Home › Engine / Hybrid System › HYBRID / BATTERY CONTROL › HYBRID CONTROL SYSTEM › 2012.02–2016.05
RM2040EQ _51 Engine / Hybrid System _014692 HYBRID / BATTERY CONTROL _0074885 HYBRID CONTROL SYSTEM C

HYBRID / BATTERY CONTROL  HYBRID CONTROL SYSTEM  P0A1A-200  Generator Control Module  P0A1A-792  Generator Control Module  P0A1A-793  Generator Control Module  


DESCRIPTION

The MG ECU located in the inverter with converter assembly monitors its internal operation and detects the following malfunctions.

DTC No. Detection Item DTC Detection Condition Trouble Area MIL Warning Indicate
P0A1A-200 Generator Control Module The difference between the resolver angle for control and estimated resolver angle exceeds the allowable value.
·

Inverter with converter assembly

·

Hybrid vehicle transaxle assembly

·

Wire harness or connector


Comes on Master Warning Light:
Comes on
P0A1A-792 Generator Control Module Resolver REF signal cycle error
·

Inverter with converter assembly

·

Hybrid vehicle transaxle assembly

·

Wire harness or connector


Comes on Master Warning Light:
Comes on
P0A1A-793 Generator Control Module Resolver REF signal oscillation stop error
·

Inverter with converter assembly

·

Hybrid vehicle transaxle assembly

·

Wire harness or connector


Comes on Master Warning Light:
Comes on

WIRING DIAGRAM

A220049E15
1.854,3.042 1.99,3.229 0.135,0.188 10 false 1 1.865,3.698 2,3.885 0.135,0.188 10 false 2 1.865,4.354 2,4.542 0.135,0.188 10 false 3 1.865,1.333 2,1.521 0.135,0.188 10 false 2 1.865,1.656 2,1.844 0.135,0.188 10 false 5 1.865,1.99 2,2.177 0.135,0.188 10 false 3 1.865,2.313 2,2.5 0.135,0.188 10 false 6 1.854,0.677 1.99,0.865 0.135,0.188 10 false 1 1.865,1.01 2,1.198 0.135,0.188 10 false 4 0.25,5.396 2.521,5.594 2.271,0.198 10 false Hybrid Vehicle Transaxle Assembly 0.719,5.073 2.01,5.271 1.292,0.198 10 false Generator Resolver 0.719,2.688 1.75,2.885 1.031,0.198 10 false Motor Resolver 1.49,4.354 1.885,4.542 0.396,0.188 10 false GCS 1.5,3.698 1.875,3.885 0.375,0.188 10 false GSN 1.5,3.052 1.865,3.24 0.365,0.188 10 false GRF 1.385,4.688 1.823,4.875 0.438,0.188 10 false GCSG 1.385,4.021 1.833,4.208 0.448,0.188 10 false GSNG 1.396,3.375 1.854,3.563 0.458,0.188 10 false GRFG 1.479,1.99 1.875,2.177 0.396,0.188 10 false MCS 1.49,1.333 1.865,1.521 0.375,0.188 10 false MSN 1.49,0.688 1.854,0.875 0.365,0.188 10 false MRF 1.375,2.323 1.813,2.51 0.438,0.188 10 false MCSG 1.375,1.656 1.823,1.844 0.448,0.188 10 false MSNG 1.385,1.01 1.844,1.198 0.458,0.188 10 false MRFG 4.365,5.167 4.656,5.323 0.292,0.156 10 false E1 4.354,5.354 7.125,5.563 2.771,0.208 10 false Inverter with Converter Assembly (MG ECU) 5.281,4.448 5.677,4.635 0.396,0.188 10 false GCS 5.281,3.802 5.656,3.99 0.375,0.188 10 false GSN 5.281,3.135 5.646,3.323 0.365,0.188 10 false GRF 5.281,4.75 5.719,4.938 0.438,0.188 10 false GCSG 5.281,4.125 5.729,4.313 0.448,0.188 10 false GSNG 5.281,3.479 5.74,3.667 0.458,0.188 10 false GRFG 5.281,2.073 5.677,2.26 0.396,0.188 10 false MCS 5.281,1.427 5.656,1.615 0.375,0.188 10 false MSN 5.281,0.771 5.646,0.958 0.365,0.188 10 false MRF 5.281,2.406 5.719,2.594 0.438,0.188 10 false MCSG 5.281,1.75 5.729,1.938 0.448,0.188 10 false MSNG 5.281,1.094 5.74,1.281 0.458,0.188 10 false MRFG 5.281,2.75 5.719,2.938 0.438,0.188 10 false DRN6 5.073,3.042 5.198,3.229 0.125,0.188 10 false 1 5.073,3.698 5.208,3.885 0.135,0.188 10 false 2 5.073,4.021 5.208,4.208 0.135,0.188 10 false 8 5.073,4.677 5.208,4.865 0.135,0.188 10 false 9 0.719,2.521 1,2.708 0.281,0.188 10 false E12 0.719,4.906 0.99,5.094 0.271,0.188 10 false E13 1.865,3.375 2,3.563 0.135,0.188 10 false 5 1.865,4.021 2,4.208 0.135,0.188 10 false 6 1.865,4.688 2,4.875 0.135,0.188 10 false 7 5.073,0.667 5.208,0.854 0.135,0.188 10 false 4 5.021,0.99 5.198,1.177 0.177,0.188 10 false 11 5.083,1.302 5.219,1.49 0.135,0.188 10 false 5 5.021,1.656 5.219,1.844 0.198,0.188 10 false 12 5.031,2.292 5.219,2.479 0.188,0.188 10 false 13 5.063,1.969 5.198,2.156 0.135,0.188 10 false 6 5.073,3.365 5.188,3.552 0.115,0.188 10 false 7 5.073,4.354 5.271,4.542 0.198,0.188 10 false 3 5.031,2.646 5.229,2.833 0.198,0.188 10 false 10

CAUTION / NOTICE / HINT

CAUTION:
·

Before inspecting the high-voltage system or disconnecting the low voltage connector of the inverter with converter assembly, take safety precautions such as wearing insulated gloves and removing the service plug grip to prevent electrical shocks. After removing the service plug grip, put it in your pocket to prevent other technicians from accidentally reconnecting it while you are working on the high-voltage system.

·

After removing the service plug grip, wait for at least 10 minutes before touching any of the high-voltage connectors or terminals. After waiting for 10 minutes, check the voltage at the terminals in the inspection point in the inverter with converter assembly. The voltage should be 0 V before beginning work (See page Engine / Hybrid System>HYBRID / BATTERY CONTROL>HYBRID CONTROL SYSTEM>PRECAUTION).

HINT:

Waiting for at least 10 minutes is required to discharge the high-voltage capacitor inside the inverter with converter assembly.




NOTICE:

After turning the power switch off, waiting time may be required before disconnecting the cable from the negative (-) auxiliary battery terminal. Therefore, make sure to read the disconnecting the cable from the negative (-) auxiliary battery terminal notices before proceeding with work (See page General>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION).


PROCEDURE

1.CHECK DTC OUTPUT (HYBRID CONTROL)
a.

Connect the intelligent tester to the DLC3.


b.

Turn the power switch on (IG).


c.

Enter the following menus: Powertrain / Hybrid Control / DTC.

Powertrain > Hybrid Control > Trouble Codes
50001 236

d.

Check if DTCs are output.

Result:
Result Proceed to
P0A1A-200, 792 or 793 only is output. A
Any of the following DTCs are also output. B


DTC No. Relevant Diagnosis
P0A3F-243 Drive Motor "A" Position Sensor Circuit
P0A4B-253 Generator Position Sensor Circuit
P0A4C-513 Generator Position Sensor Circuit Range / Performance
P0A4D-255 Generator Position Sensor Circuit Low


e.

Turn the power switch off.



A

2.CHECK CONNECTOR CONNECTION CONDITION (INVERTER WITH CONVERTER ASSEMBLY CONNECTOR)

B

2.CHECK CONNECTOR CONNECTION CONDITION (INVERTER WITH CONVERTER ASSEMBLY CONNECTOR)

OK

3.CHECK HARNESS AND CONNECTOR (INVERTER WITH CONVERTER ASSEMBLY - GENERATOR RESOLVER)

NG

CONNECT SECURELY

3.CHECK HARNESS AND CONNECTOR (INVERTER WITH CONVERTER ASSEMBLY - GENERATOR RESOLVER)
CAUTION:

Be sure to wear insulated gloves.


a.

