Home › Suspension › ALIGNMENT / HANDLING DIAGNOSIS › FRONT WHEEL ALIGNMENT › 2012.02–2015.04
RM2040EQ _53 Suspension _014704 ALIGNMENT / HANDLING DIAGNOSIS _0074963 FRONT WHEEL ALIGNMENT N

ALIGNMENT / HANDLING DIAGNOSIS  FRONT WHEEL ALIGNMENT  ADJUSTMENT  


CAUTION / NOTICE / HINT

NOTICE:

If the wheel alignment has been adjusted, or if suspension or underbody components have been removed/installed or replaced, be sure to perform the following initialization procedure in order for the system to function normally:

Perform zero point calibration of the yaw rate and acceleration sensor.



PROCEDURE

Hide 2.MEASURE VEHICLE HEIGHT

C239047N09
1.49,1.281 1.719,1.531 0.229,0.25 10 false D 0.531,4.115 0.76,4.354 0.229,0.24 10 false A 2.063,4.208 2.26,4.427 0.198,0.219 10 false B 2.927,1.229 3.146,1.479 0.219,0.25 10 false C

NOTICE:
·

Before inspecting the wheel alignment, adjust the vehicle height to the specified value.

·

Be sure to perform measurement on a level surface.

·

If it is necessary to go under the vehicle for measurement, confirm that the parking brake is applied and the vehicle is secured with chocks.

·

Make sure to perform the wheel alignment with the vehicle unloaded and the fuel tank fully filled with fuel.

·

The standard value shown here is a value that is used for adjusting the wheel alignment and does not indicate the height of an actual vehicle.



a.

Bounce the vehicle up and down at the corners to stabilize the suspension.


b.

Measure the vehicle height.

Measurement points:

A: Ground clearance of front wheel center


B: Ground clearance of lower No. 2 suspension arm bushing set bolt center


C: Ground clearance of rear wheel center


D: Ground clearance of strut rod set bolt center


Vehicle Height (Unloaded Vehicle):
Front A - B Rear C - D
124.4 mm (4.90 in.) 53.1 mm (2.09 in.)



Hide 3.INSPECT CAMBER, CASTER AND STEERING AXIS INCLINATION

NOTICE:

Inspect while the vehicle is unloaded.


a.
C132440C19
2.385,1.094 2.49,0.813 2.49,0.813 2.719,0.813 false 0.604,0.688 1.031,0.688 1.031,0.688 1.031,1.458 false 2.76,0.719 3.01,0.948 0.25,0.229 10 false *2 0.438,0.604 0.688,0.844 0.25,0.24 10 false *1
*1 Turning Radius Gauge
*2 Camber-caster-kingpin Gauge


Install a camber-caster-kingpin gauge and place the front wheels on the center of a turning radius gauge.


b.

Inspect the camber, caster and steering axis inclination.

Camber (Unloaded Vehicle):
Camber Inclination Right-left Difference
-0.69° +/- 0.75°(-0°41' +/- 45') 0.75°(0°45') or less


Caster (Unloaded Vehicle):
Caster Inclination Right-left Difference
2.93° +/- 0.75°(2°56' +/- 45') 0.75°(0°45') or less


Steering Axis Inclination (Unloaded Vehicle):
Steering Axis Inclination
12.10°(12°06')



Hide 4.ADJUST CAMBER

NOTICE:

Inspect toe-in after the camber has been adjusted.


a.

Remove the front wheel.


b.
C132409

Remove the 2 nuts on the lower side of the front shock absorber assembly.

NOTICE:

Keep the bolts inserted.



c.

Remove the top and bottom bolts one at a time and confirm that the steering knuckle can move freely in the front shock absorber assembly.

HINT:
·

Reinstall each bolt after removing it and confirming steering knuckle movement.

·

If the steering knuckle does not move freely in the front shock absorber assembly, clean the installation surfaces of the front shock absorber assembly and the steering knuckle.




d.

Temporarily install the 2 nuts. (Step A)


e.
C199624N05
1.01,0.125 1.167,0.323 0.156,0.198 10 - 1.875,0.052 2.031,0.25 0.156,0.198 10 +

Fully push or pull the front axle hub in the direction of the required adjustment. (Step B)


f.
C132409

Tighten the nuts.

Torque:
210 N*m (2141 kgf*cm, 154 ft.*lbf)

NOTICE:

Keep the bolts from rotating when tightening the nuts.



g.

Install the front wheel.

Torque:
103 N*m (1049 kgf*cm, 76 ft.*lbf)


h.
C239065N05
1.302,0.479 1.302,0.198 1.302,0.198 1.833,0.198 false 1.323,0.802 1.323,1.073 false 1.865,0.104 2.083,0.333 0.219,0.229 10 false 1 1.292,1.083 1.49,1.313 0.198,0.229 10 false 2

Check the camber.

If the measured value is not within the specification, calculate the required adjustment amount using the formula below.

Camber adjustment amount = center of the specified range - measured value

Check the combination of the installed bolts. Select appropriate bolts from the tables below to adjust the camber to the specified values.

HINT:

Try to adjust the camber to the center of the specified values.


To move the axle hub toward (+) in step B To move the axle hub toward (-) in step B
Refer to table (1) (To move the axle hub toward the positive side) Refer to table (2) (To move the axle hub toward the negative side)

The body and suspension may be damaged if the camber cannot be correctly adjusted according to the tables above.

NOTICE:

Replace the nut with a new one when replacing the bolt.


i.

Table (1) (To move the axle hub toward the positive side)

C212217C12
2.052,0.531 2.188,0.74 0.135,0.208 10 false 1 2.052,1.146 2.188,1.354 0.135,0.208 10 false 2 2.542,0.781 2.719,0.948 0.177,0.167 10 false *c 3.229,1.375 3.417,1.552 0.188,0.177 10 false *d 5.979,0.781 6.125,0.938 0.146,0.156 10 false *e 5.271,0.781 5.469,0.969 0.198,0.188 10 false *d 4.604,1.375 4.781,1.552 0.177,0.177 10 false *f 3.927,1.375 4.104,1.552 0.177,0.177 10 false *e 4.406,6.365 4.552,6.521 0.146,0.156 10 false *f 5.979,1.375 6.188,1.531 0.208,0.156 10 false *f 5.271,1.375 5.469,1.552 0.198,0.177 10 false *f 6.656,1.375 6.833,1.531 0.177,0.156 10 false *f 6.656,0.781 6.823,0.948 0.167,0.167 10 false *f 2.542,2.99 2.677,3.198 0.135,0.208 10 false A 2.542,4.188 2.677,4.396 0.135,0.208 10 false F 2.542,3.469 2.677,3.677 0.135,0.208 10 false C 2.542,3.938 2.677,4.146 0.135,0.208 10 false E 2.542,3.24 2.677,3.448 0.135,0.208 10 false B 2.542,3.708 2.677,3.917 0.135,0.208 10 false D 3.927,3.01 4.063,3.219 0.135,0.208 10 false C 5.271,3 5.406,3.208 0.135,0.208 10 false E 3.229,3.01 3.365,3.219 0.135,0.208 10 false B 4.604,3 4.74,3.208 0.135,0.208 10 false D 3.229,2.76 3.365,2.969 0.135,0.208 10 false G 3.229,3.24 3.365,3.448 0.135,0.208 10 false C 3.229,3.708 3.365,3.917 0.135,0.208 10 false E 3.229,3.469 3.365,3.677 0.135,0.208 10 false D 3.229,3.938 3.375,4.146 0.146,0.208 10 false F 3.927,2.51 4.063,2.719 0.135,0.208 10 false G 3.927,2.76 4.063,2.969 0.135,0.208 10 false A 3.927,3.708 4.063,3.917 0.135,0.208 10 false F 3.927,3.469 4.063,3.677 0.135,0.208 10 false E 3.927,3.24 4.063,3.448 0.135,0.208 10 false D 4.604,2.281 4.74,2.49 0.135,0.208 10 false G 6.656,1.563 6.792,1.771 0.135,0.208 10 false G 5.979,1.813 6.115,2.021 0.135,0.208 10 false G 5.271,2.031 5.406,2.24 0.135,0.208 10 false G 6.656,1.813 6.792,2.021 0.135,0.208 10 false A 6.656,2.281 6.792,2.49 0.135,0.208 10 false C 6.656,2.76 6.792,2.969 0.135,0.208 10 false E 6.656,2.031 6.792,2.24 0.135,0.208 10 false B 6.656,2.51 6.792,2.719 0.135,0.208 10 false D 5.979,2.031 6.115,2.24 0.135,0.208 10 false A 5.979,2.51 6.115,2.719 0.135,0.208 10 false C 5.979,2.281 6.115,2.49 0.135,0.208 10 false B 5.979,2.76 6.115,2.969 0.135,0.208 10 false D 5.979,3 6.115,3.208 0.135,0.208 10 false F 5.271,3.24 5.406,3.448 0.135,0.208 10 false F 5.271,2.281 5.406,2.49 0.135,0.208 10 false A 5.271,2.76 5.406,2.969 0.135,0.208 10 false C 5.271,2.51 5.406,2.719 0.135,0.208 10 false B 4.604,2.51 4.74,2.719 0.135,0.208 10 false A 4.604,2.76 4.74,2.969 0.135,0.208 10 false B 4.604,3.24 4.74,3.448 0.135,0.208 10 false E 4.604,3.469 4.74,3.677 0.135,0.208 10 false F 1.635,5.052 1.771,5.26 0.135,0.208 10 false A 5.094,5.052 5.229,5.26 0.135,0.208 10 false F 3.052,5.052 3.188,5.26 0.135,0.208 10 false C 4.406,5.052 4.542,5.26 0.135,0.208 10 false E 2.344,5.052 2.479,5.26 0.135,0.208 10 false B 3.729,5.052 3.865,5.26 0.135,0.208 10 false D 5.802,5.052 5.938,5.26 0.135,0.208 10 false G 1.073,5.5 1.208,5.708 0.135,0.208 10 false 1 1.104,6.135 1.24,6.344 0.135,0.208 10 false 2 3.052,6.365 3.24,6.521 0.188,0.156 10 false *f 3.729,6.365 3.969,6.531 0.24,0.167 10 false *f 5.094,6.365 5.302,6.563 0.208,0.198 10 false *f 5.094,5.74 5.281,5.896 0.188,0.156 10 false *f 4.406,5.74 4.604,5.896 0.198,0.156 10 false *e 2.344,6.365 2.552,6.531 0.208,0.167 10 false *e 1.635,6.365 1.781,6.521 0.146,0.156 10 false *d 3.729,5.74 3.917,5.927 0.188,0.188 10 false *d 3.052,5.74 3.25,5.927 0.198,0.188 10 false *c 1.635,5.74 1.813,5.927 0.177,0.188 10 false *c 2.344,5.74 2.521,5.896 0.177,0.156 10 false *c 5.802,6.365 5.99,6.531 0.188,0.167 10 false *c 5.802,5.74 6.01,5.927 0.208,0.188 10 false *c 0.177,1.563 2.198,1.75 2.021,0.188 10 false -1°30' to -1°15' (-1.50° to -1.25°) 0.406,2.76 1.969,2.948 1.563,0.188 10 false -0°15' to 0° (-0.25° to 0°) 0.208,2.51 2.156,2.729 1.948,0.219 10 false -0°30' to -0°15' (-0.5° to -0.25°) 0.208,2.281 2.156,2.479 1.948,0.198 10 false -0°45' to -0°30' (-0.75° to -0.5°) 0.271,2.031 2.104,2.208 1.833,0.177 10 false -1°00' to -0°45' (-1° to -0.75°) 0.26,1.813 2.094,2.021 1.833,0.208 10 false -1°15' to -1°00' (-1.25° to -1°) 0.354,3.938 2.01,4.115 1.656,0.177 10 false 1°00' to 1°15' (1° to 1.25°) 0.354,3.708 2,3.906 1.646,0.198 10 false 0°45' to 1°00' (0.75° to 1°) 0.302,3.469 2.073,3.646 1.771,0.177 10 false 0°30' to 0°45' (0.5° to 0.75°) 0.302,3.24 2.073,3.417 1.771,0.177 10 false 0°15' to 0°30' (0.25° to 0.5°) 0.448,3 1.917,3.198 1.469,0.198 10 false 0° to 0°15' (0° to 0.25°) 0.302,4.188 2.073,4.365 1.771,0.177 10 false 1°15' to 1°30' (1.25° to 1.5°) 2.542,1.375 2.719,1.552 0.177,0.177 10 false *c 3.229,0.781 3.406,0.938 0.177,0.156 10 false *c 3.927,0.792 4.115,0.979 0.188,0.188 10 false *c 4.604,0.781 4.781,0.948 0.177,0.167 10 false *c 5.979,3 6.115,3.208 0.135,0.208 10 false F 1.156,0.625 1.333,0.792 0.177,0.167 10 false *a 0.625,1.115 0.802,1.281 0.177,0.167 10 false *b 0.875,4.792 1.052,4.958 0.177,0.167 10 false *B 0.063,0.135 0.26,0.302 0.198,0.167 10 false *A
*A Table (1) (To move the axle hub toward the positive side) *B Selected Bolt Combination
*a Installed Bolt *b Adjusting Value
*c 90105-17012 *d 90105-17013
*e 90105-17014 *f 90105-17015



ii.

Table (2) (To move the axle hub toward the negative side)

C212218C12
2.052,0.531 2.188,0.74 0.135,0.208 10 false 1 2.052,1.146 2.188,1.354 0.135,0.208 10 false 2 1.635,5.052 1.771,5.26 0.135,0.208 10 false A 5.094,5.052 5.229,5.26 0.135,0.208 10 false F 3.052,5.052 3.188,5.26 0.135,0.208 10 false C 4.406,5.052 4.542,5.26 0.135,0.208 10 false E 2.344,5.052 2.479,5.26 0.135,0.208 10 false B 3.729,5.052 3.865,5.26 0.135,0.208 10 false D 5.802,5.052 5.938,5.26 0.135,0.208 10 false G 1.073,5.5 1.208,5.708 0.135,0.208 10 false 1 1.104,6.135 1.24,6.344 0.135,0.208 10 false 2 0.177,1.563 2.198,1.75 2.021,0.188 10 false -1°30' to -1°15' (-1.50° to -1.25°) 0.406,2.76 1.969,2.948 1.563,0.188 10 false -0°15' to 0° (-0.25° to 0°) 0.208,2.521 2.156,2.74 1.948,0.219 10 false -0°30' to -0°15' (-0.5° to -0.25°) 0.208,2.281 2.156,2.479 1.948,0.198 10 false -0°45' to -0°30' (-0.75° to -0.5°) 0.271,2.031 2.104,2.208 1.833,0.177 10 false -1°00' to -0°45' (-1° to -0.75°) 0.26,1.813 2.094,2.021 1.833,0.208 10 false -1°15' to -1°00' (-1.25° to -1°) 0.354,3.938 2.01,4.115 1.656,0.177 10 false 1°00' to 1°15' (1° to 1.25°) 0.354,3.708 2,3.906 1.646,0.198 10 false 0°45' to 1°00' (0.75° to 1°) 0.302,3.469 2.073,3.646 1.771,0.177 10 false 0°30' to 0°45' (0.5° to 0.75°) 0.302,3.24 2.073,3.417 1.771,0.177 10 false 0°15' to 0°30' (0.25° to 0.5°) 0.448,3 1.917,3.198 1.469,0.198 10 false 0° to 0°15' (0° to 0.25°) 0.302,4.188 2.073,4.365 1.771,0.177 10 false 1°15' to 1°30' (1.25° to 1.5°) 1.156,0.625 1.333,0.792 0.177,0.167 10 false *a 0.625,1.115 0.802,1.281 0.177,0.167 10 false *b 0.875,4.792 1.052,4.958 0.177,0.167 10 false *B 0.063,0.135 0.26,0.302 0.198,0.167 10 false *A 5.292,2.76 5.427,2.969 0.135,0.208 10 false E 5.292,3.708 5.427,3.917 0.135,0.208 10 false G 5.292,2.521 5.427,2.729 0.135,0.208 10 false F 5.292,3.469 5.427,3.677 0.135,0.208 10 false A 5.292,3 5.427,3.208 0.135,0.208 10 false C 5.292,3.24 5.427,3.448 0.135,0.208 10 false B 2.542,2.76 2.677,2.969 0.135,0.208 10 false A 2.542,1.563 2.677,1.771 0.135,0.208 10 false F 2.542,2.281 2.677,2.49 0.135,0.208 10 false C 2.542,1.813 2.677,2.021 0.135,0.208 10 false E 2.542,2.521 2.677,2.729 0.135,0.208 10 false B 2.542,2.031 2.677,2.24 0.135,0.208 10 false D 3.229,2.76 3.365,2.969 0.135,0.208 10 false B 3.229,3 3.365,3.208 0.135,0.208 10 false G 3.229,2.521 3.365,2.729 0.135,0.208 10 false C 3.229,2.031 3.365,2.24 0.135,0.208 10 false E 3.229,2.281 3.365,2.49 0.135,0.208 10 false D 3.229,1.813 3.375,2.021 0.146,0.208 10 false F 3.927,2.76 4.063,2.969 0.135,0.208 10 false C 3.927,3.24 4.063,3.448 0.135,0.208 10 false G 3.927,3 4.063,3.208 0.135,0.208 10 false A 3.927,2.063 4.063,2.271 0.135,0.208 10 false F 3.927,2.281 4.063,2.49 0.135,0.208 10 false E 3.927,2.521 4.063,2.729 0.135,0.208 10 false D 4.604,2.76 4.74,2.969 0.135,0.208 10 false D 4.604,3.469 4.74,3.677 0.135,0.208 10 false G 4.604,3.24 4.74,3.448 0.135,0.208 10 false A 4.604,3 4.74,3.208 0.135,0.208 10 false B 4.604,2.521 4.74,2.729 0.135,0.208 10 false E 4.604,2.281 4.74,2.49 0.135,0.208 10 false F 5.99,3.938 6.125,4.146 0.135,0.208 10 false G 5.99,3.708 6.125,3.917 0.135,0.208 10 false A 5.99,3.24 6.125,3.448 0.135,0.208 10 false C 5.99,3.469 6.125,3.677 0.135,0.208 10 false B 5.99,3 6.125,3.208 0.135,0.208 10 false D 5.99,2.76 6.125,2.969 0.135,0.208 10 false F 6.688,4.188 6.823,4.396 0.135,0.208 10 false G 6.688,3.938 6.823,4.146 0.135,0.208 10 false A 6.688,3.469 6.823,3.677 0.135,0.208 10 false C 6.688,3 6.823,3.208 0.135,0.208 10 false E 6.688,3.708 6.823,3.917 0.135,0.208 10 false B 6.688,3.24 6.823,3.448 0.135,0.208 10 false D 2.542,0.781 2.719,0.948 0.177,0.167 10 false *c 3.229,1.365 3.417,1.542 0.188,0.177 10 false *d 5.979,0.771 6.125,0.927 0.146,0.156 10 false *e 5.271,0.781 5.469,0.969 0.198,0.188 10 false *d 4.604,1.375 4.781,1.552 0.177,0.177 10 false *f 3.927,1.375 4.104,1.552 0.177,0.177 10 false *e 5.979,1.375 6.188,1.531 0.208,0.156 10 false *f 5.271,1.375 5.469,1.552 0.198,0.177 10 false *f 6.656,1.375 6.833,1.531 0.177,0.156 10 false *f 6.656,0.781 6.823,0.948 0.167,0.167 10 false *f 2.542,1.375 2.719,1.552 0.177,0.177 10 false *c 3.229,0.781 3.406,0.938 0.177,0.156 10 false *c 3.927,0.792 4.115,0.979 0.188,0.188 10 false *c 4.604,0.781 4.781,0.948 0.177,0.167 10 false *c 4.406,6.365 4.552,6.521 0.146,0.156 10 false *f 3.052,6.365 3.24,6.521 0.188,0.156 10 false *f 3.729,6.365 3.969,6.531 0.24,0.167 10 false *f 5.094,6.365 5.302,6.563 0.208,0.198 10 false *f 5.094,5.74 5.281,5.896 0.188,0.156 10 false *f 4.406,5.74 4.604,5.896 0.198,0.156 10 false *e 2.344,6.354 2.552,6.521 0.208,0.167 10 false *e 1.635,6.354 1.781,6.51 0.146,0.156 10 false *d 3.729,5.75 3.917,5.938 0.188,0.188 10 false *d 3.052,5.74 3.25,5.927 0.198,0.188 10 false *c 1.635,5.729 1.813,5.917 0.177,0.188 10 false *c 2.344,5.74 2.521,5.896 0.177,0.156 10 false *c 5.802,6.365 5.99,6.531 0.188,0.167 10 false *c 5.802,5.74 6.01,5.927 0.208,0.188 10 false *c
*A Table (2) (To move the axle hub toward the negative side) *B Selected Bolt Combination
*a Installed Bolt *b Adjusting Value
*c 90105-17012 *d 90105-17013
*e 90105-17014 *f 90105-17015




i.

If the camber was out of adjustment in the previous step, perform the adjust camber steps mentioned above. In step (A), replace the existing bolts with the selected bolts.

HINT:

Replace one bolt at a time when replacing both bolts.



Hide 5.INSPECT TOE-IN

NOTICE:

Inspect while the vehicle is unloaded.


a.

Bounce the vehicle up and down at the corners to stabilize the suspension.


b.

Release the parking brake and move the shift lever to N.


c.

Push the vehicle straight ahead approximately 5 m (16.4 ft.). (Step C)


d.
C188968C17
0.823,0.552 0.823,1.083 false 1.375,0.552 1.375,0.958 1.375,0.958 0.823,0.958 false 2.521,1.344 2.521,1.677 false 0.74,1.094 0.979,1.313 0.24,0.219 10 false *a 2.438,1.698 2.646,1.906 0.208,0.208 10 false *b
*a Tread Center Mark
*b Dimension B
V100135

Front of the Vehicle


Put tread center marks on the rearmost points of the front wheels and measure the distance between the marks (dimension B).


e.

Slowly push the vehicle straight ahead to cause the front wheels to rotate 180°. Use the front tire valve as a reference point.

HINT:

Do not allow the wheels to rotate more than 180°. If the wheels rotate more than 180°, perform the procedure from Step C again.



f.
C188969C15
0.646,1.281 0.646,1.646 false 1.927,0.542 2.135,0.771 0.208,0.229 10 false C 3.063,0.552 3.271,0.76 0.208,0.208 10 false D 2.5,0.719 2.708,0.948 0.208,0.229 10 false A 2.51,1.531 2.719,1.771 0.208,0.24 10 false B 0.563,1.646 0.781,1.885 0.219,0.24 10 false *a
*a Dimension A
V100135

Front of the Vehicle


Measure the distance between the tread center marks on the front of the wheels (dimension A).

Toe-in (Unloaded Vehicle):
Specified Condition
C + D: 0.02° +/- 0.17°(0°01' +/- 0°10')
B - A: 0.26 +/- 2.0 mm (0.0102 +/- 0.0787 in.)


HINT:

Measure "B - A" only when "C + D" cannot be measured.


If the toe-in is not within the specified range, adjust it at the rack ends.


Hide 6.ADJUST TOE-IN

a.
C239071C08
2.625,1.219 2.865,1.458 0.24,0.24 10 false *a
*a Thread Length


Make sure that the thread length of the right and left rack ends are approximately the same.

Standard difference:

1.5 mm (0.0591 in.) or less



b.

Remove the steering rack boot clips.


c.
C239070

Loosen the tie rod end lock nuts.


d.

Adjust the rack ends if the difference in thread length between the right and left rack ends is not within the specified range.

i.

If the toe-in measurement is greater than the specified range (too much toe-out), extend the shorter rack end so that the length difference is within the specified range.


ii.

If the toe-in measurement is less than the specified range (too much toe-in), shorten the longer rack end so that the length difference is within the specified range.


iii.

Measure the toe-in.



e.

Turn the right and left rack ends by an equal amount to adjust the toe-in.


f.

Make sure that the thread lengths of the right and left rack ends are the same.


g.

Tighten the tie rod end lock nuts.

Torque:
74 N*m (755 kgf*cm, 55 ft.*lbf)


h.

Place the steering rack boots on the seats and install the steering rack boot clips.

HINT:

Make sure that the steering rack boots are not twisted.



Hide 7.INSPECT WHEEL ANGLE

a.
C132439C13
0.875,0.219 1.094,0.427 0.219,0.208 10 false *b 0.542,0.208 0.771,0.438 0.229,0.229 10 false *a 2.375,0.219 2.635,0.438 0.26,0.219 10 false *b 2.729,0.208 2.969,0.438 0.24,0.229 10 false *a
*a Inside
*b Outside
V100135

Front of the Vehicle


Put tread center marks on the rearmost points of a turning radius gauge.


b.

Turn the steering wheel fully to the left and right and measure the turning angle.

NOTICE:

Inspect while the vehicle is unloaded.


Wheel Turning Angle (Unloaded Vehicle):
Inside Wheel Outside Wheel Reference
38.60° +/- 2°(38°36' +/- 2°) 33.75°(33°45')


If the right and left inside wheel angles differ from the specified value, check and adjust the right and left rack end lengths.



Hide 8. PLACE FRONT WHEELS FACING STRAIGHT AHEAD

Hide 9. PERFORM YAW RATE AND ACCELERATION SENSOR CALIBRATION