Home › Steering › STEERING COLUMN › STEERING PAD SWITCH › 2012.02–2015.04
RM2040EQ _55 Steering _014714 STEERING COLUMN _0075004 STEERING PAD SWITCH G

STEERING COLUMN  STEERING PAD SWITCH  INSPECTION  


PROCEDURE

Hide 84250A 1.INSPECT STEERING PAD SWITCH ASSEMBLY

a.

Measure the resistance according to the value(s) in the table below.

E245203
3.51,0.833 3.219,1.115 false 3.406,0.833 3.115,0.979 false 3.615,0.833 3.906,1.115 false 3.719,0.833 4.01,0.979 false 1.854,2.615 1.427,2.615 false 2.323,2.604 2.948,2.323 false 2.135,2.615 2.948,2.979 false 5.24,2.615 5.719,2.615 false 2.094,2.375 2.094,1.75 false 1.896,2.219 1.698,1.792 false 2.219,2.198 2.385,1.771 false 5.083,2.406 5.5,2.073 false 5.031,2.844 5.302,3.427 false 2.083,2.844 2.083,3.469 false 1.99,3.031 1.719,3.458 false 2.385,3.115 2.479,3.438 false 3.292,0.698 3.063,0.698 false 3.396,0.688 3.104,0.396 false 3.531,0.688 3.708,0.281 false 5.021,2.177 5.25,1.719 false 2.938,1.365 2.552,1.365 false 0.135,0.115 0.344,0.271 0.208,0.156 10 false *a 1.583,1.635 1.813,1.854 0.229,0.219 10 false *b 2.031,1.583 2.25,1.792 0.219,0.208 10 false *f 1.281,2.521 1.542,2.75 0.26,0.229 10 false *h 2.813,0.927 3.25,1.125 0.438,0.198 10 false EAU 2.833,0.292 3.281,0.531 0.448,0.24 10 false +DP 3.688,0.135 4.083,0.365 0.396,0.229 10 false -DP 2.833,0.615 3.208,0.833 0.375,0.219 10 false HO 2.958,1.104 3.375,1.313 0.417,0.208 10 false AU3 4.031,0.917 4.469,1.146 0.438,0.229 10 false AU1 3.906,1.094 4.313,1.365 0.406,0.271 10 false AU2 2.979,2.24 3.229,2.469 0.25,0.229 10 false *i 2.979,2.906 3.198,3.156 0.219,0.25 10 false *j 5.74,2.521 6.323,2.792 0.583,0.271 10 false *m (*A) 2.354,1.615 2.604,1.844 0.25,0.229 10 false *d 2.406,1.26 2.563,1.417 0.156,0.156 10 false *o 5.5,1.969 5.76,2.208 0.26,0.24 10 false *k 5.219,1.573 5.51,1.854 0.292,0.281 10 false *n 5.292,3.427 5.542,3.677 0.25,0.25 10 false *l 1.604,3.438 1.865,3.656 0.26,0.219 10 false *c 2,3.448 2.26,3.698 0.26,0.25 10 false *g 2.406,3.427 2.646,3.667 0.24,0.24 10 false *e
*A w/ Voice Switch of Steering Pad Switch Assembly - -
*a Component without harness connected
(Steering Pad Switch Assembly)
*b Volume+
*c Volume- *d Back
*e MODE/HOLD *f Up
*g Down *h Left
*i Right *j Enter
*k Off hook *l On hook
*m Voice *n DISP
*o Terminal-A - -


Standard Resistance:
Tester Connection Condition Specified Condition
1 (HO) - Terminal-A Always Below 1 Ω
2 (+DP) - 3 (-DP) No switch pushed 10 kΩ or higher
DISP switch pushed Below 1 Ω
11 (AU1) - 8 (EAU) No switch pushed 95 to 105 kΩ
Up switch pushed Below 2.5 Ω
Down switch pushed 313 to 345 Ω
Volume+ switch pushed 950 to 1050 Ω
Volume- switch pushed 2955 to 3265 Ω
10 (AU2) - 8 (EAU) No switch pushed 95 to 105 kΩ
MODE/HOLD switch pushed Below 2.5 Ω
On hook switch pushed 313 to 345 Ω
Off hook switch pushed 950 to 1050 Ω
Voice switch pushed*1 2955 to 3265 Ω
9 (AU3) - 8 (EAU) No switch pushed 95 to 105 kΩ
Enter switch pushed Below 2.5 Ω
Back switch pushed 313 to 345 Ω
Right switch pushed 950 to 1050 Ω
Left switch pushed 2955 to 3265 Ω


*1: w/ Voice Switch of Steering Pad Switch Assembly


HINT:

If the result is not as specified, replace the steering pad switch assembly.



b.

Check the illumination.

E245204
2.698,0.729 3.073,0.958 0.375,0.229 3.719,0.875 4.042,1.094 false 3.51,0.854 3.281,0.375 false 0.156,0.125 0.438,0.406 0.281,0.281 10 false *a 4.083,1.063 4.542,1.323 0.458,0.26 10 false IL+2 3.146,0.219 3.531,0.521 0.385,0.302 10 false -DP 2.802,0.771 3.052,0.969 0.25,0.198 10 false z3
*a Component without harness connected
(Steering Pad Switch Assembly)
- -


i.

Connect an auxiliary battery positive (+) lead to terminal IL+2 and a negative (-) lead to terminal -DP of the steering pad switch assembly connector.


ii.

Check that the switch illumination comes on.

OK:

Steering pad switch illumination comes on.


HINT:

If the result is not as specified, replace the steering pad switch assembly.