Check that the service plug grip is not installed.

NOTICE:

After removing the service plug grip, do not turn the power switch on (READY), unless instructed by the repair manual because this may cause a malfunction.



b.

Disconnect connector E1 from the inverter with converter assembly.


c.

Connect the cable to the negative (-) auxiliary battery terminal.


d.

Turn the power switch on (IG).


e.
A259709C05
0.219,1.073 0.677,1.354 0.458,0.281 1.188,1.063 0.896,0.615 false 0.875,1.76 1.167,1.313 false 1.365,1.052 1.365,0.448 false 1.365,1.854 1.365,1.333 false 1.552,1.063 1.938,0.49 false 1.948,1.792 1.563,1.313 false 0.365,1.125 0.563,1.292 0.198,0.167 10 false E1 0.594,0.5 0.958,0.677 0.365,0.177 10 false GRF 1.208,0.271 1.583,0.438 0.375,0.167 10 false GSN 1.802,0.323 2.167,0.531 0.365,0.208 10 false GCS 0.604,1.781 1.031,1.948 0.427,0.167 10 false GRFG 1.146,1.875 1.573,2.042 0.427,0.167 10 false GSNG 1.792,1.813 2.219,1.979 0.427,0.167 10 false GCSG 0.083,0.052 0.26,0.219 0.177,0.167 10 false *a
*a Front view of wire harness connector
(to Inverter with Converter Assembly)


Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition
E1-1 (GRF) - Body ground Power switch on (IG) Below 1 V
E1-7 (GRFG) - Body ground Power switch on (IG) Below 1 V
E1-2 (GSN) - Body ground Power switch on (IG) Below 1 V
E1-8 (GSNG) - Body ground Power switch on (IG) Below 1 V
E1-3 (GCS) - Body ground Power switch on (IG) Below 1 V
E1-9 (GCSG) - Body ground Power switch on (IG) Below 1 V


NOTICE:

Turning the power switch on (IG) with the low voltage connector of the inverter with converter assembly disconnected causes other DTCs to be stored. Clear the DTCs after performing this inspection.



f.

Turn the power switch off.


g.

Disconnect the cable from the negative (-) auxiliary battery terminal.


h.

Connect the inverter with converter assembly connector.

Result:
Proceed to
OK
NG




OK

4.CHECK GENERATOR RESOLVER

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

4.CHECK GENERATOR RESOLVER
CAUTION:

Be sure to wear insulated gloves.


a.

Check that the service plug grip is not installed.

NOTICE:

After removing the service plug grip, do not turn the power switch on (READY), unless instructed by the repair manual because this may cause a malfunction.



b.

Disconnect connector E1 from the inverter with converter assembly.


c.
A259709C05
0.219,1.073 0.677,1.354 0.458,0.281 1.188,1.063 0.896,0.615 false 0.875,1.76 1.167,1.313 false 1.365,1.052 1.365,0.448 false 1.365,1.854 1.365,1.333 false 1.552,1.063 1.938,0.49 false 1.948,1.792 1.563,1.313 false 0.365,1.125 0.563,1.292 0.198,0.167 10 false E1 0.594,0.5 0.958,0.677 0.365,0.177 10 false GRF 1.208,0.271 1.583,0.438 0.375,0.167 10 false GSN 1.802,0.323 2.167,0.531 0.365,0.208 10 false GCS 0.604,1.781 1.031,1.948 0.427,0.167 10 false GRFG 1.146,1.875 1.573,2.042 0.427,0.167 10 false GSNG 1.792,1.813 2.219,1.979 0.427,0.167 10 false GCSG 0.083,0.052 0.26,0.219 0.177,0.167 10 false *a
*a Front view of wire harness connector
(to Inverter with Converter Assembly)


Measure the resistance according to the value(s) in the table below.

