a constant speed:
No significant fluctuation
-
Engine Run Time Elapsed time after starting engine/ Min.: 0 s, Max.: 65535 s Elapsed time after starting engine After the power switch is turned on (READY), elapsed time from initial engine start until the power switch is turned off.
+B Auxiliary battery voltage/ Min.: 0.00 V, Max.: 65.53 V Constant:
10.00 to 15.00 V
Auxiliary battery condition
Accel Pedal Pos #1 Accelerator pedal position sensor No.1/ Min.: 0.0%, Max.: 100.0% Accelerator pedal depressed:
Changes with accelerator pedal pressure
Accelerator pedal sensor assembly
Accel Pedal Pos #2 Accelerator pedal position sensor No.2/ Min.: 0.0%, Max.: 100.0% Accelerator pedal depressed:
Changes with accelerator pedal pressure
Accelerator pedal sensor assembly
Ambient Temperature Ambient air temperature/ Min.: -40°C (-40°F), Max.: 215°C (419°F) Power switch on (IG):
Same as ambient air temperature
-
Intake Air Temperature Intake air temperature/ Min.: -40°C (-40°F), Max.: 140°C (284°F) Constant:
Same as ambient air temperature
-
DTC Clear Warm Up The number of times the engine is warmed up after clearing DTCs/ Min.: 0, Max.: 255 MIL OFF, engine coolant temperature increases from below 22°C (71.6°F) before starting the engine to above 70°C (158°F) after starting the engine:
Increases once
-
DTC Clear Run Distance Drive distance after clearing DTCs/ Min.: 0 km (0 mile), Max.: 65535 km (40723 mile) - -
DTC Clear Min Elapsed time after clearing DTCs/ Min.: 0 min, Max.: 65535 min - -
MIL on Engine Run Time Driving time after a malfunction occurs/ Min.: 0 min, Max.: 65535 min - -
MIL Status MIL status/ ON or OFF MIL ON: ON Constant ON: Repair in accordance with detected DTCs
MIL on Run Distance Travel distance after a malfunction occurs/ Min.: 0 km (0 mile), Max.: 65535 km (40723 mile) - -
Engine Code Engine code - P314 -
ECU Code ECU code - - -
Destination Destination - Q -
OBD Requirements OBD requirements - E-OBD -
MAP Intake manifold pressure/ Min.: 0 kPa, Max.: 255 kPa Power switch on (IG) or engine stopped:
Atmosphere pressure
Valued less than atmospheric pressure are indicated while the engine is running
Atmosphere Pressure Atmospheric pressure/ Min.: 0 kPa, Max.: 255 kPa Constant:
Atmosphere pressure
-
Number of Emission DTC The number of emission DTCs - - -
Ready Signal Power switch condition/ ON or OFF Power switch on (READY):
ON
-
Motor(MG2) Revolution MG2 revolution/ Min.: -32768 rpm, Max.: 32767 rpm While driving:
Varies depending on vehicle operating conditions
·

Hybrid vehicle transaxle assembly

·

Inverter with converter assembly


Motor(MG2) Torq MG2 torque/ Min.: -4096.00 Nm, Max.: 4095.87 Nm While driving:
Varies depending on vehicle operating conditions
·

Power management control ECU

·

Hybrid vehicle transaxle assembly

·

Inverter with converter assembly


M(MG2) Trq Exec Val MG2 torque execution value/ Min.: -4096.00 Nm, Max.: 4095.87 Nm After full-load acceleration with power switch on (READY) and engine stopped:
Less than +/-20% of MG2 torque
·

Power management control ECU

·

Hybrid vehicle transaxle assembly

·

Inverter with converter assembly


Generator(MG1) Rev MG1 revolution/ Min.: -32768 rpm, Max.: 32767 rpm During charge or discharge:
Varies depending on vehicle operating conditions
·

Hybrid vehicle transaxle assembly

·

Inverter with converter assembly


Generator(MG1) Torq MG1 torque/ Min.: -4096.00 Nm, Max.: 4095.87 Nm During charge or discharge:
Varies depending on vehicle operating conditions
·

Power management control ECU

·

Hybrid vehicle transaxle assembly

·

Inverter with converter assembly


G(MG1) Trq Exec Val MG1 torque execution value/ Min.: -4096.00 Nm, Max.: 4095.87 Nm One second after engine automatically starts with shift lever in P (Condition before engine start: Power switch on (READY), engine stopped, A/C fan speed high and headlights on):
Less than +/- 20% of MG1 torque
·

Power management control ECU

·

Hybrid vehicle transaxle assembly

·

Inverter with converter assembly


Regenerative Brake Torq MG1 regenerative braking execution torque/ Min.: -4096.0 Nm, Max.: 4095.0 Nm While braking:
Varies depending on vehicle operation conditions
·

Power management control ECU

·

Hybrid vehicle transaxle assembly

·

Inverter with converter assembly


Rqst Regen Brake Torq Requested MG1 regenerative braking torque/ Min.: -4096.0 Nm, Max.: 4095.0 Nm While braking:
Varies depending on vehicle operation conditions
·

Power management control ECU

·

Hybrid vehicle transaxle assembly

·

Inverter with converter assembly


Inverter Temp-(MG1) Generator inverter temperature/ Min.: 15°C (59°F), Max.: 150°C (302°F) Vehicle left for 1 day at an ambient temperature of 25°C (77°F):
15 to 35°C (59 to 95°F)
While driving at an ambient temperature of 25°C (77°F):
15 to 110°C (59 to 230°F)
Inverter with converter assembly
Inverter Temp-(MG2) Motor inverter temperature/ Min.: 15°C (59°F), Max.: 150°C (302°F) Vehicle left for 1 day at an ambient temperature of 25°C (77°F):
15 to 35°C (59 to 95°F)
While driving at an ambient temperature of 25°C (77°F):
15 to 110°C (59 to 230°F)
Inverter with converter assembly
Motor Temp No2 MG1 temperature/ Min.: -40°C (-40°F), Max.: 215°C (419°F) Vehicle left for 1 day at an ambient temperature of 25°C (77°F):
25°C (77°F)
While driving at an ambient temperature of 25°C (77°F):
25 to 100°C (77 to 212°F)
GMT terminal
Motor Temp No1 MG2 temperature/ Min.: -40°C (-40°F), Max.: 215°C (419°F) Vehicle left for 1 day at an ambient temperature of 25°C (77°F):
25°C (77°F)
While driving at an ambient temperature of 25°C (77°F):
25 to 90°C (77 to 194°F)
MMT terminal
Accelerator Degree Accelerator pedal depressed angle/ Min.: 0.0%, Max.: 100.0% Accelerator pedal depressed:
Changes with accelerator pedal pressure
Accelerator pedal sensor assembly
Request Power Request engine power/ Min.: 0 W, Max.: 655350 W While driving with the engine running:
Varies depending on vehicle operating conditions
·

Power management control ECU

·

ECM

·

Engine


Target Engine Rev Target engine speed/ Min.: 0 rpm, Max.: 65535 rpm While driving with the engine running:
Varies depending on vehicle operating conditions
·

Power management control ECU

·

ECM

·

Engine


Engine Rev (Sensor) Engine speed/ Min.: 0 rpm, Max.: 16383 rpm While idling after the engine is warmed up:
Approximately 1000 rpm
While driving at a constant speed:
No significant fluctuation
-
Total Distance Traveled Drive total distance/ Min.: 0 km (0 mile), Max.: 16777215 km (10425361 mile) - -
State of Charge (All Bat) HV battery state of charge/ Min.: 0.0%, Max.: 100.0% Constant:
0.0 to 100.0%
·

HV battery

·

Battery smart unit

·

Power management control ECU


Master Cylinder Ctrl Trq Master cylinder control torque/ Min.: -4096.0 Nm, Max.: 4095.0 Nm Brake pedal depressed:
Changes with the brake pedal pressure
Master cylinder pressure sensor
Power Resource VB HV battery voltage/ Min.: 0.0 V, Max.: 6553.5 V Power switch on (READY):
204.0 to 340.0 V
·

HV battery

·

Battery smart unit

·

Power management control ECU


Power Resource IB HV battery current/ Min.: -327.68 A, Max.: 327.67 A Power switch on (READY):
-200.00 to 200.00 A
·

HV battery

·

Power cable

·

Inverter with converter assembly

·

Battery current sensor

·

Air conditioning system


VL-Voltage before Boosting High voltage before it is boosted/ Min.: 0 V, Max.: 450 V Power switch on (READY):
Practically the same as the HV battery voltage
·

HV battery

·

Inverter with converter assembly


VH-Voltage after Boosting High voltage after it is boosted/ Min.: 0 V, Max.: 1000 V Engine revving up with shift lever in P:
After boosted voltage to below 650 V
Inverter with converter assembly
Boost Ratio Boost converter boost ratio/ Min.: 0.0%, Max.: 127.5% The pre-boost and the post boost voltages are equal:
0.0 to 10.0%
Inverter with converter assembly
Drive Condition ID Drive condition ID - Engine stopped: 0
Engine about to be stopped: 1
Engine about to be started: 2
Engine operated or operating: 3
·

