Home › Suspension › REAR SUSPENSION › REAR SHOCK ABSORBER
RM2040EQ _53 Suspension _014706 REAR SUSPENSION _0074972 REAR SHOCK ABSORBER A

REAR SUSPENSION  REAR SHOCK ABSORBER  REMOVAL  


CAUTION / NOTICE / HINT

HINT:
·

Use the same procedure for the RH side and LH side.

·

The procedure listed below is for the LH side.



PROCEDURE

Hide 1.REMOVE REAR SIDE SEATBACK ASSEMBLY

Hide 2.REMOVE REAR WHEEL

Hide 48840A 3.SEPARATE REAR STABILIZER LINK ASSEMBLY

a.
C239069

Remove the nut and separate the rear stabilizer link assembly from the rear shock absorber assembly.

If the ball joint turns together with the nut, use a hexagon wrench to hold the stud.


Hide 47319F 4.SEPARATE REAR FLEXIBLE HOSE

a.
C246317

Remove the bolt and separate the rear flexible hose from the rear shock absorber assembly.


Hide 89516D 5.SEPARATE SKID CONTROL SENSOR WIRE

a.
C246983

Remove the bolt and separate the skid control sensor wire from the rear shock absorber assembly.


Hide 48753C 6.REMOVE REAR NO. 1 SUSPENSION SUPPORT COVER

a.
C132462

Using a screwdriver, disengage the 4 claws and remove the rear No. 1 suspension support cover.


Hide 7.REMOVE REAR SHOCK ABSORBER WITH COIL SPRING

a.
C241287
1.208,2.073 1.208,1.802 1.208,1.802 0.938,1.802 false 2.25,1.656 2.708,1.656 false 2.281,4.063 2.281,4.417 false 0.771,1.719 1.01,1.938 0.24,0.219 10 false *1 2.75,1.573 3,1.813 0.25,0.24 10 false *2 2.198,4.438 2.417,4.635 0.219,0.198 10 false *2
*1 Jack
*2 Wooden Block


Support the rear axle carrier sub-assembly with a jack using a wooden block.

HINT:

Support the rear axle carrier sub-assembly until reinstallation of the rear shock absorber with coil spring is complete.



b.
C132463

Loosen the rear support to rear shock absorber nut of the rear shock absorber assembly.

NOTICE:
·

Do not remove the rear support to rear shock absorber nut.

·

Loosen the nut only when the rear shock absorber with coil spring needs to be disassembled.




c.
C132464

Remove the 2 bolts and 2 nuts, and separate the rear shock absorber with coil spring from the rear axle carrier sub-assembly.

NOTICE:

When removing the nuts, keep the bolts from rotating.



d.
C132465

Remove the 3 nuts and rear shock absorber with coil spring.

NOTICE:

Make sure that the skid control sensor wire and rear flexible hose are disconnected from the rear shock absorber with coil spring.



Hide 48760C 8.REMOVE REAR SUPPORT TO REAR SHOCK ABSORBER NUT

a.
C265186
2.344,1.104 2.667,1.104 false 2.729,1.042 3.188,1.24 0.458,0.198 10 SST

Secure SST in a vise.

SST
09727-30021  (09727-00010, 09727-00021, 09727-00031)


b.
C275706C11
0.323,0.167 0.635,0.479 0.313,0.313 10 false *a 0.354,2.479 0.698,2.792 0.344,0.313 10 false *b
*a Correct
*b Incorrect


Attach the arms of SST to the diameter of the rear coil spring.

CAUTION:
·

Make sure that the rear coil spring is installed so that the distance between the upper and lower arms of SST is at the maximum.

·

Make sure that the claws of the arms are securely attached.




c.

Using SST, compress the rear coil spring.

CAUTION:
·

If the rear coil spring bends during compression, immediately stop compression and reinstall SST.

·

Do not excessively compress the rear coil spring so that the coils contact each other.

·

Do not use an impact wrench. It will damage SST.




d.

Confirm that the rear coil spring becomes free and remove the rear support to rear shock absorber nut.

CAUTION:

Do not remove the rear support to rear shock absorber nut when the rear coil spring is not free.



Hide 48760D 9.REMOVE REAR SUPPORT TO REAR SHOCK ABSORBER COLLAR

Hide 48760B 10.REMOVE REAR SUSPENSION SUPPORT ASSEMBLY

Hide 48231B 11.REMOVE REAR COIL SPRING

Hide 48341B 12.REMOVE REAR NO. 1 SPRING BUMPER

Hide 48258C 13.REMOVE REAR LOWER COIL SPRING INSULATOR

Hide 48540 14.REMOVE REAR SHOCK ABSORBER ASSEMBLY