Home › Steering › POWER ASSIST SYSTEMS › POWER STEERING SYSTEM
RM2040EQ _55 Steering _014713 POWER ASSIST SYSTEMS _0074999 POWER STEERING SYSTEM J

POWER ASSIST SYSTEMS  POWER STEERING SYSTEM  TS and CG Terminal Circuit  


DESCRIPTION

In Test Mode (signal check), a malfunction in a speed sensor that cannot be detected when the vehicle is stopped can be detected while driving.

Sensor check mode can be entered by connecting terminals TS and CG of the DLC3 and turning the power switch from off to on (IG).

WIRING DIAGRAM

C167369
0.457,2.93 0.674,3.088 0.218,0.158 10 I39 0.94,1.791 1.195,1.954 0.256,0.162 10 CG 0.954,0.909 1.209,1.071 0.256,0.162 10 TS 1.237,0.815 1.435,0.971 0.198,0.156 10 12 1.259,1.694 1.456,1.85 0.198,0.156 10 4 5.727,2.924 5.899,3.073 0.172,0.149 10 j3 6.029,0.906 6.23,1.056 0.201,0.149 10 TS 5.829,0.808 6.003,0.958 0.174,0.149 10 5 5.92,2.924 6.897,3.267 0.977,0.343 10 Power Steering ECU Assembly 0.73,2.93 1.116,3.088 0.387,0.158 10 DLC3

CAUTION / NOTICE / HINT

NOTICE:

If the power steering ECU assembly has been replaced, perform assist map writing.

Click hereSteering>POWER ASSIST SYSTEMS>POWER STEERING SYSTEM>CALIBRATION


PROCEDURE

1.CHECK HARNESS AND CONNECTOR (POWER STEERING ECU ASSEMBLY - TS of DLC3)
a.

Disconnect the power steering ECU assembly j3 connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
j3-5 (TS) - I39-12 (TS) Always Below 1 Ω
j3-5 (TS) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

2.CHECK HARNESS AND CONNECTOR (CG of DLC3 - BODY GROUND)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

2.CHECK HARNESS AND CONNECTOR (CG of DLC3 - BODY GROUND)
a.
C207407C47
1.51,0.865 1.917,1.115 0.406,0.25 1.188,1.406 1.583,1.885 false 0.177,0.177 0.75,0.594 0.573,0.417 10 *a 1.063,1.219 1.406,1.458 0.344,0.24 10 CG 1.604,0.906 2.01,1.281 0.406,0.375 10 I39
*a Front view of DLC3


Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
I39-4(CG) - Body ground Always Below 1 Ω


HINT:

If troubleshooting has been carried out according to Problem Symptoms Table, refer back to the table and proceed to the next step before replacing the part.

Click hereSteering>POWER ASSIST SYSTEMS>POWER STEERING SYSTEM>PROBLEM SYMPTOMS TABLE



Result:
Proceed to
OK
NG



OK

REPLACE POWER STEERING ECU ASSEMBLY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR