Home › Engine / Hybrid System › HYBRID / BATTERY CONTROL › HYBRID CONTROL SYSTEM › 2012.02–2015.04
RM2040EQ _51 Engine / Hybrid System _014692 HYBRID / BATTERY CONTROL _0074885 HYBRID CONTROL SYSTEM C

HYBRID / BATTERY CONTROL  HYBRID CONTROL SYSTEM  P3107-213  Lost Communication with Airbag System Control Module  


DESCRIPTION

The power management control ECU detects a problem in the collision signal line from the airbag sensor assembly and alerts the driver.


DTC No. Detection Item DTC Detection Condition Trouble Area MIL Warning Indicate
P3107-213 Lost Communication with Airbag System Control Module Short to GND in the communication circuit
·

Wire harness or connector

·

Airbag sensor assembly

·

Power management control ECU


Does not come on Master Warning Light:
Comes on

WIRING DIAGRAM

A254875E06
4.906,0.996 5.318,1.157 0.412,0.161 10 ABFS 1.925,0.996 2.369,1.157 0.444,0.161 10 GSW2 2.158,1.304 2.365,1.465 0.207,0.161 10 E1 4.654,0.996 4.856,1.157 0.202,0.161 10 29 4.45,2.075 4.742,2.236 0.292,0.161 10 I3 4.45,2.222 6.571,2.383 2.121,0.161 10 Power Management Control ECU 0.968,2.075 1.26,2.236 0.292,0.161 10 I47 0.968,2.222 2.562,2.383 1.594,0.161 10 Airbag Sensor Assembly 2.397,0.998 2.603,1.159 0.207,0.161 10 14 2.397,1.306 2.603,1.467 0.207,0.161 10 25 5.555,0.427 5.847,0.588 0.292,0.161 10 +B

PROCEDURE

1.CHECK DTC OUTPUT (SRS AIRBAG)
a.

Connect the intelligent tester to the DLC3.


b.

Turn the power switch on (IG).


c.

Enter the following menus: Body / SRS Airbag / DTC.


d.

Check if DTCs are output.

Body Electrical > SRS Airbag > Trouble Codes
50001 188
Result:
Result Proceed to
Airbag system DTCs are not output. A
Airbag system DTCs are output. B



e.

Turn the power switch off.



A

2.CHECK AIRBAG SENSOR ASSEMBLY (CHECK WAVEFORM)

B

2.CHECK AIRBAG SENSOR ASSEMBLY (CHECK WAVEFORM)
a.

Connect an oscilloscope between the airbag sensor assembly terminals specified in the table below.


b.

Turn the power switch on (READY).


c.
A258640C12
1.417,1.802 1.677,1.979 0.26,0.177 1.552,1.344 0.958,1.896 false 1.625,1.208 2.229,1.906 false 0.156,0.125 0.469,0.323 0.313,0.198 10 *a 0.844,1.927 1.052,2.125 0.208,0.198 10 E1 2.083,1.938 2.542,2.104 0.458,0.167 10 GSW2 1.458,1.823 1.729,1.979 0.271,0.156 10 I47 2.896,3.427 3.24,3.594 0.344,0.167 10 GND
*a Component with harness connected
(Airbag Sensor Assembly)


Measure the waveform.

Item Contents
Terminal I47-14 (GSW2) - I47-25 (E1)
Equipment Setting 5 V/DIV., 500 ms./DIV.
Condition Power switch on (READY)

Result:
Result Proceed to
The waveform appears as shown in the illustration. A
The waveform differs from the one shown in the illustration. B



d.

Turn the power switch off.



A

3.CLEAR DTC

B

6.CHECK AIRBAG SENSOR ASSEMBLY
3.CLEAR DTC

NEXT

4.CHECK DTC OUTPUT (HYBRID CONTROL)
4.CHECK DTC OUTPUT (HYBRID CONTROL)
a.

Connect the intelligent tester to the DLC3.


b.

Turn the power switch on (IG).


c.

Enter the following menus: Powertrain / Hybrid Control / DTC.


d.

Check if DTCs are output.

Powertrain > Hybrid Control > Trouble Codes
50001 236
Result:
Result Proceed to
P3107-213 is not output. A
P3107-213 is output. B



e.

Turn the power switch off.



A

5.CHECK FOR INTERMITTENT PROBLEMS

B

5.CHECK FOR INTERMITTENT PROBLEMS

OK

NG

REPAIR OR REPLACE MALFUNCTIONING PARTS, COMPONENT AND AREA

6.CHECK AIRBAG SENSOR ASSEMBLY
a.

Disconnect connector I47 from the airbag sensor assembly.


b.
A256535C08
1.281,0.188 1.698,0.427 0.417,0.24 1.531,1.177 1.052,1.688 false 1.604,1.031 1.969,1.677 false 0.188,0.094 0.885,0.542 0.698,0.448 10 false *a 1.792,1.729 2.552,2.052 0.76,0.323 10 false GSW2 0.938,1.729 1.448,2.094 0.51,0.365 10 false E1 1.354,0.229 2.094,0.688 0.74,0.458 10 false I47
*a Component without harness connected
(Airbag Sensor Assembly)


Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
I47-14 (GSW2) - I47-25 (E1) Power switch off 10 kΩ or higher



c.

Reconnect the E14 airbag sensor assembly connector.


Result:
Proceed to
OK
NG



OK

7.CHECK HARNESS AND CONNECTOR (POWER MANAGEMENT CONTROL ECU - AIRBAG SENSOR ASSEMBLY)

NG

7.CHECK HARNESS AND CONNECTOR (POWER MANAGEMENT CONTROL ECU - AIRBAG SENSOR ASSEMBLY)
a.

Disconnect connector I3 from the power management control ECU.


b.
A256537C08
0.583,1.625 1,1.865 0.417,0.24 0.083,0.052 0.344,0.229 0.26,0.177 10 false *a 0.667,1.677 1.219,1.979 0.552,0.302 10 false I47
*a Component without harness connected
(Airbag Sensor Assembly)


Disconnect connector I47 from the airbag sensor assembly.


c.
A258641C04
1.375,1.594 1.615,1.771 0.24,0.177 0.885,3.76 1.156,3.969 0.271,0.208 2.25,1.823 2.542,2.125 false 1.677,3.833 2.063,4.302 false 0.073,0.042 0.385,0.24 0.313,0.198 10 *a 0.104,2.333 0.417,2.531 0.313,0.198 10 *b 1.448,1.615 1.594,1.771 0.146,0.156 10 I3 2.438,2.156 2.844,2.323 0.406,0.167 10 ABFS 0.948,3.792 1.208,3.938 0.26,0.146 10 I47 1.906,4.333 2.344,4.5 0.438,0.167 10 GSW2
*a Rear view of wire harness connector
(to Power Management Control ECU)
*b Rear view of wire harness connector
(to Airbag Sensor Assembly)


Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
I3-29 (ABFS) or I47-14 (GSW2) - Body ground and other terminals Power switch off 10 kΩ or higher



d.

Connect the airbag sensor assembly connector.


e.

Connect the power management control ECU connector.


Result:
Proceed to
OK
NG



OK

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR