Home › Engine / Hybrid System › 2AR-FXE EMISSION CONTROL › EMISSION CONTROL SYSTEM
RM2040EQ _51 Engine / Hybrid System _014695 2AR-FXE EMISSION CONTROL _0074917 EMISSION CONTROL SYSTEM G

2AR-FXE EMISSION CONTROL  EMISSION CONTROL SYSTEM  ON-VEHICLE INSPECTION  


PROCEDURE

Hide 1.VISUALLY INSPECT HOSES, CONNECTIONS AND GASKETS

a.

Inspect the hoses and gaskets for scratches, cracks or air/oil leaks from the connecting parts.

HINT:

If the hoses or gaskets are damaged or some of the connections are loose, they may cause an engine stall or malfunction.



Hide 2.INSPECT EVAPORATIVE EMISSION CONTROL SYSTEM

a.

Connect the intelligent tester to the DLC3.


b.

Put the engine in inspection mode (maintenance mode).

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>INSPECTION MODE PROCEDURE


c.

Start the engine and disconnect the fuel vapor feed hose from the purge VSV.

A306187C01
2.594,2.229 2.427,2.229 2.427,2.229 2.729,1.677 false 3.219,1.417 3.396,2.219 3.396,2.219 3.208,2.219 false 1.365,2.344 1.563,2.344 1.563,2.344 1.76,1.646 false 0.885,1.135 1.188,0.417 1.188,0.417 1.417,0.417 false 0.5,2.583 0.25,2.583 0.25,2.583 0.75,1.771 false 3.333,0.792 3.646,0.99 0.313,0.198 10 false *a 2.385,0.792 2.698,0.99 0.313,0.198 10 false *a 3.073,1.813 3.385,2.01 0.313,0.198 10 false *b 2.635,2.146 2.948,2.344 0.313,0.198 10 false *1 3.052,2.146 3.365,2.344 0.313,0.198 10 false *2 1.198,2.26 1.51,2.458 0.313,0.198 10 false *3 1.49,0.344 1.802,0.542 0.313,0.198 10 false *4 0.563,2.5 0.875,2.698 0.313,0.198 10 false *2
*1 Retainer *2 Fuel Tube Connector
*3 Pipe *4 O-ring
*a Pinch *b Pull


NOTICE:
·

Remove any dirt or foreign matter on the fuel tube connector before performing this work.

·

Do not allow any scratches or foreign matter to get on the parts when disconnecting them as the fuel tube connector has an O-ring that seals the pipe.

·

Perform this work by hand. Do not use any tools.

·

Protect the disconnected parts by covering them with plastic bags after disconnecting the fuel vapor feed hose.




d.

Enter the following menus: Powertrain / Engine and ECT / Active Test / Activate the VSV for Evap Control.

Powertrain > Engine and ECT > Active Test
Tester Display
Activate the VSV for Evap Control
50004 234 6

e.

Check that vacuum occurs at the purge VSV port.


f.

If vacuum does not occur, check the following items:

·

Purge VSV (for canister purge)

·

Clogs in the fuel vapor feed hose connecting the intake air surge tank and purge VSV

·


g.
A262464C01
0.79,3.406 0.96,3.559 0.17,0.153 10 *1 1.896,3.865 2.066,4.018 0.17,0.153 10 *a 1.494,3.488 0.989,3.488 false
*1 Retainer
*a Push


Exit Active Test mode and reconnect the fuel vapor feed hose.

NOTICE:
·

Check that there are no scratches or foreign matter around the connected part of the fuel tube connector and pipe before performing this work.

·

Connect the quick connector and push the retainer in until the retainer makes a "click" sound to lock the claws of the retainer.

·

After connecting the fuel vapor feed hose to the fuel tube connector, check that the fuel vapor feed hose is securely connected by pulling on the fuel tube connector and the fuel vapor feed hose.




h.

Enter the following menus: Powertrain / Engine and ECT / Data List / EVAP Purge VSV.

Powertrain > Engine and ECT > Data List
Tester Display
EVAP Purge VSV
50003 234 217

i.

Warm up the engine and drive the vehicle.


j.

Confirm that the purge VSV opens.

If the result is not as specified, replace the purge VSV, wire harness or ECM.