Home › Engine / Hybrid System › CRUISE CONTROL › CRUISE CONTROL SYSTEM › 2012.02–2015.04
RM2040EQ _51 Engine / Hybrid System _014700 CRUISE CONTROL _0074941 CRUISE CONTROL SYSTEM C

CRUISE CONTROL  CRUISE CONTROL SYSTEM  P0571  Brake Switch "A" Circuit  


DESCRIPTION

When the brake pedal is depressed, the stop light switch assembly sends a signal to the power management control ECU. When the power management control ECU receives this signal, it cancels cruise control system control of vehicle speed. The fail-safe function operates to enable normal driving even if there is a malfunction in the stop light signal circuit. The cancellation condition occurs when voltage is applied to terminal STP. When the brake is applied, voltage is normally applied to terminal STP of the power management control ECU through the STOP fuse and the stop light switch assembly, and the power management control ECU turns the cruise control off.

DTC No. Detection Item DTC Detection Condition Trouble Area
P0571 Brake Switch "A" Circuit Voltage of STP signal and that of ST1- terminal of power management control ECU are less than 1 V for 0.5 seconds or more
·

Stop light switch assembly

·

Stop light switch assembly circuit

·

Power management control ECU



WIRING DIAGRAM

E235557
3.552,1.302 5.313,1.49 1.76,0.188 10 false Stop Light Switch Assembly 3.552,1.146 3.833,1.292 0.281,0.146 10 false A33 0.667,3.969 1.219,4.427 0.552,0.458 10 false Auxiliary Battery 6.094,2.865 6.438,3.021 0.344,0.156 10 false IG2D 5.76,4.115 7.063,4.427 1.302,0.313 10 false Power Management Control ECU 5.76,3.948 6.104,4.104 0.344,0.156 10 false A39 4.177,3.083 4.448,3.24 0.271,0.156 10 false IG2 6.073,0.448 6.5,0.615 0.427,0.167 10 false STP 2.448,0.604 2.875,0.771 0.427,0.167 10 false STOP 0.552,2.896 1,3.052 0.448,0.156 10 false MAIN 2.021,2.604 2.74,2.771 0.719,0.167 10 false IG2-MAIN 5.885,2.76 6.01,2.927 0.125,0.167 10 false 2 3.854,0.354 3.979,0.521 0.125,0.167 10 false 2 3.854,0.792 3.979,0.958 0.125,0.167 10 false 4 4.542,0.354 4.667,0.521 0.125,0.167 10 false 1 4.542,0.792 4.667,0.958 0.125,0.167 10 false 3 2.229,1.052 3.229,1.219 1,0.167 10 false ECU-IG2 No. 3 0.542,1.469 1.042,1.635 0.5,0.167 10 false DC/DC 5.813,0.354 6.031,0.521 0.219,0.167 10 false 23 5.885,0.792 5.99,0.958 0.104,0.167 10 false 7 6.073,0.875 6.5,1.042 0.427,0.167 10 false ST1-

CAUTION / NOTICE / HINT

NOTICE:

Inspect the fuses for circuits related to this system before performing the following procedure.


PROCEDURE

1.INSPECT STOP LIGHT SWITCH ASSEMBLY (POWER SOURCE)
a.
E144327C08
0.469,2.167 0.781,2.406 0.313,0.24 0.5,2.208 0.958,2.406 0.458,0.198 10 false A33 0.167,0.208 0.625,0.406 0.458,0.198 10 false *a
*a Front view of wire harness connector
(to Stop Light Switch Assembly)


Disconnect the stop light switch assembly connector.


b.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
A33-2 - Body ground Always 11 to 14 V



Result:
Proceed to
OK
NG



OK

2.INSPECT STOP LIGHT SWITCH ASSEMBLY (POWER SOURCE)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR (STOP LIGHT SWITCH ASSEMBLY - AUXILIARY BATTERY)

2.INSPECT STOP LIGHT SWITCH ASSEMBLY (POWER SOURCE)
a.
E144327C08
0.469,2.167 0.781,2.406 0.313,0.24 0.5,2.208 0.958,2.406 0.458,0.198 10 false A33 0.167,0.208 0.625,0.406 0.458,0.198 10 false *a
*a Front view of wire harness connector
(to Stop Light Switch Assembly)


Turn the power switch on (IG).


b.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
A33-4 - Body ground Power switch on (IG) 11 to 14 V



Result:
Proceed to
OK
NG



OK

3.INSPECT STOP LIGHT SWITCH ASSEMBLY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR (STOP LIGHT SWITCH ASSEMBLY - IG2 RELAY)

3.INSPECT STOP LIGHT SWITCH ASSEMBLY
a.
E145496C12
0.156,0.219 0.469,0.417 0.313,0.198 10 false *a 0.667,2.552 0.979,2.75 0.313,0.198 10 false *b 1.281,2.573 1.594,2.771 0.313,0.198 10 false *c
*a Component without harness connected
(Stop Light Switch Assembly)
*b Not pushed
*c Pushed


Remove the stop light switch assembly.

Click hereVehicle Exterior>LIGHTING (EXT)>STOP LIGHT SWITCH>REMOVAL


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Switch Condition Specified Condition
1 - 2 Switch pin not pushed Below 0.1 Ω
3 - 4 Switch pin not pushed 10 kΩ or higher
1 - 2 Switch pin pushed 10 kΩ or higher
3 - 4 Switch pin pushed Below 200 Ω



Result:
Proceed to
OK
NG



OK

4.CHECK HARNESS AND CONNECTOR (STOP LIGHT SWITCH ASSEMBLY - POWER MANAGEMENT CONTROL ECU)

NG

REPLACE STOP LIGHT SWITCH ASSEMBLY

4.CHECK HARNESS AND CONNECTOR (STOP LIGHT SWITCH ASSEMBLY - POWER MANAGEMENT CONTROL ECU)
a.

Disconnect the power management control ECU connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance (Check for Open):
Tester Connection Condition Specified Condition
A39-23 (STP) - A33-1 Always Below 1 Ω
A39-7 (ST1-) - A33-3 Always Below 1 Ω


Standard Resistance (Check for Short):
Tester Connection Condition Specified Condition
A39-23 (STP) or A33-1 - Body ground Always 10 kΩ or higher
A39-7 (ST1-) or A33-3 - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR (POWER MANAGEMENT CONTROL ECU - STOP LIGHT SWITCH ASSEMBLY)