Power management control ECU

·

ECM

·

Hybrid vehicle transaxle assembly


Shift Sensor Shift Pos Shift position/ P/R/N/D/B Matches currently selected shift position:
P, R, N, D or B
Shift lever position sensor
Crank Position Crankshaft position/ Min.: -128 °CA, Max.: 127 °CA - -
A/C Consumption Pwr A/C consumption power/ Min.: 0 W, Max.: 12750 W While the air conditioning system is operating: 0 to 5000 W Air conditioning system
Short Wave Highest Val Waveform voltage in leak detection circuit in battery smart unit/ Min.: 0.00 V, Max.: 4.98 V Left for 2 minutes in power switch on (READY), and pre-boost and post boost voltages are equal:
4.00 V or more
High voltage circuit
MG1 Control Mode MG1 control mode/ Min.: 0, Max.: 2 PWM: 0
Variable PWM: 1
Rectangular wave: 2
-
MG1 Carrier Frequency MG1 carrier frequency/ 0.75kHz/1.25kHz/2.50kHz/3.75kHz/5.00kHz/10.00kHz - -
MG2 Control Mode MG2 control mode/ Min.: 0, Max.: 2 PWM: 0
Variable PWM: 1
Rectangular wave: 2
-
MG2 Carrier Frequency MG2 carrier frequency/ 0.75kHz/1.25kHz/2.50kHz/3.75kHz/5.00kHz - -
Num of Current Code The number of current DTCs/ Min.: 0, Max.: 255 - -
Num of History Code The number of history DTCs/ Min.: 0, Max.: 255 - -
Check Mode Check Mode/ ON or OFF - -
Shift Sensor SW - P Shift lever position sensor/ ON or OFF Shift lever in P: ON
Shift lever in any position other than P: OFF
Shift lever position sensor
Shift Sensor SW - R Shift lever position sensor/ ON or OFF Shift lever in R: ON
Shift lever in any position other than R: OFF
Shift lever position sensor
Shift Sensor SW - N Shift lever position sensor/ ON or OFF Shift lever in N: ON
Shift lever in any position other than N: OFF
Shift lever position sensor
Shift Sensor SW - D Shift lever position sensor/ ON or OFF Shift lever in D: ON
Shift lever in any position other than D: OFF
Shift lever position sensor
Shift Sensor SW - B Shift lever position sensor/ ON or OFF Shift lever in B: ON
Shift lever in any position other than B: OFF
Shift lever position sensor
Shift Sensor SW - FD Shift lever position sensor/ ON or OFF Shift lever in D or B: ON
Shift lever in any position other than D or B: OFF
Shift lever position sensor
Shift Sensor SW - RV Shift lever position sensor/ ON or OFF Shift lever in R: ON
Shift lever in any position other than R: OFF
Shift lever position sensor
Shift Sensor SW - MJ Shift lever position sensor/ ON or OFF Shift lever in P, R, N, D or B: ON
Shift lever in any position other than P, R, N, D or B: OFF
Shift lever position sensor
Calculate Load Calculated load/ Min.: 0.0%, Max.: 100.0% Engine idling with warm engine, air conditioner off, shift lever in P and inspection mode selected:
20.0 to 40.0%
Engine speed of 2500 rpm, air conditioner off, shift lever in P and inspection mode selected:
15.0 to 35.0%
·

Air cleaner condition

·

Throttle valve status


Throttle Position Throttle position sensor/ Min.: 0.0%, Max.: 100.0% Throttle valve fully closed:
10.0 to 24.0%
Throttle valve status
DCDC Cnv Tar Pulse Duty Target auxiliary battery voltage/ Min.: 0.0%, Max.: 399.9% - -
Inverter Coolant Water Temperature Inverter coolant temperature/ Min.: -40°C (-40°F), Max.: 110°C (230°F) Cold start→Fully warmed up:
Gradually rises
System operating normally:
Controlled at 65°C (149°F) or less
·

Inverter with converter assembly

·

Inverter water pump assembly

·

Cooling fan system

·

Inverter cooling system

·

IGCT No.3 fuse


Cooling Fan 0 Cooling fan operating condition/ Min.: 0.0%, Max.: 127.5% - -
Inverter W/P Revolution Inverter water pump assembly speed/ Min.: 0 rpm, Max.: 15000 rpm Power switch on (READY):
1625 to 5875 rpm
·

