Perform "Inspection After Repair" after replacing the cylinder head sub-assembly.
Click hereEngine / Hybrid System>2AR-FXE ENGINE CONTROL>SFI SYSTEM>INITIALIZATION
1.INSTALL SPARK PLUG TUBE
When using a new cylinder head, the spark plug tubes must be replaced.
Apply adhesive onto the shaded area of a new spark plug tube.
Toyota Genuine Adhesive 1324, Three Bond 1324 or equivalent.
1.0 to 3.0 mm (0.0394 to 0.118 in.)
Install the spark plug tube within 3 minutes after applying adhesive.
Be careful not to deform the spark plug tube.
Be careful not to expose the seal to coolant for at least 1 hour after installing it.
| *a | Cylinder Head Casting Surface |
Using a wooden block and hammer, tap in the spark plug tube to the specified protrusion height.
112 mm (4.41 in.)
To avoid tapping in the spark plug tube too far, measure the protrusion height while tapping it.
17159
2.INSTALL CYLINDER HEAD STUD BOLT
Using an E7 "TORX" socket wrench, install the 5 cylinder head stud bolts.
11117E
3.INSTALL NO. 1 STRAIGHT SCREW PLUG
Using a 10 mm hexagon wrench, install 3 new gaskets and the 3 No.1 straight screw plugs.
11117F
4.INSTALL NO. 2 STRAIGHT SCREW PLUG
Using a 14 mm hexagon wrench, install a new gasket and the No. 2 straight screw plug.
13734
5.INSTALL VALVE SPRING SEAT
Install the valve spring seats to the cylinder head.
13711E
6.INSTALL VALVE STEM OIL SEAL
| *a | Intake |
| *b | Exhaust |
| *c | Mark "NOK" |
| *d | Gray |
| *e | Black |
Apply a light coat of engine oil to new oil seals.
Pay attention when installing the intake and exhaust oil seals. For example, installing the intake oil seal onto the exhaust side or installing the exhaust oil seal onto the intake side can cause installation problems later.
The intake valve oil seals are gray and the exhaust valve oil seals are black.
| *a | CORRECT |
| *b | INCORRECT |
Using SST, push in the intake and exhaust valve oil seals.
Failure to use SST will cause the seal to be damaged or improperly seated.
13711
7.INSTALL INTAKE VALVE
Type A and Type B can be distinguished by the shape of the compression spring.
| *A | Type A
(Compression Spring Shape: Straight) |
*B | Type B
(Compression Spring Shape: Tapered) |
| *1 | No. 1 Valve Rocker Arm Sub-assembly | *2 | Valve Spring Retainer |
| *3 | Compression Spring | *4 | Valve Lash Adjuster Assembly |
| *a | 30 mm (1.18 in.) or more |
Apply plenty of engine oil to the tip area of the intake valve shown in the illustration.
Type A
Install the 8 intake valves, 8 compression springs and 8 valve spring retainers to the cylinder head sub-assembly.
Install the same parts in the same combination to their original locations.
Using SST and wooden blocks, compress the compression spring and install the 16 valve spring retainer locks.
Type B:
| *a | Narrow |
| *b | Wide |
Install the 8 intake valves, 8 compression springs and 8 valve spring retainers to the cylinder head sub-assembly.
Install the same parts in the same combination to their original locations.
Using SST and wooden blocks, compress the compression spring and install the 16 valve spring retainer locks.
Using a plastic-faced hammer, lightly tap the valve stem tip to ensure a proper fit.
Be careful not to damage the retainer.
13715
8.INSTALL EXHAUST VALVE
Type A and Type B can be distinguished by the shape of the compression spring.
| *A | Type A
(Compression Spring Shape: Straight) |
*B | Type B
(Compression Spring Shape: Tapered) |
| *1 | No. 1 Valve Rocker Arm Sub-assembly | *2 | Valve Spring Retainer |
| *3 | Compression Spring | *4 | Valve Lash Adjuster Assembly |
| *a | 30 mm (1.18 in.) or more |
Apply plenty of engine oil to the tip area of the exhaust valve shown in the illustration.
Type A:
Install the 8 exhaust valves, 8 compression springs and 8 valve spring retainers to the cylinder head sub-assembly.
Install the same parts in the same combination to their original locations.
Using SST and wooden blocks, compress the compression spring and install the 16 valve spring retainer locks.
Type B:
| *a | Narrow |
| *b | Wide |
Install the 8 exhaust valves, 8 compression springs and 8 valve spring retainers to the cylinder head sub-assembly.
Install the same parts in the same combination to their original locations.
Using SST and wooden blocks, compress the compression spring and install the 16 valve spring retainer locks.
Using a plastic-faced hammer, lightly tap the valve stem tip to ensure a proper fit.
Be careful not to damage the retainer.