Home › Steering › STEERING COLUMN › STEERING LOCK SYSTEM
RM2040EQ _55 Steering _014714 STEERING COLUMN _0075005 STEERING LOCK SYSTEM U

STEERING COLUMN  STEERING LOCK SYSTEM  TERMINALS OF ECU  


TERMINAL INSPECTION


B118684
1.759,0.832 2.211,1.143 0.452,0.311 1.88,0.918 2.2,1.081 0.321,0.163 10 I24 0.282,0.128 0.511,0.292 0.228,0.163 10 *a
*a Component without harness connected
(Steering Lock ECU (Steering Lock Actuator Assembly))
- -


a.

Measure the voltage and resistance according to the value(s) in the table below.

Terminal No. (Symbol) Input/Output Wiring Color Terminal Description Condition Specified Condition Related Data List Item
I24-1 (GND) - Body ground - W-B - Body ground Ground* Always Below 1 Ω -
I24-3 (IGE) - I24-1 (GND) Input SB - W-B Steering lock motor activation command signal (motor activation command signal sent from certification ECU (smart key ECU assembly)) Any door opened when conditions below met, and then steering lock motor activated:
·

Shift lever in P

·

Steering lock unlocked in advance by carrying key and turning power switch on (IG)

·

After above conditions met, power switch turned off


Pulse generation (see waveform)
Entry&Start
·

Power Supply Short

·

Unlock Request Receive

·

Lock Request Receive


I24-4 (SLP1) - I24-1 (GND) Output P - W-B Steering lock bar position signal (output signal from steering unlock sensor) Steering locked → unlocked 11 to 14 V → Below 1.2 V
Entry&Start
·

Push Start Error

·

Sensor Value


I24-5 (LIN) - I24-1 (GND) Input/Output Y - W-B LIN communication line - -
Entry&Start
·

Steering Lock Start Cond


I24-6 (IG2) - I24-1 (GND) Input LG - W-B Power source mode signal (IG2 power supply input for entire steering lock actuator assembly)* Power switch off → power switch on (IG) Below 1 V → 11 to 14 V
Entry&Start
·

Ignition Switch


I24-7 (B) - Body ground Input B - Body ground Power source* Always 11 to 14 V -

*: When there is a problem with the power source input, the certification ECU (smart key ECU assembly) may store DTC B2786.


NOTICE:

There are 1 motor and 2 sensors built into the steering lock actuator assembly.


HINT:
·

When taking measurements when the lock motor is stopped, it is not necessary to perform any operations.

·

In order to take measurements when the lock motor is operating, perform either of the following operations:

·

To unlock the steering, carry the key and turn the power switch on (ACC) or on (IG) with the shift lever in P.

·

To lock the steering, turn the power switch off with the shift lever in P, and then open a door.




i.
C221561
0.229,0.406 1.635,0.573 1.406,0.167 1.51,1.583 2.479,1.708 0.969,0.125 2.281,0.448 2.708,0.604 0.427,0.156 1.729,1.708 1.813,1.99 1.813,1.99 1.865,1.99 false 1.635,0.438 2.75,0.198 2.75,0.198 2.823,0.198 false 2.719,0.198 2.521,0.448 false 2.927,1.573 3.302,1.719 0.375,0.146 10 GND 1.896,1.906 2.385,2.052 0.49,0.146 10 *b 2.854,0.104 3.219,0.333 0.365,0.229 10 *a
*a Steering lock motor not operating
*b Steering lock motor operating


Waveform

Item Content
Tester Connection I24-3 (IGE) - I24-1 (GND)
Tool Setting 2 V/DIV., 200 ms./DIV.
Vehicle Condition Steering lock motor not operating → Steering lock motor operating → Steering lock motor not operating