Power management control ECU

·

Inverter water pump assembly


Prohibit DC/DC conv sig DC/DC converter prohibition signal/ ON or OFF Power switch on (IG):
ON (Prohibited)
Power switch on (READY):
OFF (Permitted)
·

Power management control ECU

·

DC/DC converter


EV Request EV mode transition availability/ ON or OFF In EV mode:
ON
-
TRC OFF Switch VSC condition/ OFF/TRC/TRC, VSC VSC OFF switch on:
OFF
-
Starter Switch Starter ON / OFF signal/ ON or OFF - -
Inv-T (MG1) aftr IG-ON Generator inverter temperature soon after power switch on (IG)/ Min.: 15°C (59°F), Max.: 150°C (302°F) - -
Inv-T (MG2) aftr IG-ON Motor inverter temperature soon after power switch on (IG)/ Min.: 15°C (59°F), Max.: 150°C (302°F) - -
Mtr-T (MG2) aftr IG-ON MG2 temperature soon after power switch on (IG)/ Min.: -40°C (-40°F), Max.: 215°C (419°F) - -
Conv-Tmp after IG-ON Boost converter temperature soon after power switch on (IG)/ Min.: 15°C (59°F), Max.: 150°C (302°F) - -
SOC after IG-ON HV battery state of charge soon after power switch on (IG)/ Min.: 0.0%, Max.: 127.5% - -
Inv-Temp (MG1) Max Generator inverter maximum temperature/ Min.: 15°C (59°F), Max.: 150°C (302°F) - -
Inv-Temp (MG2) Max Motor inverter maximum temperature/ Min.: 15°C (59°F), Max.: 150°C (302°F) - -
Mtr-Temp (MG2) Max MG2 maximum temperature/ Min.: -40°C (-40°F), Max.: 215°C (419°F) - -
Converter Temp Max Boost converter maximum temperature/ Min.: 15°C(59°F), Max.: 150°C (302°F) - -
Status of Charge Max Maximum status of charge/ Min.: 0.0%, Max.: 127.5% - -
Status of Charge Min Minimum status of charge/ Min.: 0.0%, Max.: 127.5% - -
Stop Light Switch Stop light switch assembly condition/ ON or OFF Brake pedal depressed:
ON
-
Auxiliary Batt Temperature Auxiliary battery temperature/ Min.: -40°C (-40°F), Max.: 215°C (419°F) Auxiliary battery temperature is 20°C (68°F):
20°C (68°F)
-
Collision Signal (Airbag) Detection of collision by airbag sensor assembly/ ON or OFF Collision detection by the airbag sensor assembly: -
TC Terminal TC terminal state/ ON or OFF TC terminal connected:
ON
-
Inter Lock Switch Interlock switch condition/ ON or OFF Power switch on (IG), connector cover assembly, UPR inverter cover, engine wire No. 4 (air conditioner wire) and service plug grip installed detached:
ON
-
EV Switch EV drive mode switch (pattern select switch assembly) condition/ ON or OFF EV drive mode switch (pattern select switch assembly) being pushed and held:
ON
-
Back Up Lamp Relay Back up light switch condition/ ON or OFF Shift lever in R
ON
-
ECO Mode ECO mode transition availability/ ON or OFF In ECO mode:
ON
·

Combination meter assembly

·

Power management control ECU


Generate Torque Generated drive torque/ Min.: -4096.0 Nm, Max.: 4095.8 Nm While driving:
Varies depending on vehicle operating conditions
-
Prohibit Charge for P Pos HV battery charge in shift lever in P prohibition state/ ON or OFF HV battery charge in shift lever in P prohibition:
ON
-
DC/DC Cnv Temp (Upper) Boost converter temperature (upper)/ Min.: 15°C (59°F), Max.: 150°C (302°F) Vehicle left for 1 day at an ambient temperature of 25°C (77°F):
15 to 35°C (59 to 95°F)
While driving at an ambient temperature of 25°C (77°F):
25 to 110°C (77 to 230°F)
Inverter with converter assembly
Safing Signal (Airbag) Safing state of the airbag sensor assembly/ ON or OFF When safing state of the airbag sensor assembly:
ON
-
DC/DC Cnv Temp (Lower) Boost converter temperature (lower)/ Min.: 15°C (59°F), Max.: 150°C (302°F) Vehicle left for 1 day at an ambient temperature of 25°C (77°F):
15 to 35°C (59 to 95°F)
While driving at an ambient temperature of 25°C (77°F):
25 to 121°C (77 to 250°F)
Inverter with converter assembly
Normal Signal for A/B ECU Control state of airbag sensor assembly/ ON or OFF When the airbag sensor assembly is operating normally:
ON
-
Mtr-T (MG1) aftr IG-ON MG1 temperature soon after power switch on (IG)/ Min.: -40°C (-40°F), Max.: 215°C (419°F) - -
Mtr-Temp (MG1) Max MG1 maximum temperature/ Min.: -40°C (-40°F), Max.: 215°C (419°F) - -
Overvoltage Input to Conv Boost converter overvoltage detection/ ON or OFF Overvoltage is received by the boost converter:
ON
Normal:
OFF
-
Overvoltage Input to Inv Inverter overvoltage detection/ ON or OFF Overvoltage is received by the inverter:
ON
Normal:
OFF
-
Emergency Shutdown Inverter emergency shutdown/ ON or OFF Inverter emergency shutdown:
ON
Normal:
OFF
-
MG1 Inverter Shutdown Generator inverter shutdown/ ON or OFF Generator inverter shutdown:
ON
Normal:
OFF
-
MG1 Inverter Fail Generator inverter failure/ ON or OFF Generator inverter faulty:
ON
Normal:
OFF
-
MG2 Inverter Shutdown Motor inverter shutdown/ ON or OFF Motor inverter shutdown:
ON
Normal:
OFF
-
MG2 Inverter Fail Motor inverter failure/ ON or OFF Motor inverter faulty:
ON
Normal:
OFF
-
Conv Shutdown Boost converter shutdown/ ON or OFF Boost converter shutdown:
ON
Normal:
OFF
-
Converter Fail Boost converter failure/ ON or OFF Boost converter faulty:
ON
Normal:
OFF
-
Internal Shift Position ECU internal shift condition/ P/R/N/D/B Matches currently selected shift position:
P, R, N, D or B
-
HV Start Condition Indicates the hybrid start condition/ Norml / Pr A/C / Remote - -
W/P Run Control Duty Inverter water pump motor driver request duty/ Min.: 0.00%, Max.: 100.00% Power switch on (READY):
62.50 to 81.25%
Power management control ECU
Engine Stop Request Engine stop request/ Request or No Requesting engine stop:
Request
·

ECM

·

Power management control ECU


Engine Idling Request Engine idling request/ Request or No Requesting idle:
Request
·

ECM

·

Power management control ECU


Main Batt Charging Rqst HV battery charging request/ Request or No Requesting HV battery charging:
Request
·

Battery smart unit

·

HV battery


Aircon Request Engine starting request from air conditioning amplifier assembly/ Request or No While an engine start is requested from the air conditioning amplifier assembly:
Request
air conditioning amplifier assembly
Engine Warming Up Rqst Engine warm-up request/ Request or No While an engine warm-up is requested:
Request
After the engine is warmed up:
No
·

Power management control ECU

·

ECM


SMRP Status Operating state of SMRP/ ON or OFF Immediately after the power switch on (ST-ON) state occurred:
ON
After the above timing:
OFF
Cannot be confirmed using the intelligent tester. Use an oscilloscope.
·

Hybrid battery junction block assembly

·

Wire harness


SMRB Status Operating state of SMRB/ ON or OFF Power switch on (READY):
ON
·

Hybrid battery junction block assembly

·

Wire harness


SMRG Status Operating state of SMRG/ ON or OFF Power switch on (READY):
ON
·

Hybrid battery junction block assembly

·

Wire harness


SMRP Control Status Commanded state of SMRP/ ON or OFF Immediately after the power switch on (ST-ON) state occurred:
ON
After the above timing:
OFF
Cannot be confirmed using the intelligent tester. Use an oscilloscope.
SMRB Control Status Commanded state of SMRB/ ON or OFF Power switch on (READY):
ON
-
SMRG Control Status Commanded state of SMRG/ ON or OFF Power switch on (READY):
ON
-
MG1 Gate Status MG1 gate status/ ON or OFF Shutting down generator inverter:
ON
Normal:
OFF
·

Power management control ECU

·

Inverter with converter assembly


MG2 Gate Status MG2 gate status/ ON or OFF Shutting down motor inverter:
ON
Normal:
OFF
·

Power management control ECU

·

Inverter with converter assembly


Converter Gate Status Boost converter gate status/ ON or OFF Shutting down boost converter:
ON
Normal:
OFF
·