Standard Resistance (Check for Open):
Tester Connection Switch Condition Specified Condition
E1-1 (GRF) - E1-7 (GRFG) Power switch off 4.2 to 12.5 Ω
E1-2 (GSN) - E1-8 (GSNG) Power switch off 9.8 to 20.1 Ω
E1-3 (GCS) - E1-9 (GCSG) Power switch off 9.8 to 20.1 Ω


Standard Resistance (Check for Short):
Tester Connection Switch Condition Specified Condition
E1-1 (GRF) or E1-7 (GRFG) - Body ground and other terminals Power switch off 1 MΩ or higher
E1-2 (GSN) or E1-8 (GSNG) - Body ground and other terminals Power switch off 1 MΩ or higher
E1-3 (GCS) or E1-9 (GCSG) - Body ground and other terminals Power switch off 1 MΩ or higher



d.

Connect the inverter with converter assembly connector.

Result:
Proceed to
OK
NG




OK

5.CHECK HARNESS AND CONNECTOR (INVERTER WITH CONVERTER ASSEMBLY - MOTOR RESOLVER)

NG

9.CHECK CONNECTOR CONNECTION CONDITION (GENERATOR RESOLVER CONNECTOR)
5.CHECK HARNESS AND CONNECTOR (INVERTER WITH CONVERTER ASSEMBLY - MOTOR RESOLVER)
CAUTION:

Be sure to wear insulated gloves.


a.

Check that the service plug grip is not installed.

NOTICE:

After removing the service plug grip, do not turn the power switch on (READY), unless instructed by the repair manual because this may cause a malfunction.



b.

Disconnect connector E1 from the inverter with converter assembly.


c.

Connect the cable to the negative (-) auxiliary battery terminal.


d.

Turn the power switch on (IG).


e.
A259709C06
0.229,1.073 0.688,1.354 0.458,0.281 1.792,1.073 1.427,0.5 false 1.51,1.771 1.813,1.323 false 1.969,1.042 1.969,0.438 false 1.969,1.854 1.969,1.323 false 2.177,1.063 2.563,0.49 false 2.563,1.802 2.177,1.323 false 0.375,1.125 0.563,1.292 0.188,0.167 10 false E1 1.24,0.333 1.563,0.479 0.323,0.146 10 false MRF 1.813,0.271 2.146,0.438 0.333,0.167 10 false MSN 2.427,0.323 2.76,0.49 0.333,0.167 10 false MCS 1.115,1.771 1.542,1.938 0.427,0.167 10 false MRFG 1.74,1.885 2.188,2.052 0.448,0.167 10 false MSNG 2.375,1.823 2.823,1.99 0.448,0.167 10 false MCSG 0.083,0.052 0.26,0.219 0.177,0.167 10 false *a
*a Front view of wire harness connector
(to Inverter with Converter Assembly)


Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition
E1-4 (MRF) - Body ground Power switch on (IG) Below 1 V
E1-11 (MRFG) - Body ground Power switch on (IG) Below 1 V
E1-5 (MSN) - Body ground Power switch on (IG) Below 1 V
E1-12 (MSNG) - Body ground Power switch on (IG) Below 1 V
E1-6 (MCS) - Body ground Power switch on (IG) Below 1 V
E1-13 (MCSG) - Body ground Power switch on (IG) Below 1 V


NOTICE:

Turning the power switch on (IG) with the low voltage connector of the inverter with converter assembly disconnected causes other DTCs to be stored. Clear the DTCs after performing this inspection.



f.

Turn the power switch off.


g.

Disconnect the cable from the negative (-) auxiliary battery terminal.


h.

Connect the inverter with converter assembly connector.

Result:
Proceed to
OK
NG




OK

6.CHECK MOTOR RESOLVER

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

6.CHECK MOTOR RESOLVER
CAUTION:

Be sure to wear insulated gloves.


a.

Check that the service plug grip is not installed.

NOTICE:

After removing the service plug grip, do not turn the power switch on (READY), unless instructed by the repair manual because this may cause a malfunction.



b.

Disconnect connector E1 from the inverter with converter assembly.


c.
A259709C06
0.229,1.073 0.688,1.354 0.458,0.281 1.792,1.073 1.427,0.5 false 1.51,1.771 1.813,1.323 false 1.969,1.042 1.969,0.438 false 1.969,1.854 1.969,1.323 false 2.177,1.063 2.563,0.49 false 2.563,1.802 2.177,1.323 false 0.375,1.125 0.563,1.292 0.188,0.167 10 false E1 1.24,0.333 1.563,0.479 0.323,0.146 10 false MRF 1.813,0.271 2.146,0.438 0.333,0.167 10 false MSN 2.427,0.323 2.76,0.49 0.333,0.167 10 false MCS 1.115,1.771 1.542,1.938 0.427,0.167 10 false MRFG 1.74,1.885 2.188,2.052 0.448,0.167 10 false MSNG 2.375,1.823 2.823,1.99 0.448,0.167 10 false MCSG 0.083,0.052 0.26,0.219 0.177,0.167 10 false *a
*a Front view of wire harness connector
(to Inverter with Converter Assembly)


Measure the resistance according to the value(s) in the table below.

Standard Resistance (Check for Open):
Tester Connection Switch Condition Specified Condition
E1-4 (MRF) - E1-11 (MRFG) Power switch off 4.2 to 12.5 Ω
E1-5 (MSN) - E1-12 (MSNG) Power switch off 9.8 to 20.1 Ω
E1-6 (MCS) - E1-13 (MCSG) Power switch off 9.8 to 20.1 Ω


Standard Resistance (Check for Short):
Tester Connection Switch Condition Specified Condition
E1-4 (MRF) or E1-11 (MRFG) - Body ground and other terminals Power switch off 1 MΩ or higher
E1-5 (MSN) or E1-12 (MSNG) - Body ground and other terminals Power switch off 1 MΩ or higher
E1-6 (MCS) or E1-13 (MCSG) - Body ground and other terminals Power switch off 1 MΩ or higher



d.

Connect the inverter with converter assembly connector.

Result:
Proceed to
OK
NG




OK

7.CHECK CONNECTOR CONNECTION CONDITION (GENERATOR RESOLVER CONNECTOR)

NG

11.CHECK CONNECTOR CONNECTION CONDITION (MOTOR RESOLVER CONNECTOR)
7.CHECK CONNECTOR CONNECTION CONDITION (GENERATOR RESOLVER CONNECTOR)
a.
A259190

Check the connection of the generator resolver connector.

OK:

The connector is connected securely and there are no contact problems.



Result:
Proceed to
OK
NG



OK

8.CHECK CONNECTOR CONNECTION CONDITION (MOTOR RESOLVER CONNECTOR)

NG

CONNECT SECURELY

8.CHECK CONNECTOR CONNECTION CONDITION (MOTOR RESOLVER CONNECTOR)
a.
A259189

Check the connection of the motor resolver connector.

OK:

The connector is connected securely and there are no contact problems.



Result:
Proceed to
OK
NG



OK

REPLACE INVERTER WITH CONVERTER ASSEMBLY

NG

CONNECT SECURELY

9.CHECK CONNECTOR CONNECTION CONDITION (GENERATOR RESOLVER CONNECTOR)
a.
A259190

Check the connection of the generator resolver connector.

OK:

The connector is connected securely and there are no contact problems.



Result:
Proceed to
OK
NG



OK

10.CHECK HARNESS AND CONNECTOR (INVERTER WITH CONVERTER ASSEMBLY - GENERATOR RESOLVER)

NG

CONNECT SECURELY

10.CHECK HARNESS AND CONNECTOR (INVERTER WITH CONVERTER ASSEMBLY - GENERATOR RESOLVER)
CAUTION:

Be sure to wear insulated gloves.


a.

Check that the service plug grip is not installed.

NOTICE:

After removing the service plug grip, do not turn the power switch on (READY), unless instructed by the repair manual because this may cause a malfunction.



b.

Disconnect connector E1 from the inverter with converter assembly.


c.

Disconnect the generator resolver connector.


d.

Measure the resistance according to the value(s) in the table below.

A283299C02
0.708,1.51 1.083,1.719 0.375,0.208 6.104,1.458 6.469,1.656 0.365,0.198 1.792,1.5 1.521,0.927 false 2.063,1.469 2.167,0.875 false 2.25,1.5 2.656,0.906 false 1.521,2.219 1.813,1.708 false 2.229,2.24 2.073,1.719 false 2.792,2.25 2.229,1.729 false 4.781,1.479 4.365,0.844 false 4.896,1.469 5,0.802 false 5.031,1.469 5.552,0.833 false 4.333,2.229 4.729,1.677 false 5.01,2.198 4.865,1.677 false 5.646,2.198 5.052,1.677 false 1.396,0.729 1.74,0.906 0.344,0.177 10 false GRF 2,0.698 2.385,0.917 0.385,0.219 10 false GSN 2.542,0.74 2.938,0.938 0.396,0.198 10 false GCS 1.344,2.281 1.813,2.479 0.469,0.198 10 false GRFG 2.042,2.292 2.5,2.448 0.458,0.156 10 false GSNG 2.667,2.302 3.177,2.469 0.51,0.167 10 false GCSG 4.208,0.667 4.573,0.813 0.365,0.146 10 false GRF 4.854,0.635 5.24,0.844 0.385,0.208 10 false GSN 5.438,0.667 5.823,0.854 0.385,0.188 10 false GCS 4.156,2.26 4.656,2.479 0.5,0.219 10 false GRFG 4.875,2.25 5.375,2.438 0.5,0.188 10 false GSNG 5.51,2.229 6.031,2.427 0.521,0.198 10 false GCSG 0.76,1.542 1.167,1.708 0.406,0.167 10 false E13 6.188,1.49 6.531,1.635 0.344,0.146 10 false E1 0.719,0.583 1.031,0.74 0.313,0.156 10 false *a 3.656,0.604 3.969,0.76 0.313,0.156 10 false *b
*a Front view of wire harness connector
(to Generator Resolver)
*b Front view of wire harness connector
(to Inverter with Converter Assembly)


Standard Resistance (Check for Open):
Tester Connection Switch Condition Specified Condition
E1-1 (GRF) - E13-1 (GRF) Power switch off Below 1 Ω
E1-7 (GRFG) - E13-5 (GRFG) Power switch off Below 1 Ω
E1-2 (GSN) - E13-2 (GSN) Power switch off Below 1 Ω
E1-8 (GSNG) - E13-6 (GSNG) Power switch off Below 1 Ω
E1-3 (GCS) - E13-3 (GCS) Power switch off Below 1 Ω
E1-9 (GCSG) - E13-7 (GCSG) Power switch off Below 1 Ω


Standard Resistance (Check for Short):
Tester Connection Switch Condition Specified Condition
E1-1 (GRF) or E13-1 (GRF) - Body ground and other terminals Power switch off 1 MΩ or higher
E1-7 (GRFG) or E13-5 (GRFG) - Body ground and other terminals Power switch off 1 MΩ or higher
E1-2 (GSN) or E13-2 (GSN) - Body ground and other terminals Power switch off 1 MΩ or higher
E1-8 (GSNG) or E13-6 (GSNG) - Body ground and other terminals Power switch off 1 MΩ or higher
E1-3 (GCS) or E13-3 (GCS) - Body ground and other terminals Power switch off 1 MΩ or higher
E1-9 (GCSG) or E13-7 (GCSG) - Body ground and other terminals Power switch off 1 MΩ or higher


HINT:

The generator resolver is not available separately. If it requires replacement, replace the hybrid vehicle transaxle assembly.



e.

Connect the generator resolver connector.


f.

Connect the inverter with converter assembly connector.

Result:
Proceed to
OK
NG




OK

REPLACE HYBRID VEHICLE TRANSAXLE ASSEMBLY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

11.CHECK CONNECTOR CONNECTION CONDITION (MOTOR RESOLVER CONNECTOR)
a.
A259189

Check the connection of the motor resolver connector.

OK:

The connector is connected securely and there are no contact problems.



Result:
Proceed to
OK
NG



OK

12.CHECK HARNESS AND CONNECTOR (INVERTER WITH CONVERTER ASSEMBLY - MOTOR RESOLVER)

NG

CONNECT SECURELY

12.CHECK HARNESS AND CONNECTOR (INVERTER WITH CONVERTER ASSEMBLY - MOTOR RESOLVER)
CAUTION:

Be sure to wear insulated gloves.


a.

