Home › Drivetrain › P314 HYBRID TRANSMISSION / TRANSAXLE › SHIFT LEVER
RM2040EQ _52 Drivetrain _014701 P314 HYBRID TRANSMISSION / TRANSAXLE _0074952 SHIFT LEVER G

P314 HYBRID TRANSMISSION / TRANSAXLE  SHIFT LEVER  INSPECTION  


PROCEDURE

Hide 33560C 1.INSPECT LOWER SHIFT LEVER ASSEMBLY

a.
C245039
1.385,1.5 1.552,0.542 1.552,0.542 1.656,0.542 true 1.313,1.5 1.146,0.542 1.146,0.542 1.042,0.542 true 0.844,0.458 1.021,0.625 0.177,0.167 10 false IG 1.698,0.458 2.042,0.625 0.344,0.167 10 false STP 0.052,0.052 0.302,0.26 0.25,0.208 10 true *a
*a Component with harness connected
(Shift Lock Control ECU)


Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
5 (IG) - Body ground Power switch on (IG) 11 to 14 V
Power switch off Below 1 V
4 (STP) - Body ground Brake pedal depressed 11 to 14 V
Brake pedal released Below 1 V


HINT:

Do not disconnect the shift lock control unit assembly connector.



b.
C245039
1.594,1.5 1.719,0.385 1.719,0.385 1.813,0.385 true 0.063,0.052 0.313,0.292 0.25,0.24 10 true *a 1.865,0.313 2.01,0.479 0.146,0.167 10 false E
*a Component with harness connected
(Shift Lock Control ECU)


Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
1 (E) - Body ground Always Below 1 Ω


HINT:

Do not disconnect the shift lock control unit assembly connector.



c.

Inspect shift lock solenoid

i.
C244959

Disconnect the shift lock solenoid connector.


ii.
C197452
1.375,1.24 0.729,1.635 true 1.583,1.229 1.354,1.625 true 1.844,1.229 2.125,1.646 true 2.083,1.219 2.656,1.625 true 0.063,0.052 0.281,0.24 0.219,0.188 10 false *a 0.521,1.656 0.99,1.875 0.469,0.219 10 false SLS+ 1.208,1.656 1.635,1.865 0.427,0.208 10 false SLS- 2.094,1.677 2.375,1.875 0.281,0.198 10 false E2 2.667,1.646 2.885,1.854 0.219,0.208 10 false P
*a Front view of wire harness connector
(to Shift Lock Solenoid)


Measure the resistance according to the value(s) in the table below when the shift lever is moved to each position.

Standard Resistance:
Tester Connection Shift Lever Position Specified Condition
4 (P) - 3 (E2) P 10 kΩ or higher
4 (P) - 3 (E2) Other than P Below 1 Ω


·

If the result is not as specified, replace the shift lock control unit assembly.

·

If the shift lock does not operate when the power source of the shift lock control unit assembly is normal and the resistance between the body ground and the shift lock solenoid is as specified, replace the shift lock control unit assembly.



iii.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
1 (SLS+) - 2 (SLS-) Always 112 Ω


·

If the result is not as specified, replace the shift lock control unit assembly.

·

If the shift lock does not operate when the power source of the shift lock control unit assembly is normal and the resistance between the body ground and the shift lock solenoid is as specified, replace the shift lock control unit assembly.