Power management control ECU

·

Inverter with converter assembly


Aircon Gate Status While A/C inverter is being shut off/ ON or OFF While A/C inverter is being shut off:
ON
Normal:
OFF
·

Air conditioning amplifier assembly

·

Power management control ECU


Converter Carrier Freq Boost converter signal carrier frequency/ 9.55kHz/9.13kHz/8.71kHz/8.29kHz/7.87kHz/7.45kHz/4.8kHz - -
Delta SOC Difference between maximum and minimum values of SOC/ Min.: 0.0%, Max.: 127.5% READY indicator on, engine stopped and no electrical load:
0.0 to 60.0%
-
Batt Pack Current Val HV battery current/ Min.: -327.68 A, Max.: 327.67 A Immediately after a full-load acceleration with the engine stopped:
Maximum 190.00 A
Immediately after engine start with shift lever in P:
100.00 A or more
HV battery current sensor circuit
Inhaling Air Temp HV battery intake air temperature/ Min.: -50.0°C (-58°F), Max.: 205.9°C (402.6°F) - -
Auxiliary Battery Vol Auxiliary battery voltage/ Min.: -40.00 V, Max.: 39.99 V Same as auxiliary battery voltage
·

Auxiliary battery

·

Hybrid vehicle converter


Charge Control Value Charge control wattage sent from battery smart unit to power management control ECU/ Min.: -64.0 kW, Max.: 63.5 kW -33.0 kW or more -
Discharge Control Value Discharge control wattage sent from battery smart unit to power management control ECU/ Min.: -64.0 kW, Max.: 63.5 kW 30.0 kW or less -
Cooling Fan Mode1 Battery cooling blower assembly operation mode/ Min.: 0, Max.: 6 Power switch on (IG) or on (READY), and battery cooling blower assembly stopped:
0
Power switch on (IG) or on (READY), and battery cooling blower assembly low speed to high speed:
Battery cooling fan circuit
Cooling Fan Frequency1 Battery cooling blower assembly frequency Min.: 0.0 Hz, Max.: 6553.5 Hz - Battery cooling fan circuit
ECU Control Mode HV battery control mode/ Min.: 0, Max.: 4 Driving control mode:
0
Current sensor offset mode:
1
External charge control mode:
2
Power supply end mode:
3
-
Standby Blower Request Battery cooling blower assembly Lo speed requested/ ON or OFF Constant:
ON or OFF
Air conditioning system
Temp of Batt TB1 Battery module temperature/ Min.: -50.0°C (-58°F), Max.: 205.9°C (402.6°F) Undisturbed for 1 day:
Same as ambient air temperature
·

Battery temperature sensor

·

Battery smart unit


Temp of Batt TB2 Battery module temperature/ Min.: -50.0°C (-58°F), Max.: 205.9°C (402.6°F) Undisturbed for 1 day:
Same as ambient air temperature
·

Battery temperature sensor

·

Battery smart unit


Temp of Batt TB3 Battery module temperature/ Min.: -50.0°C (-58°F), Max.: 205.9°C (402.6°F) Undisturbed for 1 day:
Same as ambient air temperature
·

Battery temperature sensor

·

Battery smart unit


Battery Block Num The number of battery blocks - Always: 17 HV battery
Batt Block Minimum Vol Battery block minimum voltage/ Min.: 0.00 V, Max.: 79.99 V SOC 55.0 to 60.0%:
12.00 V or more
-
Minimum Batt Block No Battery block number with minimum voltage/ Min.: 0, Max.: 17 Any of block number 0 to 17 -
Batt Block Max Vol Battery block maximum voltage/ Min.: 0.00 V, Max.: 79.99 V SOC 55.0 to 60.0%:
23.00 V or less
-
Max Battery Block No Battery block number with maximum voltage/ Min.: 0, Max.: 17 Any of block number 0 to 17 -
Battery Block Vol -V01 Battery block voltage/ Min.: 0.00 V, Max.: 79.99 V SOC 60% :
12.00 to 20.00 V
·

HV battery

·

Battery smart unit


Battery Block Vol -V02 Battery block voltage/ Min.: 0.00 V, Max.: 79.99 V SOC 60% :
12.00 to 20.00 V
·

HV battery

·

Battery smart unit


Battery Block Vol -V03 Battery block voltage/ Min.: 0.00 V, Max.: 79.99 V SOC 60% :
12.00 to 20.00 V
·

HV battery

·

Battery smart unit


Battery Block Vol -V04 Battery block voltage/ Min.: 0.00 V, Max.: 79.99 V SOC 60% :
12.00 to 20.00 V
·

HV battery

·

Battery smart unit


Battery Block Vol -V05 Battery block voltage/ Min.: 0.00 V, Max.: 79.99 V SOC 60% :
12.00 to 20.00 V
·

HV battery

·

Battery smart unit


Battery Block Vol -V06 Battery block voltage/ Min.: 0.00 V, Max.: 79.99 V SOC 60% :
12.00 to 20.00 V
·

HV battery

·

Battery smart unit


Battery Block Vol -V07 Battery block voltage/ Min.: 0.00 V, Max.: 79.99 V SOC 60% :
12.00 to 20.00 V
·

HV battery

·

Battery smart unit


Battery Block Vol -V08 Battery block voltage/ Min.: 0.00 V, Max.: 79.99 V SOC 60% :
12.00 to 20.00 V
·

HV battery

·

Battery smart unit


Battery Block Vol -V09 Battery block voltage/ Min.: 0.00 V, Max.: 79.99 V SOC 60% :
12.00 to 20.00 V
·

HV battery

·

Battery smart unit


Battery Block Vol -V10 Battery block voltage/ Min.: 0.00 V, Max.: 79.99 V SOC 60% :
12.00 to 20.00 V
·

HV battery

·

Battery smart unit


Battery Block Vol -V11 Battery block voltage/ Min.: 0.00 V, Max.: 79.99 V SOC 60% :
12.00 to 20.00 V
·

HV battery

·

Battery smart unit


Battery Block Vol -V12 Battery block voltage/ Min.: 0.00 V, Max.: 79.99 V SOC 60% :
12.00 to 20.00 V
·

HV battery

·

Battery smart unit


Battery Block Vol -V13 Battery block voltage/ Min.: 0.00 V, Max.: 79.99 V SOC 60% :
12.00 to 20.00 V
·

HV battery

·

Battery smart unit


Battery Block Vol -V14 Battery block voltage/ Min.: 0.00 V, Max.: 79.99 V SOC 60% :
12.00 to 20.00 V
·

HV battery

·

Battery smart unit


Battery Block Vol -V15 Battery block voltage/ Min.: 0.00 V, Max.: 79.99 V SOC 60% :
12.00 to 20.00 V
·

HV battery

·

Battery smart unit


Battery Block Vol -V16 Battery block voltage/ Min.: 0.00 V, Max.: 79.99 V SOC 60% :
12.00 to 20.00 V
·

HV battery

·

Battery smart unit


Battery Block Vol -V17 Battery block voltage/ Min.: 0.00 V, Max.: 79.99 V SOC 60% :
12.00 to 20.00 V
·

