Home › Engine / Hybrid System › 2AR-FXE INTAKE / EXHAUST › EXHAUST MANIFOLD
RM2040EQ _51 Engine / Hybrid System _014696 2AR-FXE INTAKE / EXHAUST _0074924 EXHAUST MANIFOLD A

2AR-FXE INTAKE / EXHAUST  EXHAUST MANIFOLD  INSTALLATION  


PROCEDURE

Hide 17168 1.INSTALL NO. 2 EXHAUST MANIFOLD HEAT INSULATOR

a.

Install the No. 2 exhaust manifold heat insulator with the 2 bolts.

Torque:
14 N*m (138 kgf*cm, 10 ft.*lbf)


Hide 25051 2.INSTALL EXHAUST MANIFOLD CONVERTER SUB-ASSEMBLY

a.

Set a new gasket to the cylinder head sub-assembly.


b.

Temporarily install the exhaust manifold converter sub-assembly with the 5 nuts.


c.

Temporarily install the No. 2 manifold stay and manifold stay with the 2 bolts and 2 nuts.


d.
A195979
1.438,1.677 1.594,1.865 0.156,0.188 10 true 1 0.625,0.01 0.792,0.177 0.167,0.167 10 true 2 2.75,0.042 2.927,0.24 0.177,0.198 10 true 3 0.302,1.656 0.469,1.833 0.167,0.177 10 true 4 3.146,1.635 3.313,1.823 0.167,0.188 10 true 5

Tighten the 5 nuts in the order shown in the illustration.

Torque:
35 N*m (357 kgf*cm, 26 ft.*lbf)


Hide 17118 3.INSTALL MANIFOLD STAY

a.
A257339
0.833,0.344 1,0.542 0.167,0.198 10 true 1 1.917,0.438 2.125,0.646 0.208,0.208 10 true 2

Tighten the bolt and nut in the order shown in the illustration.

Torque:
43 N*m (438 kgf*cm, 32 ft.*lbf)


Hide 17139 4.INSTALL NO. 2 MANIFOLD STAY

a.
A257340
2.719,0.49 2.896,0.677 0.177,0.188 10 true 1 1.125,1.458 1.302,1.646 0.177,0.188 10 true 2

Tighten the bolt and nut in the order shown in the illustration.

Torque:
43 N*m (438 kgf*cm, 32 ft.*lbf)


Hide 25612 5.INSTALL NO. 2 EGR PIPE

a.

Install 2 new gaskets to the No. 2 EGR pipe.


b.

Install the No. 2 EGR pipe with the 2 bolts and 2 nuts.

Torque:
36 N*m (367 kgf*cm, 26 ft.*lbf)


Hide 25586 6.INSTALL NO. 1 MANIFOLD CONVERTER INSULATOR

a.

Install the No. 1 manifold converter insulator with the 3 bolts.

Torque:
14 N*m (138 kgf*cm, 10 ft.*lbf)


Hide 17167 8.INSTALL NO. 1 EXHAUST MANIFOLD HEAT INSULATOR

a.

Install the No. 1 exhaust manifold heat insulator with the 4 bolts.

Torque:
12 N*m (122 kgf*cm, 9 ft.*lbf)


Hide 17410 9.INSTALL FRONT EXHAUST PIPE ASSEMBLY

a.
A077857

Using a vernier caliper, measure the free length of the compression spring.

Standard 42.0 mm (1.65 in.)
Minimum 40.5 mm (1.60 in.)

HINT:

If the length is less than the minimum, replace the compression spring.



b.

Fully insert a new gasket to the exhaust manifold converter sub-assembly.


c.
A104635
0.917,0.229 1.125,0.229 1.125,0.229 1.583,0.688 false 2.167,1.625 2.167,1.958 false 2.698,0.958 3.156,0.958 false 2.094,1.99 2.615,2.177 0.521,0.188 10 false *3 3.208,0.865 3.417,1.104 0.208,0.24 10 false *2 0.719,0.146 1.125,0.427 0.406,0.281 10 false *1
*1 Exhaust Manifold Converter Sub-assembly
*2 Wooden Block
*3 Gasket


Using a plastic hammer and wooden block, tap in the new gasket until its surface is flush with the exhaust manifold converter sub-assembly.

NOTICE:
·

Be sure to install the gasket in the correct direction.

·

Do not reuse the gasket.

·

Do not damage the gasket.

·

Do not push in the gasket by using the exhaust pipe when connecting it.




d.

Install a new gasket to the front exhaust pipe assembly.


e.

Connect the front exhaust pipe assembly to the exhaust pipe support.


f.
A258941
0.543,0.102 0.693,0.252 0.15,0.15 10 *1 2.694,0.132 2.844,0.282 0.15,0.15 10 *3 0.605,1.113 0.754,1.263 0.15,0.15 10 *2 0.419,1.433 0.568,1.582 0.15,0.15 10 *a 1.146,0.584 0.883,0.184 0.883,0.184 0.733,0.184 false 0.79,1.195 0.925,1.195 0.925,1.195 1.112,0.903 false 2.411,0.76 2.503,0.215 2.503,0.215 2.676,0.215 false
*1 Exhaust Manifold Converter Sub-assembly
*2 Front Exhaust Pipe Assembly
*3 Gasket
*a Space between flanges: 8.5 mm (0.335 in.)


Install the front exhaust pipe assembly with the 2 compression springs, 2 bolts and 2 nuts.

Torque:
43 N*m (438 kgf*cm, 32 ft.*lbf)

HINT:

After the installation, check that the gaps between the flanges of the exhaust manifold converter sub-assembly and front exhaust pipe assembly are consistent front-to-rear and left-to-right.



g.

Connect the heated oxygen sensor connector.


Hide 51442C 10.INSTALL ENGINE UNDER COVER LH

Hide 53852K 11.INSTALL FRONT WHEEL OPENING EXTENSION PAD LH

Hide 51441C 12.INSTALL ENGINE UNDER COVER RH

Hide 53851Z 13.INSTALL FRONT WHEEL OPENING EXTENSION PAD RH

Hide 14.INSPECT FOR EXHAUST GAS LEAK