Home › Power Source / Network › NETWORKING › LIN COMMUNICATION SYSTEM
RM2040EQ _57 Power Source / Network _014721 NETWORKING _0075041 LIN COMMUNICATION SYSTEM C

NETWORKING  LIN COMMUNICATION SYSTEM  B278C  Lost Communication with Power Source Control  


DESCRIPTION

This DTC is stored when LIN communication between the certification ECU (smart key ECU assembly) and power management control ECU stops for 10 seconds or more.

DTC No. Detection Item DTC Detection Condition Trouble Area
B278C Lost Communication with Power Source Control No communication between the certification ECU (smart key ECU assembly) and power management control ECU for 10 seconds or more.
·

Power management control ECU

·

Certification ECU (smart key ECU assembly)

·

Wire harness or connector

·

AM2 fuse



WIRING DIAGRAM

B228566
0.701,3.469 2.329,3.625 1.628,0.156 10 : LIN Communication Line 0.89,2.509 2.449,2.825 1.559,0.316 10 Certification ECU (Smart Key ECU Assembly) 4.049,2.509 5.344,2.825 1.295,0.316 10 Power Management Control ECU 0.89,2.341 1.157,2.49 0.267,0.149 10 I87 1.849,1.465 2.103,1.628 0.253,0.163 10 LIN 4.231,1.465 4.568,1.628 0.337,0.163 10 LIN2 4.745,1.064 5.128,1.227 0.383,0.163 10 AM22 4.745,1.447 5.128,1.61 0.383,0.163 10 AM21 4.932,1.979 5.13,2.142 0.198,0.163 10 E1 2.155,1.332 2.335,1.474 0.179,0.142 10 12 3.961,1.475 4.159,1.624 0.198,0.149 10 I4 5.255,1.071 5.453,1.22 0.198,0.149 10 I3 5.255,1.456 5.453,1.605 0.198,0.149 10 I4 5.255,1.993 5.453,2.142 0.198,0.149 10 I3 3.954,1.297 4.152,1.446 0.198,0.149 10 11 5.285,0.895 5.386,1.045 0.101,0.149 10 1 5.285,1.283 5.386,1.432 0.101,0.149 10 7 5.285,1.825 5.386,1.974 0.101,0.149 10 6 6.02,1.218 6.333,1.381 0.314,0.163 10 AM2 4.591,0.391 5.946,0.554 1.355,0.163 10 from Auxiliary Battery

CAUTION / NOTICE / HINT

NOTICE:
·

Inspect the fuses for circuits related to this system before performing the following inspection procedure.

·

If the certification ECU (smart key ECU assembly) is replaced, register the keys (refer to the Service Bulletin).

·

When using the intelligent tester to troubleshoot with the power switch off:

Connect the intelligent tester to the DLC3, and turn the courtesy switch on and off at 1.5-second intervals until communication between the intelligent tester and vehicle begins.



PROCEDURE

1.CHECK HARNESS AND CONNECTOR (POWER MANAGEMENT CONTROL ECU - AUXILIARY BATTERY AND BODY GROUND)
a.

Disconnect the I3 and I4 power management control ECU connectors.


b.

Measure the resistance and voltage according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
I3-6 (E1) - Body ground Always Below 1 Ω


Standard Voltage:
Tester Connection Condition Specified Condition
I3-1 (AM22) - Body ground Power switch off 11 to 14 V
I4-7 (AM21) - Body ground Power switch off 11 to 14 V



Result:
Proceed to
OK
NG



OK

2.CHECK HARNESS AND CONNECTOR (CERTIFICATION ECU - POWER MANAGEMENT CONTROL ECU)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

2.CHECK HARNESS AND CONNECTOR (CERTIFICATION ECU - POWER MANAGEMENT CONTROL ECU)
a.

Disconnect the I87 certification ECU (smart key ECU assembly) connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
I87-12 (LIN) - I4-11 (LIN2) Always Below 1 Ω
I87-12 (LIN) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

3.REPLACE POWER MANAGEMENT CONTROL ECU

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

3.REPLACE POWER MANAGEMENT CONTROL ECU
a.

Replace the power management control ECU.

Click herePower Source / Network>POWER DISTRIBUTION>POWER MANAGEMENT CONTROL ECU>REMOVAL


Result:
Proceed to
NEXT



NEXT

4.CHECK DTC OUTPUT
4.CHECK DTC OUTPUT
a.

Clear the DTC.

Click herePower Source / Network>NETWORKING>LIN COMMUNICATION SYSTEM>DTC CHECK / CLEAR

Body Electrical > Entry&Start > Clear DTCs
50002 125

b.

Recheck for DTCs.

Body Electrical > Entry&Start > Trouble Codes
50001 125
OK:

DTC B278C is not output.



Result:
Proceed to
OK
NG



OK

END (POWER MANAGEMENT CONTROL ECU WAS DEFECTIVE)

NG

REPLACE CERTIFICATION ECU (SMART KEY ECU ASSEMBLY)