Home › Drivetrain › DRIVE SHAFT / PROPELLER SHAFT › FRONT DRIVE SHAFT ASSEMBLY
RM2040EQ _52 Drivetrain _014702 DRIVE SHAFT / PROPELLER SHAFT _0074955 FRONT DRIVE SHAFT ASSEMBLY A

DRIVE SHAFT / PROPELLER SHAFT  FRONT DRIVE SHAFT ASSEMBLY  REASSEMBLY  


PROCEDURE

Hide 43410C 1.INSTALL FRONT DRIVE SHAFT BEARING (for RH Side)

a.
C092032C02
1.063,0.292 1.323,0.292 1.323,0.292 1.323,0.604 false 0.844,1.177 1.156,1.177 1.156,1.177 1.156,1.313 false 2.344,1.396 2.156,1.396 2.156,1.396 2.156,1.552 false 0.875,0.208 1.208,0.469 0.333,0.26 10 false *1 0.552,1.094 1.01,1.354 0.458,0.26 10 false SST 2.396,1.302 2.792,1.583 0.396,0.281 10 false SST
*1 Steel Plate


Using SST, a steel plate and a press, install a new front drive shaft bearing.

SST
09527-10011  

NOTICE:

The bearing should be completely installed.



b.
C092033

Using a snap ring expander, install a new drive shaft hole snap ring.


Hide 41336D 2.INSTALL FRONT DRIVE SHAFT DUST COVER RH

a.
C129109C01
1.625,0.302 1.823,0.104 1.823,0.104 1.927,0.104 false 2.896,1.313 3.146,1.49 0.25,0.177 10 (A) 1.979,0.042 2.219,0.188 0.24,0.146 10 *1
*1 Steel Plate


Using a steel plate and a press, install a new front drive shaft dust cover RH until dimension (A) from the tip of the front drive inboard joint assembly to the front drive shaft dust cover RH meets the specification.

Dimension (A):

110.0 to 111.0 mm (4.33 to 4.37 in.)


NOTICE:
·

The dust cover should be completely installed.

·

Be careful not to damage the front drive shaft dust cover RH.




Hide 41336E 3.INSTALL FRONT DRIVE SHAFT DUST COVER LH

a.
F041033C01
0.49,0.635 0.49,0.417 0.49,0.417 0.365,0.417 false 0.188,0.354 0.479,0.604 0.292,0.25 10 false *1
*1 Steel Plate


Using a steel plate and a press, install a new front drive shaft dust cover LH.

NOTICE:
·

The dust cover should be completely installed.

·

Be careful not to damage the front drive shaft dust cover LH.




Hide 4.INSTALL FRONT AXLE OUTBOARD JOINT BOOT

a.
C166359C01
1.917,0.885 2.427,0.375 2.427,0.375 2.792,0.375 false 2.823,0.281 3.104,0.552 0.281,0.271 10 false *1
*1 Protective Tape


Wrap the splines of the front drive outboard joint shaft assembly with protective tape to prevent the boot from being damaged.


b.
C274276C01
1.26,1.875 1.26,1.458 false 1.729,1.875 1.729,1.49 false 2.323,1.885 2.323,1.479 false 3.052,1.865 3.052,1.24 false 1.177,1.896 1.375,2.094 0.198,0.198 10 false *1 1.646,1.896 1.854,2.083 0.208,0.188 10 false *2 2.24,1.896 2.469,2.083 0.229,0.188 10 false *3 2.969,1.885 3.177,2.073 0.208,0.188 10 false *4
*1 Front Drive Outboard Joint Shaft Assembly
*2 Front No. 2 Axle Outboard Joint Boot Clamp
*3 Front Axle Outboard Joint Boot
*4 Front Axle Outboard Joint Boot Clamp
V100135

Outboard Joint Side
V100136

Inboard Joint Side


Install new parts onto the front drive outboard joint shaft assembly in the following order:

i.

Front No. 2 axle outboard joint boot clamp


ii.

Front axle outboard joint boot


iii.

Front axle outboard joint boot clamp



c.

Pack the joint portion of the front drive outboard joint shaft assembly and front axle outboard joint boot with grease.

Standard grease capacity:

164 to 184 g (5.78 to 6.48 oz.)



d.

Install the front axle outboard joint boot onto the front drive outboard joint shaft assembly groove.

NOTICE:
·

Do not allow grease to adhere to the boot clamp track of the outboard joint boot.

·

Keep the inside of the outboard joint boot free of foreign matter.




Hide 43447F 5.INSTALL FRONT NO. 2 AXLE OUTBOARD JOINT BOOT CLAMP

a.

Hold the drive shaft in a vise between aluminum plates.

NOTICE:

Do not overtighten the vise.



b.

Install the front No. 2 axle outboard joint boot clamp onto the front axle outboard joint boot.


c.
C164314N03
1.438,0.76 1.052,0.229 1.052,0.229 0.927,0.229 false 0.646,0.146 1.052,0.385 0.406,0.24 10 false SST

Place SST onto the front No. 2 axle outboard joint boot clamp, press it against the boot and slightly tighten SST.

SST
09521-24010  


d.

Tighten SST so that the front No. 2 axle outboard joint boot clamp is pinched.

NOTICE:

Do not overtighten SST.



e.

Remove SST.


f.
C164315N03
1.333,1.24 0.615,1.375 false 0.323,1.302 0.771,1.542 0.448,0.24 10 false SST

Using SST, measure the clearance of the front No. 2 axle outboard joint boot clamp.

SST
09240-00020  

Clearance:

0.5 to 1.5 mm (0.0197 to 0.0591 in.)


If the clearance is outside the specified range, retighten SST.


Hide 43447E 6.INSTALL FRONT AXLE OUTBOARD JOINT BOOT CLAMP

a.

Install the front axle outboard joint boot clamp onto the front axle outboard joint boot.


b.
C223386N03
2.219,1.229 2.698,1.229 false 2.74,1.146 3.208,1.417 0.469,0.271 10 false SST

Place SST onto the front axle outboard joint boot clamp, press it against the boot and slightly tighten SST.

SST
09521-24010  


c.

Tighten SST so that the front axle outboard joint boot clamp is pinched.

NOTICE:

Do not overtighten SST.



d.

Remove SST.


e.
C223387N03
1.677,1.458 2.333,1.458 false 2.375,1.375 2.865,1.656 0.49,0.281 10 false SST

Using SST, measure the clearance of the front axle outboard joint boot clamp.

SST
09240-00020  

Clearance:

0.5 to 1.5 mm (0.0197 to 0.0591 in.)


If the clearance is outside the specified range, retighten SST.


Hide 43474E 7.INSTALL FRONT DRIVE SHAFT DAMPER (w/ 1 Clamp)

a.
C237814N01
1.698,1.75 2.208,2.01 0.51,0.26 10 (A)

Install the front drive shaft damper onto the front drive outboard joint shaft assembly.


b.

Set the dimension as specified below.

Dimension (A):

223.4 to 227.4 mm (8.80 to 8.95 in.)



c.

Hold the drive shaft in a vise between aluminum plates.

NOTICE:

Do not overtighten the vise.



d.

Install a new front drive shaft damper clamp onto the front drive shaft damper.

NOTICE:

Be sure to install the clamp in the correct position.



e.
C197579N03
1.531,1.021 1.219,0.5 1.219,0.5 1.115,0.5 false 0.833,0.417 1.26,0.635 0.427,0.219 10 false SST

Place SST onto the front drive shaft damper clamp, press it against the boot and slightly tighten SST.

SST
09521-24010  


f.

Tighten SST so that the front drive shaft damper clamp is pinched.

NOTICE:

Do not overtighten SST.



g.

Remove SST.


h.
C197580

Using SST, measure the clearance of the front drive shaft damper clamp.

SST
09240-00020  

Clearance:

0.5 to 1.5 mm (0.0197 to 0.0591 in.)


If the clearance is outside the specified range, retighten SST.


Hide 43474E 8.INSTALL FRONT DRIVE SHAFT DAMPER (w/ 2 Clamps)

a.
C315781C01
0.167,1.604 0.167,1.365 false 1.198,1.615 1.198,1.375 false 0.646,1.615 0.646,1.448 false 1.667,0.615 2.125,0.813 0.458,0.198 10 false (A) 0.115,1.625 0.427,1.823 0.313,0.198 10 false *1 1.135,1.625 1.448,1.823 0.313,0.198 10 false *1 0.583,1.625 0.896,1.823 0.313,0.198 10 false *2
*1 Front Drive Shaft Damper Clamp
*2 Front Drive Shaft Damper


Temporarily install the front drive shaft damper and 2 new front drive shaft damper clamps to the front drive outboard joint shaft assembly as shown in the illustration.


b.

Set the dimension as specified below.

Dimension (A):

222.3 to 226.3 mm (8.76 to 8.90 in.)



c.

Install the 2 front drive shaft damper clamps onto the front drive shaft damper.

NOTICE:

Be sure to install the clamps in the correct position.



d.
C292475

Using needle nose pliers, install the 2 front drive shaft damper clamps.


Hide 9.INSTALL FRONT DRIVE INBOARD JOINT ASSEMBLY

a.
C274277C01
0.688,1.875 0.688,1.333 false 1.708,1.854 1.708,1.615 false 2.49,1.896 2.49,1.688 false 2.927,1.896 2.927,1.26 false 0.604,1.896 0.833,2.104 0.229,0.208 10 false *1 1.635,1.875 1.833,2.063 0.198,0.188 10 false *2 2.417,1.917 2.604,2.115 0.188,0.198 10 false *3 2.844,1.896 3.063,2.094 0.219,0.198 10 false *4
*1 Front Axle Inboard Joint Boot Clamp
*2 Front Axle Inboard Joint Boot
*3 Front No. 2 Axle Inboard Joint Boot Clamp
*4 Protective Tape
V100135

Outboard Joint Side
V100136

Inboard Joint Side


Install new parts onto the front drive outboard joint shaft assembly in the following order:

i.

Front axle inboard joint boot clamp


ii.

Front axle inboard joint boot


iii.

Front No. 2 axle inboard joint boot clamp



b.

Hold the drive shaft in a vise between aluminum plates.

NOTICE:

Do not overtighten the vise.



c.

Remove the protective tape.


d.
C067417C02
1.26,1.719 2.125,1.719 2.125,1.719 1.76,1.427 false 2.156,1.625 2.542,1.885 0.385,0.26 10 false *a
*a Matchmark


Align the matchmarks and install the tripod joint onto the front drive outboard joint shaft assembly.


e.

Using a brass bar and a hammer, install the tripod joint to the front drive outboard joint shaft assembly.

NOTICE:
·

Do not tap the rollers.

·

Keep the tripod joint free of foreign matter.




f.
F045046

Using a snap ring expander, install a new shaft snap ring to the front drive outboard joint shaft assembly.


g.

Pack the front drive inboard joint assembly and front axle inboard boot with grease.

Standard grease capacity:

135 to 155 g (4.76 to 5.46 oz.)



h.
F045461C01
1.979,0.656 1.979,0.271 1.979,0.271 1.333,0.271 false 1.646,0.969 1.646,0.271 false 1.146,0.177 1.365,0.417 0.219,0.24 10 false *a
*a Matchmark


Align the matchmarks and install the front drive inboard joint assembly to the front drive outboard joint shaft assembly.


Hide 10.INSTALL FRONT AXLE INBOARD JOINT BOOT

a.

Install the front axle inboard joint boot to the front drive inboard joint assembly.


b.
C240884C01
0.115,1.656 0.969,1.917 0.854,0.26 12 false *B 0.115,0.052 0.74,0.375 0.625,0.323 12 false *A 1.427,1.385 1.698,1.635 0.271,0.25 10 false (A) 1.417,2.938 1.688,3.198 0.271,0.26 10 false (A)
*A LH Side
*B RH Side


Check whether the drive shaft dimensions (A) are within the following specifications.

Dimension (A):
LH Side 581.5 mm (1.90 ft.)
RH Side 914.9 mm (3.00 ft.)



Hide 43448F 11.INSTALL FRONT AXLE INBOARD JOINT BOOT CLAMP

a.

Hold the drive shaft in a vise between aluminum plates.

NOTICE:

Do not overtighten the vise.



b.

Install the front axle inboard joint boot clamp onto the front axle inboard joint boot.


c.
C195759N02
2.146,1.281 2.438,1 2.438,1 2.833,1 false 2.865,0.917 3.323,1.177 0.458,0.26 10 false SST

Place SST onto the front axle inboard joint boot clamp, press it against the boot and slightly tighten SST.

SST
09521-24010  


d.

Tighten SST so that the front axle inboard joint boot clamp is pinched.

NOTICE:

Do not overtighten SST.



e.

Remove SST.


f.
C195760N02
1.531,1.5 2.365,1.5 false 2.406,1.417 2.854,1.667 0.448,0.25 10 false SST

Using SST, measure the clearance of the front axle inboard joint boot clamp.

SST
09240-00020  

Clearance:

0.5 to 1.5 mm (0.0197 to 0.0591 in.)


If the clearance is outside the specified range, retighten SST.


Hide 43448G 12.INSTALL FRONT NO. 2 AXLE INBOARD JOINT BOOT CLAMP

a.

Install the front No. 2 axle inboard joint boot clamp onto the front axle inboard joint boot.


b.
C239401

Using needle nose pliers, install the front No. 2 axle inboard joint boot clamp.

NOTICE:

Be careful not to damage the front axle inboard joint boot.



Hide 43420G 13.INSTALL FRONT DRIVE SHAFT HOLE SNAP RING LH

a.

Install a new front drive shaft hole snap ring LH.

NOTICE:

Face the end gap of the front drive shaft hole snap ring downward.