HV battery

·

Battery smart unit


Internal Resistance R01 Internal resistance of each battery block/ Min.: 0.000 Ω, Max.: 0.255 Ω Always:
0.010 to 0.100 Ω
HV battery
Internal Resistance R02 Internal resistance of each battery block/ Min.: 0.000 Ω, Max.: 0.255 Ω Always:
0.010 to 0.100 Ω
HV battery
Internal Resistance R03 Internal resistance of each battery block/ Min.: 0.000 Ω, Max.: 0.255 Ω Always:
0.010 to 0.100 Ω
HV battery
Internal Resistance R04 Internal resistance of each battery block/ Min.: 0.000 Ω, Max.: 0.255 Ω Always:
0.010 to 0.100 Ω
HV battery
Internal Resistance R05 Internal resistance of each battery block/ Min.: 0.000 Ω, Max.: 0.255 Ω Always:
0.010 to 0.100 Ω
HV battery
Internal Resistance R06 Internal resistance of each battery block/ Min.: 0.000 Ω, Max.: 0.255 Ω Always:
0.010 to 0.100 Ω
HV battery
Internal Resistance R07 Internal resistance of each battery block/ Min.: 0.000 Ω, Max.: 0.255 Ω Always:
0.010 to 0.100 Ω
HV battery
Internal Resistance R08 Internal resistance of each battery block/ Min.: 0.000 Ω, Max.: 0.255 Ω Always:
0.010 to 0.100 Ω
HV battery
Internal Resistance R09 Internal resistance of each battery block/ Min.: 0.000 Ω, Max.: 0.255 Ω Always:
0.010 to 0.100 Ω
HV battery
Internal Resistance R10 Internal resistance of each battery block/ Min.: 0.000 Ω, Max.: 0.255 Ω Always:
0.010 to 0.100 Ω
HV battery
Internal Resistance R11 Internal resistance of each battery block/ Min.: 0.000 Ω, Max.: 0.255 Ω Always:
0.010 to 0.100 Ω
HV battery
Internal Resistance R12 Internal resistance of each battery block/ Min.: 0.000 Ω, Max.: 0.255 Ω Always:
0.010 to 0.100 Ω
HV battery
Internal Resistance R13 Internal resistance of each battery block/ Min.: 0.000 Ω, Max.: 0.255 Ω Always:
0.010 to 0.100 Ω
HV battery
Internal Resistance R14 Internal resistance of each battery block/ Min.: 0.000 Ω, Max.: 0.255 Ω Always:
0.010 to 0.100 Ω
HV battery
Internal Resistance R15 Internal resistance of each battery block/ Min.: 0.000 Ω, Max.: 0.255 Ω Always:
0.010 to 0.100 Ω
HV battery
Internal Resistance R16 Internal resistance of each battery block/ Min.: 0.000 Ω, Max.: 0.255 Ω Always:
0.010 to 0.100 Ω
HV battery
Internal Resistance R17 Internal resistance of each battery block/ Min.: 0.000 Ω, Max.: 0.255 Ω Always:
0.010 to 0.100 Ω
HV battery
Battery Low Time Cumulative total of extremely low HV battery charge level (engine not startable)/ Min.: 0, Max.: 65535 - -
DC Inhibit Time Cumulative total of extremely low HV battery charge level (engine startable)/ Min.: 0, Max.: 65535 - -
Battery too High Time Cumulative total of charging during charge prohibition state/ Min.: 0, Max.: 65535 - -
Hot Temperature Time Cumulative total of rapid HV battery temperature increase/ Min.: 0, Max.: 65535 - -


ACTIVE TEST


Using the intelligent tester to perform Active Tests allows relays, VSVs, actuators and other items to be operated without removing any parts. This non-intrusive functional inspection can be very useful because intermittent operation may be discovered before parts or wiring is disturbed. Performing Active Tests early in troubleshooting is one way to save diagnostic time. Data list information can be displayed while performing Active Tests.

NOTICE:

It is necessary to use caution, because if the tester DLC connector becomes disconnected or if a communication error occurs during an Active Test, the vehicle could become inoperative (the READY indicator may go off).


a.

Connect the intelligent tester to the DLC3.


b.

Turn the power switch on (IG).


c.

Turn the intelligent tester on.


d.

Enter the following menus: Powertrain / Hybrid Control / Active Test.


e.

According to the display on the intelligent tester perform the appropriate Active Test.

Powertrain > Hybrid Control > Active Test
Tester Display Measurement Item Control Range Diagnostic Note
Inspection Mode -2WD Inspection - -
NOTICE:

Enter inspection mode


Inspection Mode -2WD Chassis-Dynamo - -
NOTICE:

Enter inspection mode


Battery Charge To charge the HV battery using the THS charger -
·

Test Details

Allows current to flow into the HV battery by operating the SMRS


·

Test Condition

Power switch on (IG), shift lever in P, and other Active Tests not being performed



NOTICE:

The intelligent tester will display a communication error and the vehicle's READY indicator will turn off when the Active Test is completed. If the intelligent tester will be used on the vehicle again, turn the power switch off and then on (READY) again to restart the intelligent tester.


Compression Test To crank the engine continuously in order to measure the compression ON / OFF
·

Test Details

Allows the engine to continue cranking by activating MG1 continuously


·

Test Condition

Power switch on (IG), HV system normal, not in cranking mode, and other Active Tests not being done



NOTICE:

The intelligent tester will display a communication error and the vehicle's READY indicator will turn off when the Active Test is completed. If the intelligent tester will be used on the vehicle again, turn the power switch off and then on (READY) again to restart the intelligent tester.


Activate the Water Pump To activate the inverter water pump assembly continuously ON / OFF
·

Test Details

Activates the inverter water pump assembly continuously


·

Test Condition

Power switch on (IG), HV system normal, not in inspection mode, and auxiliary battery voltage is less than 9.5 V



Driving the Battery Cooling Fan To check operation of the cooling fan, and check if there is sufficient air flow 1 to 6
·

Test Details

Stops the cooling fan or changes air volume mode



Connect the TC and TE1 Batch display of warnings on combination meter ON / OFF
·

Test Details

TC terminal can be switched ON/OFF


·

Test Condition

Power switch on (IG), system is normal