Home › Engine / Hybrid System › HYBRID / BATTERY CONTROL › HYBRID CONTROL SYSTEM
RM2040EQ _51 Engine / Hybrid System _014692 HYBRID / BATTERY CONTROL _0074885 HYBRID CONTROL SYSTEM C

HYBRID / BATTERY CONTROL  HYBRID CONTROL SYSTEM  P0A0F-238  Engine Failed to Start  


DESCRIPTION

If the power management control ECU detects that the engine or transaxle gear has seized, the power management control ECU will perform fail-safe control. Also, if a substance or object is preventing the engine or transaxle internal components from rotating, the power management control ECU will perform fail-safe control.

A217594E09
4.521,1.719 5.188,1.135 true 2.594,1.74 1.875,1.125 true 4.917,4.427 5.5,4.25 true 4.938,5.052 5.958,4.813 true 4.875,5.594 6.01,5.24 true 2.156,4.417 2.729,4.563 true 1.677,4.833 2.688,5.26 true 1.635,5.26 2.646,5.688 true 2.417,0.833 4.698,1.156 2.281,0.323 10 false Hybrid Vehicle Transaxle Assembly 5.177,1.708 5.74,1.969 0.563,0.26 10 false Engine 5.24,1.031 5.615,1.313 0.375,0.281 10 false MG1 1.552,1.042 1.927,1.323 0.375,0.281 10 false MG2 4.271,4.344 4.938,4.615 0.667,0.271 10 false Ring Gear 2.771,4.49 3.438,4.76 0.667,0.271 10 false Ring Gear 3.906,4.969 5,5.24 1.094,0.271 10 false Sun Gear (MG1) 2.74,5.177 3.833,5.448 1.094,0.271 10 false Sun Gear (MG2) 4.125,5.51 4.958,5.781 0.833,0.271 10 false Pinion Gear 2.698,5.625 3.531,5.896 0.833,0.271 10 false Pinion Gear 0.25,5.927 3.073,6.302 2.823,0.375 10 false Motor Speed Reduction Planetary Gear Unit 5.01,5.927 7.042,6.302 2.031,0.375 10 false Power Split Planetary Gear Unit

DTC No. Detection Item DTC Detection Condition Trouble Area MIL Warning Indicate
P0A0F-238 Engine Failed to Start Engine does not start even though it is being cranked (transaxle input malfunction [engine system])
·

Hybrid vehicle transaxle assembly

·

Transmission input damper assembly

·

Power management control ECU

·

Engine


Does not come on Master Warning Light:
Comes on

CAUTION / NOTICE / HINT

HINT:

If this DTC is output, the engine or transaxle gear may be seized. Be sure to check the level of the engine oil, automatic transmission fluid (ATF) and coolant before inspection.


PROCEDURE

1.CHECK DTC OUTPUT (HYBRID CONTROL)
a.

Connect the intelligent tester to the DLC3.


b.

Turn the power switch on (IG).


c.

Enter the following menus: Powertrain / Hybrid Control / DTC.

Powertrain > Hybrid Control > Trouble Codes
50001 236

d.

Check if DTCs are output.

Result:
Result Proceed to
P0A0F-238 only is output. A
P0A1D (Hybrid Powertrain Control Module) is output. B



e.

Turn the power switch off.



A

2.CHECK CRANKSHAFT PULLEY REVOLUTION (P POSITION)

B

2.CHECK CRANKSHAFT PULLEY REVOLUTION (P POSITION)
a.

Check that the shift lever is in the P position.


b.

Lift up the vehicle.


c.

Turn the crankshaft pulley using hand tools to check if the crankshaft can rotate smoothly.

CAUTION:

Do not turn the power switch on (READY) while performing this inspection. Be sure to turn the power switch off before performing this inspection, to prevent the engine from starting.


NOTICE:

Engine compression causes resistance when turning the crankshaft pulley. Check if the crankshaft rotates smoothly (or if it is locked) by manually applying sufficient torque to turn the crankshaft pulley. The torque required to turn the crankshaft pulley should be the same as for a known good vehicle of the same type.


OK:

The crankshaft rotates smoothly.



d.

Lower the vehicle.

Result:
Proceed to
OK
NG




OK

3.CLEAR DTC

NG

7.CHECK CRANKSHAFT PULLEY REVOLUTION (N POSITION)
3.CLEAR DTC
a.

Connect the intelligent tester to the DLC3.


b.

Turn the power switch on (IG).


c.

Enter the following menus: Powertrain / Hybrid Control / DTC.

Powertrain > Hybrid Control > Trouble Codes
50001 236

d.

Read and record the DTCs and freeze frame data.


e.

Clear DTCs and freeze frame data.

Powertrain > Hybrid Control > Clear DTCs
50002 236

f.

Turn the power switch off.

Result:
Proceed to
NEXT




NEXT

4.CHECK ENGINE RACING
4.CHECK ENGINE RACING
a.

Connect the intelligent tester to the DLC3.


b.

Turn the power switch on (READY).


c.

Enter the following menus: Powertrain / Hybrid Control / Data List / Generator (MG1) Rev, Engine Revolution.

Powertrain > Hybrid Control > Data List
Tester Display
Engine Revolution
Generator(MG1) Rev
50003 236 9,569

d.

Read the Data List.


e.
A212091E06
2.094,1.948 2.365,1.458 false 0.938,1.448 1.146,1.198 1.146,1.198 1.063,1.729 false 2.198,1.156 2.708,1.344 0.51,0.188 10 Normal 0.813,0.875 1.615,1.031 0.802,0.156 10 Malfunction 1.583,2.458 2.094,2.646 0.51,0.188 10 Engine 2.771,2.458 3.135,2.646 0.365,0.188 10 MG2 0.51,2.458 0.875,2.646 0.365,0.188 10 MG1

While the READY indicator is on, fully depress the accelerator pedal for 10 seconds.

OK:

Generator (MG1) Rev increases to approximately 3.6 times that of Engine Revolution.


HINT:

Refer to the graph for Data List confirmation of "Generator (MG1) Rev" and " Engine Revolution".

Data List ENGINE REV MG1 REV
Reference Value Approximately 1000 rpm Approximately 3600 rpm
Approximately 1500 rpm Approximately 5400 rpm
Approximately 2500 rpm Approximately 9000 rpm



f.

Turn the power switch off.

Result:
Proceed to
OK
NG




OK

5.CHECK CREEP MOVEMENT

NG

REPLACE HYBRID VEHICLE TRANSAXLE ASSEMBLY

5.CHECK CREEP MOVEMENT
a.

Turn the power switch on (READY).


b.

Depress the brake pedal, move the shift lever to D, and release the brake pedal.

OK:

The wheels turn (the vehicle creeps forward).



c.

Turn the power switch off.

Result:
Proceed to
OK
NG




OK

6.INSPECT ENGINE SPEED

NG

REPLACE HYBRID VEHICLE TRANSAXLE ASSEMBLY

6.INSPECT ENGINE SPEED
a.

Connect the intelligent tester to the DLC3.


b.

Turn the power switch on (READY).


c.

Enter the following menus: Powertrain / Hybrid Control / Data List / Motor (MG2) Revolution, Generator (MG1) Rev, Engine Revolution.

Powertrain > Hybrid Control > Data List
Tester Display
Engine Revolution
Motor(MG2) Revolution
Generator(MG1) Rev
50003 236 9,573,569

d.

Read the Data List.


e.

Move the shift lever to D.


f.

Fully depress the accelerator pedal to accelerate the vehicle from a stop.

NOTICE:

Perform this test only in an appropriate safe location, in accordance with all local laws.


OK:

The difference between Engine Revolution and 0.28 X Generator (MG1) Rev + 0.29 X Motor (MG2) Revolution is 500 rpm or more and it is maintained for 1 second.



g.

Turn the power switch off.

Result:
Proceed to
OK
NG




OK

NG

REPLACE TRANSMISSION INPUT DAMPER ASSEMBLY

7.CHECK CRANKSHAFT PULLEY REVOLUTION (N POSITION)
a.

Lift up the vehicle.


b.

Move the shift lever to N.


c.

Turn the crankshaft pulley using hand tools to check if the crankshaft can rotate smoothly.

CAUTION:

Do not turn the power switch on (READY) while performing this inspection. Be sure to turn the power switch off before performing this inspection, to prevent the engine from starting.


NOTICE:

Engine compression causes resistance when turning the crankshaft pulley. Check if the crankshaft rotates smoothly (or if it is locked) by manually applying sufficient torque to turn the crankshaft pulley. The torque required to turn the crankshaft pulley should be the same as for a known good vehicle of the same type.


OK:

The crankshaft rotates smoothly.



d.

Lower the vehicle.

Result:
Proceed to
OK
NG




OK

REPLACE HYBRID VEHICLE TRANSAXLE ASSEMBLY

NG

REPAIR OR REPLACE ENGINE