Check that the service plug grip is not installed.

NOTICE:

After removing the service plug grip, do not turn the power switch on (READY), unless instructed by the repair manual because this may cause a malfunction.



b.

Disconnect connector E1 from the inverter with converter assembly.


c.

Disconnect the motor resolver connector.


d.

Measure the resistance according to the value(s) in the table below.

A283300C02
0.688,1.427 1.052,1.635 0.365,0.208 6.052,1.406 6.417,1.615 0.365,0.208 1.958,1.385 1.5,0.677 false 2.146,1.365 2.115,0.677 false 2.344,1.385 2.708,0.677 false 1.479,2.281 1.948,1.625 false 2.135,2.25 2.146,1.625 false 2.813,2.25 2.354,1.604 false 5.156,1.438 4.458,0.76 false 5.302,1.438 5.063,0.719 false 5.417,1.427 5.667,0.74 false 4.302,2.177 5.177,1.615 false 5.094,2.177 5.313,1.625 false 5.781,2.135 5.458,1.615 false 1.354,0.531 1.719,0.74 0.365,0.208 10 false MRF 1.948,0.5 2.385,0.719 0.438,0.219 10 false MSN 2.542,0.51 2.948,0.729 0.406,0.219 10 false MCS 1.292,2.333 1.99,2.667 0.698,0.333 10 false MRFG 1.948,2.323 2.51,2.573 0.563,0.25 10 false MSNG 2.625,2.313 3.135,2.604 0.51,0.292 10 false MCSG 0.76,1.458 1.094,1.615 0.333,0.156 10 false E12 4.302,0.573 4.688,0.781 0.385,0.208 10 false MRF 4.896,0.542 5.281,0.781 0.385,0.24 10 false MSN 5.531,0.542 5.99,0.833 0.458,0.292 10 false MCS 4.135,2.24 4.677,2.5 0.542,0.26 10 false MRFG 4.865,2.219 5.458,2.49 0.594,0.271 10 false MSNG 5.604,2.198 6.115,2.406 0.51,0.208 10 false MCSG 6.177,1.458 6.469,1.708 0.292,0.25 10 false E1 0.521,0.625 0.833,0.781 0.313,0.156 10 false *a 3.677,0.74 3.99,0.896 0.313,0.156 10 false *b
*a Front view of wire harness connector
(to Motor Resolver)
*b Front view of wire harness connector
(to Inverter with Converter Assembly)


Standard Resistance (Check for Open):
Tester Connection Switch Condition Specified Condition
E1-4 (MRF) - E12-1 (MRF) Power switch off Below 1 Ω
E1-11 (MRFG) - E12-4 (MRFG) Power switch off Below 1 Ω
E1-5 (MSN) - E12-2 (MSN) Power switch off Below 1 Ω
E1-12 (MSNG) - E12-5 (MSNG) Power switch off Below 1 Ω
E1-6 (MCS) - E12-3 (MCS) Power switch off Below 1 Ω
E1-13 (MCSG) - E12-6 (MCSG) Power switch off Below 1 Ω


Standard Resistance (Check for Short):
Tester Connection Switch Condition Specified Condition
E1-4 (MRF) or E12-1 (MRF) - Body ground and other terminals Power switch off 1 MΩ or higher
E1-11 (MRFG) or E12-4 (MRFG) - Body ground and other terminals Power switch off 1 MΩ or higher
E1-5 (MSN) or E12-2 (MSN) - Body ground and other terminals Power switch off 1 MΩ or higher
E1-12 (MSNG) or E12-5 (MSNG) - Body ground and other terminals Power switch off 1 MΩ or higher
E1-6 (MCS) or E12-3 (MCS) - Body ground and other terminals Power switch off 1 MΩ or higher
E1-13 (MCSG) or E12-6 (MCSG) - Body ground and other terminals Power switch off 1 MΩ or higher


HINT:

The motor resolver is not available separately. If it requires replacement, replace the hybrid vehicle transaxle assembly.



e.

Connect the motor resolver connector.


f.

Connect the inverter with converter assembly connector.

Result:
Proceed to
OK
NG




OK

REPLACE HYBRID VEHICLE TRANSAXLE ASSEMBLY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR