Home › Steering › POWER ASSIST SYSTEMS › POWER STEERING SYSTEM
RM2040EQ _55 Steering _014713 POWER ASSIST SYSTEMS _0074999 POWER STEERING SYSTEM U

POWER ASSIST SYSTEMS  POWER STEERING SYSTEM  TERMINALS OF ECU  


CHECK POWER STEERING ECU ASSEMBLY


C239855
3.729,0.198 4.052,0.396 0.323,0.198 5.719,0.198 6.042,0.396 0.323,0.198 3.906,1.844 4.229,2.042 0.323,0.198 4.708,1.844 5.031,2.042 0.323,0.198 5.563,1.844 5.885,2.042 0.323,0.198 1.875,0.833 2.198,1.031 0.323,0.198 0.719,1.313 1.042,1.51 0.323,0.198 1.104,1.313 1.427,1.51 0.323,0.198 1.479,1.313 1.802,1.51 0.323,0.198 0.688,3.469 1.01,3.667 0.323,0.198 0.906,1.313 1.031,1.146 false 1.271,1.313 1.292,1.146 false 1.625,1.313 1.542,1.146 false 2.021,0.833 2.021,0.771 false 1.01,3.521 1.083,3.49 false 3.854,0.198 4.146,0.521 0.292,0.323 10 false j2 5.844,0.188 6.094,0.333 0.25,0.146 10 false c 4.021,1.854 4.219,2.146 0.198,0.292 10 false j3 4.833,1.844 5.01,1.99 0.177,0.146 10 false a 5.688,1.854 5.865,2 0.177,0.146 10 false b 0.146,0.083 0.427,0.313 0.281,0.229 10 false *a 1.99,0.833 2.24,1.219 0.25,0.385 10 false j2 0.833,1.313 1.01,1.552 0.177,0.24 10 false j3 1.229,1.313 1.406,1.458 0.177,0.146 10 false a 1.625,1.323 1.802,1.469 0.177,0.146 10 false b 0.813,3.479 1.063,3.625 0.25,0.146 10 false c
*a Component without harness connected
(Power Steering ECU Assembly)
- -


a.

Measure the voltage and resistance according to the value(s) in the table below.

NOTICE:

When the EPS warning light is illuminated due to a malfunction, the fail-safe function may cause the voltage of the power steering ECU assembly terminals to become 0 V.


Terminal No. (Symbol) Wiring Color Terminal Description Condition Specified Condition
j3-1 (IG) - j2-2 (PGND) R - B IG power source Power switch on (IG) 9 to 16 V
j3-4 (CANH) - j3-8 (CANL) Y - SB CAN communication line Power switch off 54 to 69 Ω
j3-5 (TS) - j2-2 (PGND) O - B Terminal TS of DLC3 Always 9 to 16 V
a-1 (TRQG) - Body ground B - Body ground Torque sensor ground Always Below 1 Ω
a-2 (TRQ2) - a-1 (TRQG) Y - B Torque sensor signal
Power switch on (READY)
Power switch on (READY)
Steering wheel not being turned (without load)
2.3 to 2.7 V
Power switch on (READY)
Steering wheel being turned to right with vehicle stopped
0.3 to 2.5 V
Power switch on (READY)
Steering wheel being turned to left with vehicle stopped
2.5 to 4.7 V
a-3 (TRQV) - a-1 (TRQG) R - B Torque sensor voltage source Power switch on (IG) 8.5 to 10.5 V
a-5 (TRQF) - j2-2 (PGND) G - B Torque sensor reference voltage Power switch on (IG) 3.35 to 3.37 V
a-7 (TRQ1) - a-1 (TRQG) W - B Torque sensor signal Power switch on (READY)
Steering wheel not being turned (without load)
2.3 to 2.7 V
Power switch on (READY)
Steering wheel being turned to right with vehicle stopped
2.5 to 4.7 V
Power switch on (READY)
Steering wheel being turned to left with vehicle stopped
0.3 to 2.5 V
b-1 (RZCS2) - j2-2 (PGND) B - B Rotation angle sensor COS aspect output signal Power switch on (READY)
Steering wheel turned
0.68 to 4.42 V
b-2 (RZV2) - j2-2 (PGND) G - B Rotation angle sensor excitation output signal Power switch on (READY)
Steering wheel turned
0.68 to 4.42 V
b-3 (RZSN2) - j2-2 (PGND) L - B Rotation angle sensor SIN aspect output signal Power switch on (READY)
Steering wheel turned
0.68 to 4.42 V
b-5 (RZCS1) - j2-2 (PGND) R - B Rotation angle sensor COS aspect output signal Power switch on (READY)
Steering wheel turned
0.68 to 4.42 V
b-6 (RZV1) - j2-2 (PGND) W - B Rotation angle sensor excitation output signal Power switch on (READY)
Steering wheel turned
0.68 to 4.42 V
b-7 (RZSN1) - j2-2 (PGND) Y - B Rotation angle sensor SIN aspect output signal Power switch on (READY)
Steering wheel turned
0.68 to 4.42 V
j2-1 (PIG) - j2-2 (PGND) R - B Power source Always 9 to 16 V
j2-2 (PGND) - Body ground B - Body ground Power ground Always Below 1 Ω
c-1 (PHA) - j2-2 (PGND) # - B A phase motor output Power switch on (READY)
Steering wheel turned
Value changes within 4 to 35 V range
c-2 (PHB) - j2-2 (PGND) # - B B phase motor output Power switch on (READY)
Steering wheel turned
Value changes within 4 to 35 V range
c-3 (PHC) - j2-2 (PGND) # - B C phase motor output Power switch on (READY)
Steering wheel turned
Value changes within 4 to 35 V range

HINT:

# means that the motor terminal is tightened directly to the ECU with bolts.