Home › Engine / Hybrid System › 2AR-FXE EMISSION CONTROL › CANISTER
RM2040EQ _51 Engine / Hybrid System _014695 2AR-FXE EMISSION CONTROL _0074919 CANISTER G

2AR-FXE EMISSION CONTROL  CANISTER  ON-VEHICLE INSPECTION  


PROCEDURE

Hide 77740 1.INSPECT CHARCOAL CANISTER ASSEMBLY

a.

Visually check the charcoal canister.

i.

Visually check the charcoal canister for cracks or damage.

HINT:

If cracks or damage are found, replace the charcoal canister assembly.




b.

Check charcoal canister operation under positive pressure.

i.
A255917
0.688,0.833 0.938,0.833 0.938,0.833 1.333,1.229 false 0.885,2.531 0.885,2.813 false 0.5,0.75 0.708,0.938 0.208,0.188 10 true *1 0.792,2.813 1.208,3.083 0.417,0.271 10 false *2 0.333,2.125 0.531,2.302 0.198,0.177 10 true *a
*1 Vent Line Hose
*2 Test Hose
*a Air


Disconnect the vent line hose from the charcoal canister assembly. Close the vent line hose using a hose plug or a similar part.


ii.

Connect a test hose to the charcoal canister assembly.


iii.

Blow 5 kPa (0.1 kgf/cm2, 0.7 psi) of air into the hose.

Standard:

Air can be blown through the canister.


HINT:

If the standard is not as specified, replace the charcoal canister assembly.




c.

Check charcoal canister operation under vacuum.

i.

Disconnect the vent line hose from the charcoal canister assembly. Close the vent line hose using a hose plug or a similar part.


ii.

Connect a test hose to the charcoal canister assembly.


iii.

Connect a vacuum pump to the test hose.


iv.
A255918
0.698,0.333 0.885,0.333 0.885,0.333 1.344,0.792 false 1.417,2.313 1.417,2.906 false 0.51,0.26 0.75,0.458 0.24,0.198 10 true *1 1.333,2.938 1.698,3.198 0.365,0.26 10 false *2
*1 Vent Line Hose
*2 Test Hose


Using the vacuum pump, apply vacuum and check the indicator.

Standard:

The vacuum pump indicator does not move from its initial position.


HINT:
·

The indicator may move when applying vacuum. If the indicator quickly returns to its initial position, the charcoal canister is operating normally.

·

If the standard is not as specified, replace the charcoal canister assembly.





d.

Check for clogs in the air filter (when not using the intelligent tester).

i.

Disconnect the vent line hose from the charcoal canister assembly. Close the vent line hose using a hose plug or a similar part.


ii.

Connect a test hose to the charcoal canister assembly.


iii.

Connect a vacuum pump to the test hose.


iv.

Start the engine.


v.

Warm up the engine.


vi.

After warm-up, idle the engine for 15 minutes and check the vacuum pump indicator.

Standard:

The vacuum pump indicator does not move from its initial position.


HINT:

The indicator may move when the purge VSV opens to vacuum. If the indicator quickly returns to its initial position, the charcoal canister is operating normally.




e.

Check for clogs in the air filter (when using the intelligent tester).

HINT:

When performing an Active Test of the purge VSV using the intelligent tester, it is not necessary to warm-up and idle the engine for 15 minutes.


i.

Disconnect the vent line hose from the charcoal canister assembly. Close the vent line hose using a hose plug or a similar part.


ii.

Connect a test hose to the charcoal canister assembly.


iii.

Connect a vacuum pump to the test hose.


iv.

Connect the intelligent tester to the DLC3.


v.

Start the engine.


vi.

Enter the following menus: Powertrain / Engine and ECT / Active Test / Activate the VSV for Evap Control.

Powertrain > Engine and ECT > Active Test
Tester Display
Activate the VSV for Evap Control
50004 234 6

vii.

Perform the Active Test with the engine idling.

Standard:

The vacuum pump indicator does not move from its initial position.


HINT:

The indicator may move when the purge VSV opens to vacuum. If the indicator quickly returns to its initial position, the charcoal canister is operating normally.