Home › Steering › STEERING COLUMN › STEERING COLUMN ASSEMBLY
RM2040EQ _55 Steering _014714 STEERING COLUMN _0075002 STEERING COLUMN ASSEMBLY A

STEERING COLUMN  STEERING COLUMN ASSEMBLY  REASSEMBLY  


CAUTION / NOTICE / HINT

NOTICE:
·

When using a vise, do not overtighten it.

·

Do not drop the power steering ECU with motor assembly, strike it with tools or subject it to impacts.

·

If the power steering ECU with motor assembly is subjected to an impact, replace it with a new one.

·

Do not pull the wire harness of the electric power steering column sub-assembly.

·

Do not allow any moisture to come into contact with the power steering ECU with motor assembly.

·

Do not loosen any bolts not mentioned in the procedure.



PROCEDURE

Hide 89650 1.INSTALL POWER STEERING ECU ASSEMBLY

Hide 2.INSTALL POWER STEERING ECU WITH MOTOR ASSEMBLY

a.
C220801
1.563,1.281 1.563,1.635 1.563,1.635 1.115,1.635 false 1.458,1.313 1.458,1.635 false 0.969,1.552 1.208,1.771 0.24,0.219 10 false *1
*1 Service Nut


Install the 2 service nuts to the steering main shaft.

Recommended service nut:
Thread diameter:

12.0 mm (0.472 in.)

Thread pitch:

1.25 mm (0.0492 in.)



b.

Simultaneously to rotate the service nut that was installed first counterclockwise and rotate the service nut that was installed second clockwise to lock them.

NOTICE:

Do not apply excess torque to the service nuts by using a tool such as an impact wrench.


HINT:

These nuts are installed to turn the steering main shaft. They should be removed after inspecting the steering main shaft rotating torque.



c.

Install a new O-ring to the power steering ECU with motor assembly.


d.
C239327

Apply grease to the splines of the power steering ECU with motor assembly.

NOTICE:

First wipe off the existing grease from the splines, and then apply the dedicated grease supplied with a new power steering motor assembly or electric power steering column sub-assembly.



e.

Insert the power steering ECU with motor assembly into the splines of the electric power steering column sub-assembly.

NOTICE:

Do not damage the gears.



f.
C243097
0.979,1.135 0.979,0.823 0.979,0.823 0.635,0.823 false 2.375,1.615 2.635,1.615 false 0.49,0.74 0.771,1 0.281,0.26 10 false *1 2.656,1.521 2.896,1.74 0.24,0.219 10 false *2
*1 Aluminum Plate
*2 Wooden Block


Secure the steering column assembly in a vice using aluminum plates and wooden block as shown in the illustration.

NOTICE:
·

Do not overtighten the vice, as the steering column assembly may become deformed.

·

Secure the steering column assembly so that power steering motor assembly is directly upright.

·

Support the steering column assembly with a wooden block or similar item to ensure that it does not fall.




g.
C243101

Temporarily install the power steering ECU with motor assembly to the electric power steering column sub-assembly with 2 new bolts while rotating the steering main shaft at approximately 4 rpm.

NOTICE:

When temporarily installing the 2 bolts to the power steering motor assembly, do not tighten them all the way down.



h.

Rotate the steering main shaft 120 to 240 degrees at approximately 4 rpm.


i.

Rotate the steering main shaft 180 degrees clockwise and counterclockwise at approximately 4 rpm and repeat this operation 2 or 3 times to align the power steering ECU with motor assembly.


j.

Tighten the 2 bolts.

Torque:
19 N*m (194 kgf*cm, 14 ft.*lbf)

NOTICE:

Make sure not to move the power steering motor assembly after adjusting the axis.



k.
C243100

Measure the turning torque of the steering main shaft.

Torque:
Turning torque : 1.2 to 1.7 N*m (12 to 17 kgf*cm, 10 to 15 in.*lbf)

NOTICE:

Ensure that there is no abnormal resistance during rotation.


If the torque is not as specified, readjust the axis of the power steering ECU with motor assembly.


l.

Remove the 2 service nuts from the steering main shaft.


m.

Connect the 2 connectors to the power steering ECU assembly.


Hide F1901 3.INSTALL ECU WIRE SUB-ASSEMBLY

a.

Engage the 2 wire harness clamps to install a new ECU wire sub-assembly.


b.

Connect the 2 connectors to the power steering ECU with motor assembly.


Hide 8965A 4.INSTALL POWER STEERING ECU PROTECTOR

a.

Engage the 2 claws to install a new power steering ECU protector to the power steering ECU with motor assembly.


Hide 45020A 5.INSTALL STEERING LOCK ACTUATOR ASSEMBLY

HINT:

When replacing the steering lock actuator assembly, refer to Service Bulletin.


a.

Secure the steering column assembly in a vise.


b.
C243102

Temporarily install the steering lock actuator assembly to the steering column assembly with 2 new tapered-head bolts.


c.

Tighten the 2 tapered-head bolts until the bolt heads break off.