Home › Engine / Hybrid System › HYBRID / BATTERY CONTROL › HYBRID CONTROL SYSTEM › 2012.02–2015.04
RM2040EQ _51 Engine / Hybrid System _014692 HYBRID / BATTERY CONTROL _0074885 HYBRID CONTROL SYSTEM C

HYBRID / BATTERY CONTROL  HYBRID CONTROL SYSTEM  P324E-788  MG-ECU Power Relay Intermittent Circuit  


DESCRIPTION

If the MG ECU located in the inverter with converter assembly is reset due to a problem with the power source in the inverter, the power management control ECU will set this DTC.

DTC No. Detection Item DTC Detection Condition Trouble Area MIL Warning Indicate
P324E-788 MG-ECU Power Relay Intermittent Circuit Error in reset signal from the inverter assembly power source IC
·

Wire harness or connector

·

Inverter with converter assembly

·

Power management control ECU


Does not come on Master Warning Light:
Comes on

WIRING DIAGRAM

A254640E07
0.125,1.135 0.833,1.948 0.708,0.813 10 false to Auxiliary Battery 2.302,1.094 2.49,1.365 0.188,0.271 10 false 3 2.302,1.49 2.542,1.729 0.24,0.24 10 false 2 2.469,1.854 2.865,2.135 0.396,0.281 10 false IGCT 3.75,2.323 4.26,2.594 0.51,0.271 10 false MREL 3.292,3.313 3.667,3.521 0.375,0.208 10 false A39 3.302,3.51 4.552,4.188 1.25,0.677 10 false Power Management Control ECU 5.604,3.615 5.927,3.813 0.323,0.198 10 false A14 5.594,3.792 7.073,4.271 1.479,0.479 10 false Inverter with Converter Assembly 3.615,1.427 4.031,1.729 0.417,0.302 10 false INV 2.833,1.094 3.031,1.406 0.198,0.313 10 false 5 3.406,1.094 3.5,1.25 0.094,0.156 10 false 1 3.969,1.094 4.177,1.406 0.208,0.313 10 false 2 2.833,1.49 3.031,1.823 0.198,0.333 10 false 1 3.552,2.208 3.688,2.427 0.135,0.219 10 false 6 5.729,1.219 6.146,1.542 0.417,0.323 10 false +B 5.479,1.125 5.729,1.406 0.25,0.281 10 false 30 5.729,1.896 6.167,2.229 0.438,0.333 10 false +B2 5.5,1.771 5.688,2.073 0.188,0.302 10 false 31 5.729,2.49 6.323,2.865 0.594,0.375 10 false GND1 5.479,2.385 5.729,2.656 0.25,0.271 10 false 10 5.719,3.135 6.281,3.385 0.563,0.25 10 false GND2 5.469,3.052 5.688,3.292 0.219,0.24 10 false 11

CAUTION / NOTICE / HINT

CAUTION:
·

Before inspecting the high-voltage system or disconnecting the low voltage connector of the inverter with converter assembly, take safety precautions such as wearing insulated gloves and removing the service plug grip to prevent electrical shocks. After removing the service plug grip, put it in your pocket to prevent other technicians from accidentally reconnecting it while you are working on the high-voltage system.

·

After removing the service plug grip, wait for at least 10 minutes before touching any of the high-voltage connectors or terminals. After waiting for 10 minutes, check the voltage at the terminals in the inspection point in the inverter with converter assembly. The voltage should be 0 V before beginning work (See page Engine / Hybrid System>HYBRID / BATTERY CONTROL>HYBRID CONTROL SYSTEM>PRECAUTION).

HINT:

Waiting for at least 10 minutes is required to discharge the high-voltage capacitor inside the inverter with converter assembly.




NOTICE:

After turning the power switch off, waiting time may be required before disconnecting the cable from the negative (-) auxiliary battery terminal. Therefore, make sure to read the disconnecting the cable from the negative (-) auxiliary battery terminal notices before proceeding with work (See page General>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION).


PROCEDURE

1.CHECK DTC OUTPUT (HYBRID CONTROL)
a.

Connect the intelligent tester to the DLC3.


b.

Turn the power switch on (IG).


c.

Enter the following menus: Powertrain / Hybrid Control / DTC.

Powertrain > Hybrid Control > Trouble Codes
50001 236

d.

Check if DTCs are output.

Result:
Result Proceed to
P324E-788 only is output. A
U0110-159, 160, 656, 657 are also output. B



e.

Turn the power switch off.



A

2.CHECK CONNECTOR CONNECTION CONDITION (INVERTER WITH CONVERTER ASSEMBLY CONNECTOR)

B

2.CHECK CONNECTOR CONNECTION CONDITION (INVERTER WITH CONVERTER ASSEMBLY CONNECTOR)

OK

3.CHECK HARNESS AND CONNECTOR (INVERTER WITH CONVERTER ASSEMBLY - IGCT RELAY)

NG

CONNECT SECURELY

3.CHECK HARNESS AND CONNECTOR (INVERTER WITH CONVERTER ASSEMBLY - IGCT RELAY)
CAUTION:

Be sure to wear insulated gloves.


a.

Check that the service plug grip is not installed.

NOTICE:

After removing the service plug grip, do not turn the power switch on (READY), unless instructed by the repair manual because this may cause a malfunction.



b.

Disconnect connector A14 from the inverter with converter assembly.


c.

Remove the IGCT relay from the No. 2 engine room relay block.


d.

Measure the resistance according to the value(s) in the table below.

A259953C03
0.469,1.333 0.844,1.563 0.375,0.229 1.979,2.188 2.229,1.625 false 2.604,2.177 2.365,1.615 false 2.604,0.781 2.365,1.344 false 1.99,0.802 2.24,1.365 false 0.542,1.375 0.823,1.542 0.281,0.167 10 false A14 1.875,2.219 2.188,2.479 0.313,0.26 10 false +B 2.5,2.219 2.813,2.427 0.313,0.208 10 false +B2 1.802,0.604 2.219,0.802 0.417,0.198 10 false GND1 2.469,0.604 2.885,0.823 0.417,0.219 10 false GND2 0.552,0.448 0.75,0.708 0.198,0.26 10 false *a 4.375,0.448 4.594,0.719 0.219,0.271 10 false *1 5.99,1.083 6.188,1.323 0.198,0.24 10 false *2
*1 No. 2 Engine Room Relay Block *2 IGCT Relay
*a Front view of wire harness connector
(to Inverter with Converter Assembly)
- -


Standard Resistance (Check for Open):
Tester Connection Switch Condition Specified Condition
A14-30 (+B) - 5 (IGCT relay) Power switch off Below 1 Ω
A14-31 (+B2) - 5 (IGCT relay) Power switch off Below 1 Ω
A14-10 (GND1) - Body ground Power switch off Below 1 Ω
A14-11 (GND2) - Body ground Power switch off Below 1 Ω



e.

Install the IGCT relay.


f.

Connect the power management control ECU connector.

Result:
Proceed to
OK
NG




OK

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR