Home › Engine / Hybrid System › HYBRID / BATTERY CONTROL › HYBRID CONTROL SYSTEM
RM2040EQ _51 Engine / Hybrid System _014692 HYBRID / BATTERY CONTROL _0074885 HYBRID CONTROL SYSTEM C

HYBRID / BATTERY CONTROL  HYBRID CONTROL SYSTEM  P2532-772  Ignition Switch Run Position Circuit High  


DESCRIPTION

The power source and HV CPU processors and their functions are integrated into the power management control ECU. The power source CPU and HV CPU use CAN communication to communicate with each other inside the power management control ECU. The power source CPU controls the opening and closing of the IG2 relay. The HV CPU detects that the IG2 relay is stuck ON (closed) based on relay operation information received from the power source CPU via CAN communication.

DTC No. Detection Item DTC Detection Condition Trouble Area MIL Warning Indicate
P2532-772 Ignition Switch Run Position Circuit High Voltage is still applied to IG2 terminal although an IG2 relay off command is received from the power source CPU.
·

Wire harness or connector

·

No. 1 integration relay (IG2 relay)

·

Power management control ECU


Does not come on Master Warning Light:
Comes on

HINT:

If DTC P2532-772 is stored, the vehicle will turn off.


WIRING DIAGRAM

A259915
4.844,1.979 5.646,2.156 0.802,0.177 10 false A39 4.792,2.229 6.938,2.542 2.146,0.313 10 false Power Management Control ECU 5.417,0.917 5.927,1.094 0.51,0.177 10 false IG2 3.802,0.906 4.021,1.083 0.219,0.177 10 false 1C 3.833,0.719 4.052,0.896 0.219,0.177 10 false 5 3.833,1.125 4.052,1.302 0.219,0.177 10 false 8 3.813,1.354 4.031,1.531 0.219,0.177 10 false 1C 1.5,0.917 1.844,1.177 0.344,0.26 10 false 1D 1.552,0.708 1.771,0.885 0.219,0.177 10 false 3 1.531,1.135 1.781,1.344 0.25,0.208 10 false 2 1.469,1.344 1.76,1.552 0.292,0.208 10 false 1E 5.427,1.344 5.938,1.521 0.51,0.177 10 false IG2D 5.229,0.719 5.385,0.896 0.156,0.177 10 false 1 5.219,1.208 5.375,1.385 0.156,0.177 10 false 2 2.625,1.771 2.917,1.948 0.292,0.177 10 false IG2 0.531,1.094 1.344,1.333 0.813,0.24 10 false IG2-MAIN 1.979,2.198 3.885,2.49 1.906,0.292 10 false No. 1 Integration Relay 4.177,1.104 5.219,1.281 1.042,0.177 10 false ECU-IG2 NO. 1

PROCEDURE

1.CHECK HARNESS AND CONNECTOR (+B SHORT)
a.

Disconnect connector A39 from the power management control ECU.


b.
A250971
1.271,2.875 1.688,3.115 0.417,0.24 1.656,2.25 2.01,2.042 true 1.604,2.25 2.021,2.427 true 1.333,2.917 1.844,3.208 0.51,0.292 10 false A39 2.031,1.958 2.354,2.125 0.323,0.167 10 false IG2 2.083,2.354 2.469,2.531 0.385,0.177 10 false IG2D 0.042,0.063 0.323,0.333 0.281,0.271 10 false *a
*a Rear view of wire harness connector
(to Power Management Control ECU)


Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition
A39-1 (IG2) - Body ground Power switch off Below 1 V
A39-2 (IG2D) - Body ground Power switch off Below 1 V


Result:
Result Proceed to
NG A
OK B



c.

Connect the power management control ECU connector.



A

2.CHECK HARNESS AND CONNECTOR (POWER MANAGEMENT CONTROL ECU - NO. 1 INTEGRATION RELAY)

B

2.CHECK HARNESS AND CONNECTOR (POWER MANAGEMENT CONTROL ECU - NO. 1 INTEGRATION RELAY)
a.

Disconnect connector A39 from the power management control ECU.


b.

Remove the No. 1 integration relay from the engine room relay block and junction block assembly.


c.
A250971
1.271,2.865 1.688,3.104 0.417,0.24 1.656,2.25 1.99,2.042 true 1.583,2.25 2.021,2.427 true 1.333,2.885 1.885,3.156 0.552,0.271 10 false A39 2.042,1.958 2.365,2.125 0.323,0.167 10 false IG2 2.031,2.365 2.417,2.542 0.385,0.177 10 false IG2D 0.042,0.042 0.198,0.208 0.156,0.167 10 false *a
*a Rear view of wire harness connector
(to Power Management Control ECU)


Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition
A39-1 (IG2) - Body ground Power switch off Below 1 V
A39-2 (IG2D) - Body ground Power switch off Below 1 V



d.

Install the No. 1 integration relay.


e.

Connect the power management control ECU connector.

Result:
Proceed to
OK
NG




OK

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR