Home › Power Source / Network › NETWORKING › CAN COMMUNICATION SYSTEM › 2012.02–2014.05
RM2040EQ _57 Power Source / Network _014721 NETWORKING _0075042 CAN COMMUNICATION SYSTEM U

NETWORKING  CAN COMMUNICATION SYSTEM  TERMINALS OF ECU  


NOTICE:
·

After turning the power switch off, waiting time may be required before disconnecting the cable from the negative (-) auxiliary battery terminal. Therefore, make sure to read the disconnecting the cable from the negative (-) auxiliary battery terminal notices before proceeding with work.

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION

·

Turn the power switch off before measuring the resistances between CAN main bus lines and between CAN branch lines.

·

Turn the power switch off before inspecting CAN bus lines for a ground short.

·

Before measuring the resistance of the CAN bus, turn the power switch off and leave the vehicle for 1 minute or more without operating the key, switches or opening or closing the doors. After that, disconnect the cable from the negative (-) auxiliary battery terminal and leave the vehicle for 1 minute or more before measuring the resistance.

·

This section describes the standard values for all CAN related components.



HINT:
·

Operating the power switch, any other switches or a door triggers related ECU and sensor communication on the CAN. This communication will cause the resistance value to change.

·

Even after DTCs are cleared, if a DTC is stored again after driving the vehicle for a while, the malfunction may be occurring due to vibration of the vehicle. In such a case, wiggling the ECUs or wire harness while performing the inspection below may help determine the cause of the malfunction.



CAN JUNCTION RH1 CONNECTOR


a.

Check the CAN junction RH1 connector.

HINT:

Connectors that connect to the CAN junction connector can be distinguished by color of their CAN bus lines. When the connectors have been disconnected from the CAN junction connector, reconnecting the connectors to non-original positions on the CAN junction connector does not affect system performance. However, it is preferred to reconnect the connectors to their original positions to avoid negative effects on the wiring such as tension on the wiring harnesses, and to make future maintenance easier.


i.

Connection diagram

C248091C01
5.135,0.677 4.26,0.677 4.26,0.677 4.26,1.188 false 5.583,0.896 4.563,0.896 4.563,0.896 4.563,1.188 false 4.74,0.448 4.01,0.448 4.01,0.448 4.01,1.188 false 4.323,0.219 3.74,0.219 3.74,0.219 3.74,1.188 false 5.156,2.125 4.281,2.125 4.281,2.125 4.281,1.365 false 5.583,1.896 4.563,1.896 4.563,1.896 4.563,1.365 false 4.74,2.354 4.01,2.354 4.01,2.354 4.01,1.365 false 4.323,2.573 3.74,2.573 3.74,2.573 3.74,1.365 false 2,0.677 2.875,0.677 2.875,0.677 2.875,1.188 false 2.438,0.438 3.156,0.438 3.156,0.438 3.156,1.177 false 2.854,0.219 3.427,0.219 3.427,0.219 3.427,1.188 false 2,2.125 2.875,2.125 2.875,2.125 2.875,1.365 false 2.417,2.354 3.135,2.354 3.135,2.354 3.135,1.365 false 2.833,2.573 3.406,2.573 3.406,2.573 3.406,1.365 false 0.146,0.125 0.313,0.281 0.167,0.156 10 false *a 4.375,0.125 4.927,0.281 0.552,0.156 10 false CANH*e 4.802,0.354 5.354,0.51 0.552,0.156 10 false CANH*f 5.229,0.594 5.885,0.781 0.656,0.188 10 false CANH*g 5.219,2.042 5.948,2.24 0.729,0.198 10 false CANL*g 4.792,2.271 5.521,2.469 0.729,0.198 10 false CANL*f 4.406,2.5 5.104,2.698 0.698,0.198 10 false CANL*e 5.646,0.823 6.198,0.979 0.552,0.156 10 false CANH*h 5.615,1.813 6.167,1.969 0.552,0.156 10 false CANL*h 2.313,0.146 2.865,0.302 0.552,0.156 10 false CANH*d 1.896,0.354 2.448,0.51 0.552,0.156 10 false CANH*c 1.458,0.604 2.01,0.76 0.552,0.156 10 false CANH*b 1.479,2.031 2.031,2.188 0.552,0.156 10 false CANL*b 1.906,2.26 2.458,2.417 0.552,0.156 10 false CANL*c 2.323,2.479 2.979,2.646 0.656,0.167 10 false CANL*d
*a Component with harness connected
(CAN Junction RH1 Connector)
*b to Headlight Swivel ECU Assembly (AFS ECU)*1
(for V Bus)
*c to Steering Sensor
(for V Bus)
*d to Brake Booster with Master Cylinder Assembly (Skid Control ECU)
(for V Bus)
*e to Smart Key ECU Assembly (Certification ECU)
(for V Bus)
*f to DLC3
*g to Combination Meter Assembly
(for V Bus)
*h to CAN Junction LH1 Connector
(for V Bus)


*1: w/ Automatic High Beam System


ii.

Check the connection diagram of the components which are connected to the CAN junction RH1 connector.

Terminal No. (Symbol) Wiring Color Connected to
I112-1 (CANH) BE Headlight swivel ECU assembly (AFS ECU)*1
(for V bus)
I112-2 (CANL) W
I97-1 (CANH) V Steering sensor
(for V bus)
I97-2 (CANL) W
I110-1 (CANH) Y Brake booster with master cylinder assembly (Skid control ECU)
(for V bus)
I110-2 (CANL) W
I106-1 (CANH) L Smart key ECU assembly (Certification ECU)
(for V bus)
I106-2 (CANL) W
I96-1 (CANH) G DLC3
I96-2 (CANL) W
I94-1 (CANH) R Combination meter assembly
(for V bus)
I94-2 (CANL) W
I101-1 (CANH) B CAN junction LH1 connector
(for V bus)
I101-2 (CANL) W

*1: w/ Automatic High Beam System




CAN JUNCTION LH1 CONNECTOR


a.

Check the CAN junction LH1 connector.

HINT:

Connectors that connect to the CAN junction connector can be distinguished by color of their CAN bus lines. When the connectors have been disconnected from the CAN junction connector, reconnecting the connectors to non-original positions on the CAN junction connector does not affect system performance. However, it is preferred to reconnect the connectors to their original positions to avoid negative effects on the wiring such as tension on the wiring harnesses, and to make future maintenance easier.


i.

Connection diagram

C239444C06
5.156,0.667 4.281,0.667 4.281,0.667 4.281,1.188 false 5.573,0.896 4.563,0.896 4.563,0.896 4.563,1.188 false 4.74,0.448 4.01,0.448 4.01,0.448 4.01,1.188 false 4.313,0.219 3.74,0.219 3.74,0.219 3.74,1.188 false 5.156,2.125 4.281,2.125 4.281,2.125 4.281,1.365 false 5.573,1.896 4.563,1.896 4.563,1.896 4.563,1.365 false 4.74,2.344 4.01,2.344 4.01,2.344 4.01,1.365 false 4.313,2.573 3.74,2.573 3.74,2.573 3.74,1.365 false 2.01,0.656 2.885,0.656 2.885,0.656 2.885,1.177 false 1.594,0.885 2.615,0.885 2.615,0.885 2.615,1.177 false 2.427,0.438 3.156,0.438 3.156,0.438 3.156,1.177 false 2.854,0.208 3.427,0.208 3.427,0.208 3.427,1.177 false 2,2.125 2.875,2.125 2.875,2.125 2.875,1.365 false 1.583,1.896 2.604,1.896 2.604,1.896 2.604,1.365 false 2.417,2.344 3.146,2.344 3.146,2.344 3.146,1.365 false 2.844,2.573 3.417,2.573 3.417,2.573 3.417,1.365 false 0.146,0.125 0.313,0.281 0.167,0.156 10 false *a 4.354,0.125 4.958,0.354 0.604,0.229 10 false CANH*f 4.771,0.354 5.417,0.552 0.646,0.198 10 false CANH*g 5.198,0.573 5.75,0.729 0.552,0.156 10 false CANH*h 5.188,2.042 5.74,2.198 0.552,0.156 10 false CANL*h 4.76,2.271 5.406,2.5 0.646,0.229 10 false CANL*g 4.344,2.49 4.896,2.646 0.552,0.156 10 false CANL*f 5.604,0.813 6.281,1.031 0.677,0.219 10 false CANH*i 5.604,1.823 6.156,1.979 0.552,0.156 10 false CANL*i 2.302,0.125 2.854,0.281 0.552,0.156 10 false CANH*e 1.875,0.354 2.427,0.51 0.552,0.156 10 false CANH*d 1.458,0.573 2.01,0.729 0.552,0.156 10 false CANH*c 1.458,2.042 2.01,2.198 0.552,0.156 10 false CANL*c 1.875,2.271 2.427,2.427 0.552,0.156 10 false CANL*d 2.302,2.49 2.854,2.646 0.552,0.156 10 false CANL*e 1.042,0.823 1.594,0.979 0.552,0.156 10 false CANH*b 1.042,1.823 1.594,1.979 0.552,0.156 10 false CANL*b
*a Component with harness connected
(CAN Junction LH1 Connector)
*b to Power Management Control ECU
(for V Bus)
*c to Main Body ECU (Multiplex Network Body ECU)
(for V Bus)
*d to Air Conditioning Amplifier Assembly
(for V Bus)
*e to Airbag Sensor Assembly
(for V Bus)
*f to Power Steering ECU Assembly
(for V Bus)
*g to ECM
(for V Bus)
*h
·

Navigation ECU Sub-assembly*1

·

Radio and Display Receiver Assembly*2


(for V Bus)
*i to CAN Junction RH1 Connector
(for V Bus)
- -


·

*1: for Navigation receiver type

·

*2: for Radio and display type



ii.

Check the connection diagram of the components which are connected to the CAN junction LH1 connector.

Terminal No. (Symbol) Wiring Color Connected to
I109-1 (CANH) BE Power management control ECU
(for V bus)
I109-2 (CANL) W
I95-1 (CANH) P Main body ECU (Multiplex network body ECU)
(for V bus)
I95-2 (CANL) W
I102-1 (CANH) V Air conditioning amplifier assembly
(for V bus)
I102-2 (CANL) W
I103-1 (CANH) Y Airbag sensor assembly
(for V bus)
I103-2 (CANL) W
I100-1 (CANH) L Power steering ECU assembly
(for V bus)
I100-2 (CANL) W
I104-1 (CANH) G ECM
(for V bus)
I104-2 (CANL) W
I107-1 (CANH) R
·

Navigation ECU sub-assembly*1

·

Radio and display receiver assembly*2


(for V bus)
I107-2 (CANL) W
I93-1 (CANH) B CAN junction RH1 connector
(for V bus)
I93-2 (CANL) W

·

*1: for Navigation receiver type

·

*2: for Radio and display type





CAN NO. 1 JUNCTION CONNECTOR


a.

Check the CAN No. 1 junction connector.

i.

Connection diagram

C234761C18
3.438,0.167 3.823,0.417 0.385,0.25 3.188,1.417 2.5,0.927 2.5,0.927 2.167,0.927 false 3.354,1.406 2.521,0.531 2.521,0.531 2.188,0.531 false 3.219,1.719 2.531,2.094 2.531,2.094 2.198,2.094 false 3.365,1.719 2.531,2.438 2.531,2.438 2.198,2.438 false 3.5,1.406 4.302,0.531 4.302,0.531 4.604,0.531 false 3.51,1.719 4.313,2.438 4.313,2.438 4.615,2.438 false 0.115,0.083 0.49,0.625 0.375,0.542 10 false *a 1.635,0.427 2.396,0.677 0.76,0.25 10 false CANH*c 1.677,2.365 2.417,2.604 0.74,0.24 10 false CANL*c 1.583,0.823 2.333,1.094 0.75,0.271 10 false CANH*b 1.688,2.031 2.417,2.271 0.729,0.24 10 false CANL*b 4.688,0.427 5.333,0.667 0.646,0.24 10 false CANH*d 4.688,2.375 5.333,2.615 0.646,0.24 10 false CANL*d 3.5,0.198 4.385,0.521 0.885,0.323 10 false A72
*a Front view of wire harness connector
(to CAN No. 1 Junction Connector)
*b to Brake Booster with Master Cylinder Assembly (Skid Control ECU)
(for Sub Bus 15)
*c to ECM
(for Sub Bus 15)
*d to Power Management Control ECU
(for Sub Bus 15)



ii.

Check the connection diagram of the components which are connected to the CAN No. 1 junction connector.

Terminal No. (Symbol) Wiring Color Connected to
A72-1 (CANH) B Brake booster with master cylinder assembly (Skid control ECU)
(for Sub bus 15)
A72-7 (CANL) W
A72-2 (CANH) B ECM
(for Sub bus 15)
A72-8 (CANL) W
A72-3 (CANH) B Power management control ECU
(for Sub bus 15)
A72-9 (CANL) W




CAN JUNCTION LH2 CONNECTOR (w/ Seat Position Memory System)


a.

Check the CAN junction LH2 connector.

HINT:

Connectors that connect to the CAN junction connector can be distinguished by color of their CAN bus lines. When the connectors have been disconnected from the CAN junction connector, reconnecting the connectors to non-original positions on the CAN junction connector does not affect system performance. However, it is preferred to reconnect the connectors to their original positions to avoid negative effects on the wiring such as tension on the wiring harnesses, and to make future maintenance easier.


i.

Connection diagram

C247999C08
6.198,1.74 6.469,2.542 false 1.135,4.688 1.573,4.531 false 1.583,5.031 1.146,4.875 false 0.083,0.094 0.531,0.417 0.448,0.323 10 false *1 1.354,0.656 1.802,0.979 0.448,0.323 10 false *a 4.427,0.656 4.865,0.979 0.438,0.323 10 false *b 6.406,2.563 6.854,2.885 0.448,0.323 10 false *c 0.563,4.094 1.01,4.417 0.448,0.323 10 false *d 1.615,4.458 2.146,4.688 0.531,0.229 10 false CANH 1.615,4.969 2.146,5.198 0.531,0.229 10 false CANL 4.615,4.833 5.073,5.042 0.458,0.208 10 false I162 4.615,4.469 5.073,4.677 0.458,0.208 10 false I163 4.615,5.188 5.073,5.396 0.458,0.208 10 false I166
*1 CAN Junction LH2 Connector - -
*a Junction Connector A Side *b Junction Connector B Side
*c Earth Terminal *d Front view of wire harness connector
(to CAN Junction LH2 Connector)




b.

Check the connection diagram of the components which are connected to the CAN junction LH2 connector.

Junction Connector B Side
Terminal No. (Symbol) Wiring Color Connected to
I162-1 (CANH) R Main body ECU (Multiplex network body ECU)
(for Sub bus 1)
I162-2 (CANL) GR
I163-1 (CANH) G Outer mirror control ECU assembly (for Front passenger side)
(for Sub bus 1)
I163-2 (CANL) GR
I166-1 (CANH) Y CAN junction RH2 connector
(for Sub bus 1)
I166-2 (CANL) GR



CAN JUNCTION RH2 CONNECTOR (w/ Seat Position Memory System)


a.

Check the CAN junction RH2 connector.

HINT:

Connectors that connect to the CAN junction connector can be distinguished by color of their CAN bus lines. When the connectors have been disconnected from the CAN junction connector, reconnecting the connectors to non-original positions on the CAN junction connector does not affect system performance. However, it is preferred to reconnect the connectors to their original positions to avoid negative effects on the wiring such as tension on the wiring harnesses, and to make future maintenance easier.


i.

Connection diagram

C259930C04
6.198,1.74 6.469,2.542 false 1.135,4.688 1.573,4.542 false 1.573,5.031 1.135,4.875 false 0.094,0.073 0.531,0.396 0.438,0.323 10 false *1 1.354,0.646 1.792,0.969 0.438,0.323 10 false *a 4.438,0.656 4.875,0.979 0.438,0.323 10 false *b 6.406,2.563 6.844,2.885 0.438,0.323 10 false *c 0.563,4.052 1,4.375 0.438,0.323 10 false *d 1.594,4.458 2.125,4.688 0.531,0.229 10 false CANH 1.594,4.969 2.125,5.198 0.531,0.229 10 false CANL 4.615,4.833 5.073,5.042 0.458,0.208 10 false I164 4.615,4.469 5.073,4.677 0.458,0.208 10 false I165 4.615,3.75 5.073,3.958 0.458,0.208 10 false I168 4.615,5.177 5.073,5.385 0.458,0.208 10 false I167
*1 CAN Junction RH2 Connector - -
*a Junction Connector A Side *b Junction Connector B Side
*c Earth Terminal *d Front view of wire harness connector
(to CAN Junction RH2 Connector)




b.

Check the connection diagram of the components which are connected to the CAN junction RH2 connector.

Junction Connector B Side
Terminal No. (Symbol) Wiring Color Connected to
I168-1 (GND) W-B Body ground
(for Sub bus 1)
I167-1 (CANH) Y CAN junction LH2 connector
(for Sub bus 1)
I167-2 (CANL) GR
I165-1 (CANH) BE Position control ECU and switch assembly (for Driver side)
(for Sub bus 1)
I165-2 (CANL) GR
I164-1 (CANH) P Outer mirror control ECU assembly (for Driver side)
(for Sub bus 1)
I164-2 (CANL) GR



CAN NO. 2 JUNCTION CONNECTOR (w/ Blind Spot Monitor System)


a.

Check the CAN No. 2 junction connector.

i.
C238890C32
0.406,1.146 0.823,1.385 0.417,0.24 2.427,0.281 2.104,0.281 2.104,0.281 2.104,1.375 false 2.521,0.521 2.198,0.521 2.198,0.521 2.198,1.365 false 2.635,0.781 2.313,0.781 2.313,0.781 2.313,1.365 false 2.646,1.896 2.323,1.896 2.323,1.896 2.323,1.583 false 1.26,1.896 2.094,1.896 2.094,1.896 2.094,1.583 false 2.052,2.073 2.208,2.073 2.208,2.073 2.208,1.583 false 0.177,0.156 0.323,0.313 0.146,0.156 10 false *a 2.448,0.177 3.094,0.354 0.646,0.177 10 false CANH*b 2.563,0.427 3.177,0.615 0.615,0.188 10 false CANH*c 2.698,0.698 3.302,0.906 0.604,0.208 10 false CANH*d 2.677,1.802 3.229,1.958 0.552,0.156 10 false CANL*d 0.688,1.813 1.24,1.969 0.552,0.156 10 false CANL*b 1.385,1.979 1.938,2.135 0.552,0.156 10 false CANL*c 0.49,1.188 0.813,1.354 0.323,0.167 10 false O30
*a Front view of wire harness connector
(to CAN No. 2 Junction Connector)
*b to Blind Spot Monitor Sensor RH
(for Sub Bus 11)
*c to CAN No. 3Junction Connector
(for Sub Bus 11)
*d to Power Management Control ECU
(for Sub Bus 11)


Connection diagram


ii.

Check the connection diagram of the components which are connected to the CAN No. 2 junction connector.

Terminal No. (Symbol) Wiring Color Connected to
O30-9 (CANH) R Blind spot monitor sensor RH
(for Sub bus 11)
O30-20 (CANL) B
O30-10 (CANH) G CAN No. 3 junction connector
(for Sub bus 11)
O30-21 (CANL) B
O30-11 (CANH) V Power management control ECU
(for Sub bus 11)
O30-22 (CANL) B




CAN NO. 3 JUNCTION CONNECTOR (w/ Blind Spot Monitor System)


a.

Check the CAN No. 3 junction connector.

i.
C238890C19
0.479,1.135 0.896,1.375 0.417,0.24 2.427,0.271 2.104,0.271 2.104,0.271 2.104,1.365 false 2.542,0.521 2.219,0.521 2.219,0.521 2.219,1.365 false 2.656,0.781 2.333,0.781 2.333,0.781 2.333,1.365 false 2.646,1.896 2.323,1.896 2.323,1.896 2.323,1.583 false 1.26,1.896 2.094,1.896 2.094,1.896 2.094,1.583 false 2.052,2.073 2.208,2.073 2.208,2.073 2.208,1.583 false 0.177,0.156 0.323,0.313 0.146,0.156 10 false *a 2.5,0.198 3.052,0.354 0.552,0.156 10 false CANH*b 2.604,0.448 3.156,0.604 0.552,0.156 10 false CANH*c 2.719,0.708 3.271,0.865 0.552,0.156 10 false CANH*d 2.677,1.813 3.229,1.969 0.552,0.156 10 false CANL*d 0.74,1.823 1.292,1.979 0.552,0.156 10 false CANL*b 1.531,2.01 2.083,2.167 0.552,0.156 10 false CANL*c 0.573,1.188 0.969,1.521 0.396,0.333 10 false T15
*a Front view of wire harness connector
(to CAN No. 3 Junction Connector)
*b to CAN No. 4 Junction Connector
(for Sub Bus 11)
*c to Blind Spot Monitor Sensor LH
(for Sub Bus 11)
*d to CAN No. 2 Junction Connector
(for Sub Bus 11)


Connection diagram


ii.

Check the connection diagram of the components which are connected to the CAN No. 3 junction connector.

Terminal No. (Symbol) Wiring Color Connected to
T15-9 (CANH) L CAN No. 4 junction connector
(for Sub bus 11)
T15-20 (CANL) B
T15-10 (CANH) R Blind spot monitor sensor LH
(for Sub bus 11)
T15-21 (CANL) B
T15-11 (CANH) G CAN No. 2 junction connector
(for Sub bus 11)
T15-22 (CANL) B




CAN NO. 4 JUNCTION CONNECTOR (w/ Blind Spot Monitor System)


a.

Check the CAN No. 4 junction connector.

i.
C183982C17
1.781,2.063 2.198,2.302 0.417,0.24 0.938,0.844 0.635,0.844 0.635,0.844 0.635,2.177 false 1.219,1.188 0.917,1.188 0.917,1.188 0.917,2.177 false 0.177,0.115 0.333,0.292 0.156,0.177 10 false *a 0.99,0.75 1.563,0.906 0.573,0.156 10 false CANH*b 1.271,1.104 1.833,1.26 0.563,0.156 10 false CANL*b 1.875,2.104 2.438,2.5 0.563,0.396 10 false T16
*a Rear view of wire harness connector
(to CAN No. 4 Junction Connector)
*b to CAN No. 3 Junction Connector
(for Sub Bus 11)


Connection diagram


ii.

Check the connection diagram of the components which are connected to the CAN No. 4 junction connector.

Terminal No. (Symbol) Wiring Color Connected to
T16-3 (CANH) L CAN No. 3 junction connector
(for Sub bus 11)
T16-2 (CANL) B




DLC3


a.

Disconnect the cable from the negative (-) auxiliary battery terminal.


b.

Measure the resistance according to the value(s) in the table below.

C188081C02
1.5,1.552 1.875,1.771 0.375,0.219 4.198,1.969 4.479,2.354 false 4.26,0.875 3.833,1.406 false 3.052,0.875 3.479,1.406 false 3.844,1.969 3.552,2.354 false 0.188,0.167 0.708,0.333 0.521,0.167 10 false *1 1.594,1.573 1.917,1.781 0.323,0.208 10 false I39 3.365,2.365 3.813,2.531 0.448,0.167 10 false CANL 4.313,0.771 4.76,0.938 0.448,0.167 10 false CANH 4.385,2.375 4.74,2.542 0.354,0.167 10 false BAT 2.802,0.75 3.156,0.917 0.354,0.167 10 false CG
*1 DLC3 - -


Standard Resistance:
Terminal No. (Symbol) Wiring Color Terminal Description Condition Specified Condition
I39-6 (CANH) - I39-14 (CANL) G - W HIGH-level CAN bus line - LOW-level CAN bus line Cable disconnected from negative (-) auxiliary battery terminal 54 to 69 Ω
I39-6 (CANH) - I39-4 (CG) G - W-B HIGH-level CAN bus line - Ground Cable disconnected from negative (-) auxiliary battery terminal 200 Ω or higher
I39-14 (CANL) - I39-4 (CG) W - W-B LOW-level CAN bus line - Ground Cable disconnected from negative (-) auxiliary battery terminal 200 Ω or higher
I39-6 (CANH) - I39-16 (BAT) G - R HIGH-level CAN bus line - Auxiliary battery positive (+) Cable disconnected from negative (-) auxiliary battery terminal 6 kΩ or higher
I39-14 (CANL) - I39-16 (BAT) W - R LOW-level CAN bus line - Auxiliary battery positive (+) Cable disconnected from negative (-) auxiliary battery terminal 6 kΩ or higher




POWER MANAGEMENT CONTROL ECU


C146689C23
1.354,1.438 1.688,1.635 0.333,0.198 2.802,1.438 3.135,1.635 0.333,0.198 4.26,1.438 4.563,1.635 0.302,0.198 5.531,1.438 5.833,1.635 0.302,0.198 0.115,0.094 0.313,0.396 0.198,0.302 10 false *a 1.406,1.448 1.802,1.698 0.396,0.25 10 false A38 2.854,1.448 3.281,1.698 0.427,0.25 10 false A39 4.354,1.448 4.677,1.708 0.323,0.26 10 false I3 5.635,1.448 5.906,1.677 0.271,0.229 10 false I4
*a Component without harness connected
(Power Management Control ECU)
- -


a.

Disconnect the cable from the negative (-) auxiliary battery terminal.


b.
A204446C42
2.438,2.885 2.927,3.177 0.49,0.292 2.469,2.5 1.667,2.219 false 2.427,2.51 1.677,2.573 false 2.427,2.354 2.104,2.094 false 2.635,2.354 3.021,2.073 false 1.698,2.771 2.417,2.573 false 1.688,3.125 2.469,2.573 false 2.615,2.938 2.885,3.135 0.271,0.198 10 false I4 1.271,2.135 1.708,2.365 0.438,0.229 10 false CA1L 1.26,2.469 1.646,2.646 0.385,0.177 10 false CA1H 1.271,2.708 1.781,2.958 0.51,0.25 10 false CA3P 1.271,3.063 1.813,3.271 0.542,0.208 10 false CA3N 0.115,0.115 0.438,0.396 0.323,0.281 10 false *a 1.719,2.01 2.125,2.229 0.406,0.219 10 false AM21 3.063,1.969 3.375,2.219 0.313,0.25 10 false E12
*a Rear view of wire harness connector
(to Power Management Control ECU)


Disconnect the power management control ECU connectors.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
V Bus Branch Lines
Terminal No. (Symbol) Wiring Color Terminal Description Condition Specified Condition
I4-25 (CA1H) - I4-24 (CA1L) BE - W HIGH-level CAN bus line - LOW-level CAN bus line Cable disconnected from negative (-) auxiliary battery terminal 54 to 69 Ω
I4-25 (CA1H) - I4-4 (E12) BE - BR HIGH-level CAN bus line - Ground Cable disconnected from negative (-) auxiliary battery terminal 200 Ω or higher
I4-24 (CA1L) - I4-4 (E12) W - BR LOW-level CAN bus line - Ground Cable disconnected from negative (-) auxiliary battery terminal 200 Ω or higher
I4-25 (CA1H) - I4-7 (AM21) BE - L HIGH-level CAN bus line - Auxiliary battery positive (+) Cable disconnected from negative (-) auxiliary battery terminal 6 kΩ or higher
I4-24 (CA1L) - I4-7 (AM21) W - L LOW-level CAN bus line - Auxiliary battery positive (+) Cable disconnected from negative (-) auxiliary battery terminal 6 kΩ or higher


Standard Resistance:
Sub Bus 15 Main Lines
Terminal No. (Symbol) Wiring Color Terminal Description Condition Specified Condition
I4-31 (CA3P) - I4-30 (CA3N) B - W HIGH-level CAN bus line - LOW-level CAN bus line Cable disconnected from negative (-) auxiliary battery terminal 108 to 132 Ω
I4-31 (CA3P) - I4-4 (E12) B - BR HIGH-level CAN bus line - Ground Cable disconnected from negative (-) auxiliary battery terminal 200 Ω or higher
I4-30 (CA3N) - I4-4 (E12) W - BR LOW-level CAN bus line - Ground Cable disconnected from negative (-) auxiliary battery terminal 200 Ω or higher
I4-31 (CA3P) - I4-7 (AM21) B - L HIGH-level CAN bus line - Auxiliary battery positive (+) Cable disconnected from negative (-) auxiliary battery terminal 6 kΩ or higher
I4-30 (CA3N) - I4-7 (AM21) W - L LOW-level CAN bus line - Auxiliary battery positive (+) Cable disconnected from negative (-) auxiliary battery terminal 6 kΩ or higher



d.

Disconnect the cable from the negative (-) auxiliary battery terminal.


e.
A204445C85
1.917,2.969 2.406,3.26 0.49,0.292 1.833,2.354 1.625,2.198 false 2.229,2.365 2.458,2.24 false 1.823,2.573 1.594,2.604 false 1.865,2.573 1.646,2.896 false 2.094,3.021 2.344,3.25 0.25,0.229 10 false I3 0.115,0.115 0.625,0.365 0.51,0.25 10 false *a 1.417,2.104 1.833,2.365 0.417,0.26 10 false E1 2.5,2.146 2.979,2.417 0.479,0.271 10 false AM22 1.229,2.521 1.76,2.729 0.531,0.208 10 false CA2L 1.229,2.844 1.76,3.104 0.531,0.26 10 false CA2H
*a Rear view of wire harness connector
(to Power Management Control ECU)


Disconnect the power management control ECU connectors.


f.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Sub Bus 11 Main Lines
Terminal No. (Symbol) Wiring Color Terminal Description Condition Specified Condition
I3-34 (CA2H) - I3-35 (CA2L) G - LG HIGH-level CAN bus line - LOW-level CAN bus line Cable disconnected from negative (-) auxiliary battery terminal 108 to 132 Ω
I3-34 (CA2H) - I3-6 (E1) G - BR HIGH-level CAN bus line - Ground Cable disconnected from negative (-) auxiliary battery terminal 200 Ω or higher
I3-35 (CA2L) - I3-6 (E1) LG - BR LOW-level CAN bus line - Ground Cable disconnected from negative (-) auxiliary battery terminal 200 Ω or higher
I3-34 (CA2H) - I3-1 (AM22) G - SB HIGH-level CAN bus line - Auxiliary battery positive (+) Cable disconnected from negative (-) auxiliary battery terminal 6 kΩ or higher
I3-35 (CA2L) - I3-1 (AM22) LG - SB LOW-level CAN bus line - Auxiliary battery positive (+) Cable disconnected from negative (-) auxiliary battery terminal 6 kΩ or higher




ECM


A262466C04
2.479,0.406 2.854,0.635 0.375,0.229 5.781,0.406 6.156,0.635 0.375,0.229 2.552,0.438 2.875,0.604 0.323,0.167 10 false E28 5.854,0.438 6.177,0.604 0.323,0.167 10 false A25 0.083,0.094 0.74,0.469 0.656,0.375 10 false *a
*a Component without harness connected
(ECM)
- -


a.

Disconnect the cable from the negative (-) auxiliary battery terminal.


b.

Disconnect the ECM connectors.

C250518C04
1.813,0.49 2.208,0.729 0.396,0.24 4.313,0.5 4.708,0.74 0.396,0.24 5.104,0.615 4.813,0.615 4.813,0.615 4.813,1.26 false 2.813,0.615 2.51,0.615 2.51,0.615 2.51,1.25 false 2.75,0.302 2.448,0.302 2.448,0.302 2.448,1.25 false 2.813,2.156 2.51,2.156 2.51,2.156 2.51,1.313 false 2.74,2.49 2.448,2.49 2.448,2.49 2.448,1.313 false 1.24,0.615 1.531,0.615 1.531,0.615 1.531,1.25 false 0.146,0.125 0.313,0.281 0.167,0.156 10 false *a 5.146,0.542 5.333,0.698 0.188,0.156 10 false E1 2.854,0.542 3.271,0.698 0.417,0.156 10 false CANH 2.781,0.219 3.198,0.375 0.417,0.156 10 false CANP 2.854,2.083 3.271,2.24 0.417,0.156 10 false CANL 2.781,2.417 3.198,2.573 0.417,0.156 10 false CANN 0.844,0.542 1.302,0.698 0.458,0.156 10 false BATT 1.885,0.521 2.167,0.698 0.281,0.177 10 false A25 4.385,0.531 4.667,0.708 0.281,0.177 10 false E28
*a Front view of wire harness connector
(to ECM)
- -



c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
V Bus Main Lines
Terminal No. (Symbol) Wiring Color Terminal Description Condition Specified Condition
A25-13 (CANH) - A25-26 (CANL) B - W HIGH-level CAN bus line - LOW-level CAN bus line Cable disconnected from negative (-) auxiliary battery terminal 108 to 132 Ω
A25-13 (CANH) - E28-16 (E1) B - BR HIGH-level CAN bus line - Ground Cable disconnected from negative (-) auxiliary battery terminal 200 Ω or higher
A25-26 (CANL) - E28-16 (E1) W - BR LOW-level CAN bus line - Ground Cable disconnected from negative (-) auxiliary battery terminal 200 Ω or higher
A25-13 (CANH) - A25-1 (BATT) B - GR HIGH-level CAN bus line - Auxiliary battery positive (+) Cable disconnected from negative (-) auxiliary battery terminal 6 kΩ or higher
A25-26 (CANL) - A25-1 (BATT) W - GR LOW-level CAN bus line - Auxiliary battery positive (+) Cable disconnected from negative (-) auxiliary battery terminal 6 kΩ or higher


Standard Resistance:
Sub Bus 15 Main Lines
Terminal No. (Symbol) Wiring Color Terminal Description Condition Specified Condition
A25-12 (CANP) - A25-25 (CANN) B - W HIGH-level CAN bus line - LOW-level CAN bus line Cable disconnected from negative (-) auxiliary battery terminal 108 to 132 Ω
A25-12 (CANP) - E28-16 (E1) B - BR HIGH-level CAN bus line - Ground Cable disconnected from negative (-) auxiliary battery terminal 200 Ω or higher
A25-25 (CANN) - E28-16 (E1) W - BR LOW-level CAN bus line - Ground Cable disconnected from negative (-) auxiliary battery terminal 200 Ω or higher
A25-12 (CANP) - A25-1 (BATT) B - GR HIGH-level CAN bus line - Auxiliary battery positive (+) Cable disconnected from negative (-) auxiliary battery terminal 6 kΩ or higher
A25-25 (CANN) - A25-1 (BATT) W - GR LOW-level CAN bus line - Auxiliary battery positive (+) Cable disconnected from negative (-) auxiliary battery terminal 6 kΩ or higher




COMBINATION METER ASSEMBLY


E224288C06
1.76,0.219 2.135,0.448 0.375,0.229 5.021,0.219 5.396,0.448 0.375,0.229 1.865,0.25 2.219,0.531 0.354,0.281 10 false I18 5.125,0.25 5.5,0.583 0.375,0.333 10 false I17 0.125,0.094 0.469,0.396 0.344,0.302 10 false *a
*a Component without harness connected
(Combination Meter Assembly)
- -


a.

Disconnect the cable from the negative (-) auxiliary battery terminal.


b.
E224284C25
1.406,0.24 1.896,0.531 0.49,0.292 1.365,2.156 1.365,2.625 1.365,2.625 1.552,2.625 false 1.24,2.156 1.24,2.625 1.24,2.625 1.052,2.625 false 0.979,1.906 0.979,0.854 0.979,0.854 0.698,0.854 false 1.729,1.896 1.729,0.854 1.729,0.854 1.948,0.854 false 0.104,0.104 0.385,0.385 0.281,0.281 10 false *a 1.615,2.531 2.146,2.771 0.531,0.24 10 false CANH 0.677,2.552 1.208,2.792 0.531,0.24 10 false CANL 0.542,0.76 0.844,1.021 0.302,0.26 10 false B 2.021,0.75 2.333,1.021 0.313,0.271 10 false ES 1.552,0.292 1.833,0.469 0.281,0.177 10 false I18
*a Front view of wire harness connector
(to Combination Meter Assembly)


Disconnect the combination meter assembly connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Terminal No. (Symbol) Wiring Color Terminal Description Condition Specified Condition
I18-16 (CANH) - I18-15 (CANL) R - W HIGH-level CAN bus line - LOW-level CAN bus line Cable disconnected from negative (-) auxiliary battery terminal 108 to 132 Ω
I18-16 (CANH) - I18-7 (ES) R - BR HIGH-level CAN bus line - Ground Cable disconnected from negative (-) auxiliary battery terminal 200 Ω or higher
I18-15 (CANL) - I18-7 (ES) W - BR LOW-level CAN bus line - Ground Cable disconnected from negative (-) auxiliary battery terminal 200 Ω or higher
I18-16 (CANH) - I18-1 (B) R - W HIGH-level CAN bus line - Auxiliary battery positive (+) Cable disconnected from negative (-) auxiliary battery terminal 6 kΩ or higher
I18-15 (CANL) - I18-1 (B) W - W LOW-level CAN bus line - Auxiliary battery positive (+) Cable disconnected from negative (-) auxiliary battery terminal 6 kΩ or higher




INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY AND MAIN BODY ECU (MULTIPLEX NETWORK BODY ECU)


B278841C62
2.188,3.771 2.51,3.979 0.323,0.208 5.833,5.042 6.156,5.25 0.323,0.208 3.865,5.01 4.188,5.219 0.323,0.208 1.083,5.01 1.406,5.219 0.323,0.208 1.74,6.292 2.063,6.5 0.323,0.208 4.885,6.292 5.208,6.5 0.323,0.208 3.375,7.531 3.698,7.74 0.323,0.208 4.646,3.771 4.969,3.979 0.323,0.208 4.042,1.125 4.042,0.844 4.042,0.844 4.156,0.844 false 1.677,1.594 1.938,1.594 false 1.677,1.99 1.938,1.99 false 1.031,2.76 0.583,2.76 false 1.688,0.958 1.813,0.729 1.813,0.729 1.969,0.729 false 1.563,1.625 1.479,1.625 1.479,1.625 1.479,3.167 false 1.563,2.021 1.479,2.021 false 4.208,0.781 4.594,1 0.385,0.219 10 false MB 3.438,7.552 3.906,7.813 0.469,0.26 10 false MB 0.906,1.479 1.104,1.615 0.198,0.135 10 false 3C 1.156,5.031 1.354,5.167 0.198,0.135 10 false 3C 5.865,1.427 6.063,1.563 0.198,0.135 10 false 3B 1.823,6.313 2.021,6.448 0.198,0.135 10 false 3B 5.865,2.115 6.052,2.25 0.188,0.135 10 false 3A 4.969,6.313 5.156,6.448 0.188,0.135 10 false 3A 0.917,2.104 1.115,2.24 0.198,0.135 10 false 3D 3.938,5.031 4.135,5.167 0.198,0.135 10 false 3D 1.99,1.521 2.344,1.74 0.354,0.219 10 false I13 4.719,3.802 4.979,3.938 0.26,0.135 10 false I13 1.99,1.906 2.375,2.156 0.385,0.25 10 false I12 2.26,3.802 2.521,3.938 0.26,0.135 10 false I12 0.406,2.688 0.667,2.927 0.26,0.24 10 false 3F 5.906,5.063 6.094,5.198 0.188,0.135 10 false 3F 0.156,0.156 0.521,0.479 0.365,0.323 10 false *a 2,0.667 2.302,0.938 0.302,0.271 10 false *1 1.417,3.188 1.719,3.458 0.302,0.271 10 false *2
*1 Main Body ECU (Multiplex Network Body ECU)) *2 2 connectors
*a Component without harness connected
(Instrument Panel Junction Block Assembly and Main Body ECU (Multiplex Network Body ECU))
- -


B282096C66
2.26,3.823 2.583,4.031 0.323,0.208 3.938,5.083 4.26,5.292 0.323,0.208 1.156,5.063 1.479,5.271 0.323,0.208 1.813,6.344 2.135,6.552 0.323,0.208 4.969,6.344 5.292,6.552 0.323,0.208 3.448,7.583 3.771,7.792 0.323,0.208 4.719,3.823 5.042,4.031 0.323,0.208 5.802,5.063 6.125,5.271 0.323,0.208 4.115,1.135 4.115,0.854 4.115,0.854 4.229,0.854 false 1.813,2.146 2.104,2.146 false 1.813,1.792 2.094,1.792 false 0.76,2.781 1.031,2.781 false 1.865,0.979 2.073,0.552 2.073,0.552 2.188,0.552 false 1.594,3.177 1.594,1.5 1.594,1.5 1.708,1.5 false 1.594,1.865 1.698,1.865 false 1.594,2.208 1.698,2.208 false 3.51,7.604 3.875,7.854 0.365,0.25 10 false MB 1.229,5.083 1.594,5.354 0.365,0.271 10 false 3C 1.896,6.365 2.208,6.635 0.313,0.271 10 false 3B 5.042,6.365 5.469,6.583 0.427,0.219 10 false 3A 4.01,5.104 4.385,5.438 0.375,0.333 10 false 3D 4.792,3.854 5.073,4.073 0.281,0.219 10 false I13 2.333,3.854 2.635,4.042 0.302,0.188 10 false I12 5.854,2.135 6.115,2.354 0.26,0.219 10 false 3A 2.135,2.063 2.479,2.323 0.344,0.26 10 false I12 2.135,1.708 2.438,1.969 0.302,0.26 10 false I13 0.896,2.135 1.229,2.417 0.333,0.281 10 false 3D 2.24,0.479 2.469,0.802 0.229,0.323 10 false *1 0.563,2.719 0.854,2.948 0.292,0.229 10 false 3F 0.896,1.51 1.177,1.771 0.281,0.26 10 false 3C 5.865,1.49 6.177,1.74 0.313,0.25 10 false 3B 5.885,5.083 6.135,5.365 0.25,0.281 10 false 3F 4.292,0.781 4.615,1.01 0.323,0.229 10 false MB 0.167,0.156 0.479,0.354 0.313,0.198 10 false *a 1.531,3.229 1.875,3.49 0.344,0.26 10 false *2
*1 Main Body ECU (Multiplex Network Body ECU)) *2 3 connectors
*a Component without harness connected
(Instrument Panel Junction Block Assembly and Main Body ECU (Multiplex Network Body ECU))
- -


a.

Disconnect the cable from the negative (-) auxiliary battery terminal.


b.

Disconnect the main body ECU (multiplex network body ECU) connectors.

C204058C06
1.792,0.542 2.125,0.76 0.333,0.219 2.146,3.594 2.479,3.813 0.333,0.219 4.771,0.573 5.104,0.792 0.333,0.219 2.708,0.75 2.594,0.75 2.594,0.75 2.052,1.677 false 2.771,1.021 2.635,1.021 2.635,1.021 2.146,1.677 false 5.656,0.708 5.531,0.708 5.531,0.708 5.052,1.656 false 5.854,0.99 5.688,0.99 5.688,0.99 5.125,1.656 false 4.771,4.167 4.625,4.167 4.625,4.167 4.292,3.99 false 3.979,2.844 3.729,2.844 3.729,2.844 3.573,3.417 false 0.969,0.417 1.24,0.729 0.271,0.313 10 false *a 1.979,2.802 2.448,3.094 0.469,0.292 10 false *1 4.854,4.073 5.146,4.25 0.292,0.177 10 false BAT 1.875,0.563 2.25,0.865 0.375,0.302 10 false I12 2.229,3.604 2.552,3.823 0.323,0.219 10 false I39 4.854,0.594 5.198,0.865 0.344,0.271 10 false I13 2.75,0.688 3.333,0.99 0.583,0.302 10 false CANP 2.823,0.948 3.396,1.24 0.573,0.292 10 false CANN 5.698,0.625 6.281,0.885 0.583,0.26 10 false CANL 5.906,0.906 6.479,1.26 0.573,0.354 10 false CANH 4.031,2.792 4.438,2.969 0.406,0.177 10 false CG
*1 DLC3 - -
*a Front view of wire harness connector
(to Main Body ECU (Multiplex Network Body ECU))
- -



c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
V Bus Branch Lines
Terminal No. (Symbol) Wiring Color Terminal Description Condition Specified Condition
I13-14 (CANH) - I13-13 (CANL) P - W HIGH-level CAN bus line - LOW-level CAN bus line Cable disconnected from negative (-) auxiliary battery terminal 54 to 69 Ω
I13-14 (CANH) - I39-4 (CG) P - W-B HIGH-level CAN bus line - Ground Cable disconnected from negative (-) auxiliary battery terminal 200 Ω or higher
I13-13 (CANL) - I39-4 (CG) W - W-B LOW-level CAN bus line - Ground Cable disconnected from negative (-) auxiliary battery terminal 200 Ω or higher
I13-14 (CANH) - I39-16 (BAT) P - R HIGH-level CAN bus line - Auxiliary battery positive (+) Cable disconnected from negative (-) auxiliary battery terminal 6 kΩ or higher
I13-13 (CANL) - I39-16 (BAT) W - R LOW-level CAN bus line - Auxiliary battery positive (+) Cable disconnected from negative (-) auxiliary battery terminal 6 kΩ or higher

Sub Bus 1 Main Lines
Terminal No. (Symbol) Wiring Color Terminal Description Condition Specified Condition
I12-9 (CANP) - I12-10 (CANN) R - GR HIGH-level CAN bus line - LOW-level CAN bus line Cable disconnected from negative (-) auxiliary battery terminal 108 to 132 Ω
I12-9 (CANP) - I39-4 (CG) R - W-B HIGH-level CAN bus line - Ground Cable disconnected from negative (-) auxiliary battery terminal 200 Ω or higher
I12-10 (CANN) - I39-4 (CG) GR - W-B LOW-level CAN bus line - Ground Cable disconnected from negative (-) auxiliary battery terminal 200 Ω or higher
I12-9 (CANP) - I39-16 (BAT) R - R HIGH-level CAN bus line - Auxiliary battery positive (+) Cable disconnected from negative (-) auxiliary battery terminal 6 kΩ or higher
I12-10 (CANN) - I39-16 (BAT) GR - R LOW-level CAN bus line - Auxiliary battery positive (+) Cable disconnected from negative (-) auxiliary battery terminal 6 kΩ or higher




BRAKE BOOSTER WITH MASTER CYLINDER ASSEMBLY (SKID CONTROL ECU)


C156569C12
3.406,0.604 3.781,0.833 0.375,0.229 0.25,0.188 0.49,0.365 0.24,0.177 10 false *a 3.458,0.625 3.844,0.896 0.385,0.271 10 false A28
*a Component without harness connected
(Brake Booster with Master Cylinder Assembly (Skid Control ECU))
- -


a.

Disconnect the cable from the negative (-) auxiliary battery terminal.


b.
C249762C39
0.208,0.802 0.625,1.073 0.417,0.271 1.667,2.146 1.063,2.781 false 1.76,2.156 1.563,2.781 false 1.958,2.146 2.073,2.781 false 2.063,2.156 2.573,2.781 false 2.635,2.042 3.104,2.875 false 2.635,1.74 2.927,0.823 false 0.198,0.188 0.385,0.344 0.188,0.156 10 false *a 0.292,0.833 0.771,1.177 0.479,0.344 10 false A28 0.813,2.792 1.229,2.948 0.417,0.156 10 false CA2L 1.323,2.792 1.74,2.948 0.417,0.156 10 false CA2H 1.854,2.792 2.271,2.948 0.417,0.156 10 false CA1H 2.417,2.781 2.833,2.938 0.417,0.156 10 false CA1L 2.969,2.896 3.365,3.104 0.396,0.208 10 false GND 2.875,0.615 3.198,0.896 0.323,0.281 10 false BS
*a Front view of wire harness connector
(Brake Booster with Master Cylinder Assembly (Skid Control ECU))


Disconnect the brake booster with master cylinder assembly (skid control ECU) connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
V Bus Branch Lines
Terminal No. (Symbol) Wiring Color Terminal Description Condition Specified Condition
A28-37 (CA1H) - A28-38 (CA1L) GR - W HIGH-level CAN bus line - LOW-level CAN bus line Cable disconnected from negative (-) auxiliary battery terminal 54 to 69 Ω
A28-37 (CA1H) - A28-28 (GND) GR - W-B HIGH-level CAN bus line - Ground Cable disconnected from negative (-) auxiliary battery terminal 200 Ω or higher
A28-38 (CA1L) - A28-28 (GND) W - W-B LOW-level CAN bus line - Ground Cable disconnected from negative (-) auxiliary battery terminal 200 Ω or higher
A28-37 (CA1H) - A28-15 (BS) GR - Y HIGH-level CAN bus line - Auxiliary battery positive (+) Cable disconnected from negative (-) auxiliary battery terminal 6 kΩ or higher
A28-38 (CA1L) - A28-15 (BS) W - Y LOW-level CAN bus line - Auxiliary battery positive (+) Cable disconnected from negative (-) auxiliary battery terminal 6 kΩ or higher


Standard Resistance:
Sub Bus 15 Branch Lines
Terminal No. (Symbol) Wiring Color Terminal Description Condition Specified Condition
A28-35 (CA2H) - A28-34 (CA2L) B - W HIGH-level CAN bus line - LOW-level CAN bus line Cable disconnected from negative (-) auxiliary battery terminal 54 to 69 Ω
A28-35 (CA2H) - A28-28 (GND) B - W-B HIGH-level CAN bus line - Ground Cable disconnected from negative (-) auxiliary battery terminal 200 Ω or higher
A28-34 (CA2L) - A28-28 (GND) W - W-B LOW-level CAN bus line - Ground Cable disconnected from negative (-) auxiliary battery terminal 200 Ω or higher
A28-35 (CA2H) - A28-15 (BS) B - Y HIGH-level CAN bus line - Auxiliary battery positive (+) Cable disconnected from negative (-) auxiliary battery terminal 6 kΩ or higher
A28-34 (CA2L) - A28-15 (BS) W - Y LOW-level CAN bus line - Auxiliary battery positive (+) Cable disconnected from negative (-) auxiliary battery terminal 6 kΩ or higher




STEERING SENSOR


a.

Disconnect the cable from the negative (-) auxiliary battery terminal.


b.
C156493C42
1.188,0.792 1.677,1.083 0.49,0.292 1.208,3.219 1.521,3.219 1.521,3.219 1.521,2.698 false 0.844,2.99 1.333,2.99 1.333,2.99 1.333,2.708 false 2.021,3.229 1.708,3.229 1.708,3.229 1.708,2.708 false 2.573,2.99 2.083,2.99 2.083,2.99 2.083,2.708 false 0.198,0.146 0.677,0.5 0.479,0.354 10 false *a 0.521,2.917 1,3.156 0.479,0.24 10 false ESS 0.833,3.146 1.375,3.365 0.542,0.219 10 false CANL 2.083,3.146 2.615,3.396 0.531,0.25 10 false CANH 2.615,2.906 3.031,3.146 0.417,0.24 10 false BAT 1.344,0.844 1.698,1.104 0.354,0.26 10 false I30
*a Front view of wire harness connector
(to Steering Sensor)


Disconnect the steering sensor connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Terminal No. (Symbol) Wiring Color Terminal Description Condition Specified Condition
I30-3 (CANH) - I30-2 (CANL) V - W HIGH-level CAN bus line - LOW-level CAN bus line Cable disconnected from negative (-) auxiliary battery terminal 54 to 69 Ω
I30-3 (CANH) - I30-1 (ESS) V - W-B HIGH-level CAN bus line - Ground Cable disconnected from negative (-) auxiliary battery terminal 200 Ω or higher
I30-2 (CANL) - I30-1 (ESS) W - W-B LOW-level CAN bus line - Ground Cable disconnected from negative (-) auxiliary battery terminal 200 Ω or higher
I30-3 (CANH) - I30-5 (BAT) V - W HIGH-level CAN bus line - Auxiliary battery positive (+) Cable disconnected from negative (-) auxiliary battery terminal 6 kΩ or higher
I30-2 (CANL) - I30-5 (BAT) W - W LOW-level CAN bus line - Auxiliary battery positive (+) Cable disconnected from negative (-) auxiliary battery terminal 6 kΩ or higher




POWER STEERING ECU ASSEMBLY


a.

Disconnect the cable from the negative (-) auxiliary battery terminal.


b.

Disconnect the power steering ECU assembly connectors.

C239855C16
3.729,0.198 4.052,0.396 0.323,0.198 5.719,0.198 6.042,0.396 0.323,0.198 3.906,1.844 4.229,2.042 0.323,0.198 4.708,1.844 5.031,2.042 0.323,0.198 5.563,1.844 5.885,2.042 0.323,0.198 1.875,0.833 2.198,1.031 0.323,0.198 0.719,1.313 1.042,1.51 0.323,0.198 1.104,1.313 1.427,1.51 0.323,0.198 1.479,1.313 1.802,1.51 0.323,0.198 0.688,3.469 1.01,3.667 0.323,0.198 0.906,1.313 1.031,1.146 false 1.271,1.313 1.292,1.146 false 1.625,1.313 1.542,1.146 false 2.021,0.833 2.021,0.771 false 1.01,3.521 1.083,3.49 false 3.854,0.198 4.188,0.427 0.333,0.229 10 false j2 5.833,0.198 6.083,0.344 0.25,0.146 10 false c 4.021,1.844 4.281,2.156 0.26,0.313 10 false j3 4.833,1.844 5.073,2.073 0.24,0.229 10 false a 5.698,1.844 5.948,2.094 0.25,0.25 10 false b 0.135,0.115 0.417,0.344 0.281,0.229 10 false *a 1.99,0.833 2.344,1.115 0.354,0.281 10 false j2 0.833,1.313 1.135,1.573 0.302,0.26 10 false j3 1.219,1.313 1.51,1.604 0.292,0.292 10 false a 1.604,1.313 1.979,1.583 0.375,0.271 10 false b 0.823,3.469 1.073,3.615 0.25,0.146 10 false c
*a Component without harness connected
(Power Steering ECU Assembly)
- -


C250526C01
0.708,1.51 1.104,1.75 0.396,0.24 4.708,0.865 5.104,1.104 0.396,0.24 2.104,1.969 2.552,2.25 false 2.104,1.802 2.563,1.448 false 4.083,1.823 4.417,1.823 false 5.406,1.823 5.74,1.823 false 0.125,0.115 0.458,0.438 0.333,0.323 10 false *a 2.615,2.177 3.042,2.354 0.427,0.177 10 false CANL 2.615,1.354 3.073,1.531 0.458,0.177 10 false CANH 3.802,1.75 4.271,2.031 0.469,0.281 10 false PIG 5.792,1.76 6.344,2.042 0.552,0.281 10 false PGND 0.844,1.531 1.208,1.833 0.365,0.302 10 false j3 4.854,0.896 5.083,1.135 0.229,0.24 10 false j2
*a Front view of wire harness connector
(to Power Steering ECU Assembly)
- -



c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Terminal No. (Symbol) Wiring Color Terminal Description Condition Specified Condition
j3-4 (CANH) - j3-8 (CANL) Y - SB HIGH-level CAN bus line - LOW-level CAN bus line Cable disconnected from negative (-) auxiliary battery terminal 54 to 69 Ω
j3-4 (CANH) - j2-2 (PGND) Y - B HIGH-level CAN bus line - Ground Cable disconnected from negative (-) auxiliary battery terminal 200 Ω or higher
j3-8 (CANL) - j2-2 (PGND) SB - B LOW-level CAN bus line - Ground Cable disconnected from negative (-) auxiliary battery terminal 200 Ω or higher
j3-4 (CANH) - j2-1 (PIG) Y - R HIGH-level CAN bus line - Auxiliary battery positive (+) Cable disconnected from negative (-) auxiliary battery terminal 6 kΩ or higher
j3-8 (CANL) - j2-1 (PIG) SB - R LOW-level CAN bus line - Auxiliary battery positive (+) Cable disconnected from negative (-) auxiliary battery terminal 6 kΩ or higher




AIRBAG SENSOR ASSEMBLY


a.

Disconnect the cable from the negative (-) auxiliary battery terminal.


b.

Disconnect the airbag sensor assembly connector.

C188802C14
0.552,1.552 0.927,1.76 0.375,0.208 3.323,1.594 3.698,1.802 0.375,0.208 1.25,1.177 1.51,1.615 false 1.417,1.885 1.219,2.313 false 1.698,1.875 1.615,2.229 false 5.76,1.958 5.938,2.302 false 0.188,0.146 2.583,0.5 2.396,0.354 10 false *a 1.042,2.344 1.521,2.615 0.479,0.271 10 false CANL 1.031,1.01 1.521,1.208 0.49,0.198 10 false CANH 1.552,2.26 1.875,2.5 0.323,0.24 10 false E1 5.854,2.323 6.208,2.49 0.354,0.167 10 false BAT 0.646,1.573 1.094,1.865 0.448,0.292 10 false I47 3.396,0.156 3.844,0.438 0.448,0.281 10 false *1 3.427,1.625 3.854,1.896 0.427,0.271 10 false I39
*1 DLC3 - -
*a Front view of wire harness connector
(to Airbag Sensor Assembly)
- -



c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Terminal No. (Symbol) Wiring Color Terminal Description Condition Specified Condition
I47-13 (CANH) - I47-22 (CANL) Y - W HIGH-level CAN bus line - LOW-level CAN bus line Cable disconnected from negative (-) auxiliary battery terminal 54 to 69 Ω
I47-13 (CANH) - I47-25 (E1) Y - W-B HIGH-level CAN bus line - Ground Cable disconnected from negative (-) auxiliary battery terminal 200 Ω or higher
I47-22 (CANL) - I47-25 (E1) W - W-B LOW-level CAN bus line - Ground Cable disconnected from negative (-) auxiliary battery terminal 200 Ω or higher
I47-13 (CANH) - I39-16 (BAT) Y - R HIGH-level CAN bus line - Auxiliary battery positive (+) Cable disconnected from negative (-) auxiliary battery terminal 6 kΩ or higher
I47-22 (CANL) - I39-16 (BAT) W - R LOW-level CAN bus line - Auxiliary battery positive (+) Cable disconnected from negative (-) auxiliary battery terminal 6 kΩ or higher




SMART KEY ECU ASSEMBLY (CERTIFICATION ECU)


C244122C02
1.677,1.625 2.094,1.885 0.417,0.26 3.406,1.625 3.823,1.885 0.417,0.26 4.865,1.615 5.281,1.875 0.417,0.26 1.781,1.677 2.021,1.875 0.24,0.198 10 false O2 0.094,0.094 0.406,0.385 0.313,0.292 10 false *a 3.521,1.677 3.76,1.875 0.24,0.198 10 false I87 4.969,1.667 5.208,1.865 0.24,0.198 10 false I86
*a Component without harness connected
(Smart Key ECU Assembly (Certification ECU))
- -


a.

Disconnect the cable from the negative (-) auxiliary battery terminal.


b.

Disconnect the smart key ECU assembly (certification ECU) connector.

C250527C02
1.542,2.156 1.927,2.375 0.385,0.219 5.365,2.156 5.75,2.375 0.385,0.219 0.979,0.99 1.042,0.99 1.042,0.99 1.042,1.635 false 4.781,1.01 4.844,1.01 4.844,1.01 4.844,1.656 false 1.229,0.99 1.167,0.99 1.167,0.99 1.167,1.625 false 2.469,0.99 2.406,0.99 2.406,0.99 2.406,1.625 false 0.104,0.073 0.354,0.281 0.25,0.208 10 false *a 0.573,0.927 1.146,1.188 0.573,0.26 10 false CANH 1.646,2.198 2.094,2.583 0.448,0.385 10 false I87 1.302,0.917 1.844,1.135 0.542,0.219 10 false CANL 4.646,0.948 4.958,1.135 0.313,0.188 10 false E 2.531,0.917 2.979,1.073 0.448,0.156 10 false +B 5.479,2.198 5.865,2.469 0.385,0.271 10 false I86
*a Front view of wire harness connector
(to Smart Key ECU Assembly (Certification ECU))
- -



c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Terminal No. (Symbol) Wiring Color Terminal Description Condition Specified Condition
I87-1 (CANH) - I87-2 (CANL) L - W HIGH-level CAN bus line - LOW-level CAN bus line Cable disconnected from negative (-) auxiliary battery terminal 54 to 69 Ω
I87-1 (CANH) - I86-1 (E) L - W-B HIGH-level CAN bus line - Ground Cable disconnected from negative (-) auxiliary battery terminal 200 Ω or higher
I87-2 (CANL) - I86-1 (E) W - W-B LOW-level CAN bus line - Ground Cable disconnected from negative (-) auxiliary battery terminal 200 Ω or higher
I87-1 (CANH) - I87-5 (+B) L - SB HIGH-level CAN bus line - Auxiliary battery positive (+) Cable disconnected from negative (-) auxiliary battery terminal 6 kΩ or higher
I87-2 (CANL) - I87-5 (+B) W - SB LOW-level CAN bus line - Auxiliary battery positive (+) Cable disconnected from negative (-) auxiliary battery terminal 6 kΩ or higher




RADIO AND DISPLAY RECEIVER ASSEMBLY (for Radio and Display Type)


E225865C06
1.448,0.083 1.823,0.313 0.375,0.229 2.323,0.083 2.698,0.313 0.375,0.229 1.208,1.365 1.583,1.594 0.375,0.229 5,0.042 5.375,0.271 0.375,0.229 3.417,1.375 3.792,1.604 0.375,0.229 5.594,1.26 5.969,1.49 0.375,0.229 1.5,0.125 1.854,0.396 0.354,0.271 10 false I152 2.375,0.125 2.802,0.469 0.427,0.344 10 false I153 1.271,1.417 1.74,1.708 0.469,0.292 10 false I154 5.052,0.083 5.521,0.365 0.469,0.281 10 false I155 3.458,1.417 3.948,1.656 0.49,0.24 10 false I156 5.688,1.302 6.073,1.573 0.385,0.271 10 false RA 0.094,0.104 0.406,0.385 0.313,0.281 10 false *a
*a Component without harness connected
(Radio and Display Receiver Assembly)
- -


a.

Disconnect the cable from the negative (-) auxiliary battery terminal.


b.

Disconnect the radio and display receiver assembly connectors.

C240506C17
0.604,1.448 1,1.688 0.396,0.24 3.875,1.448 4.271,1.688 0.396,0.24 1.844,0.552 2,0.552 2,0.552 2,1.688 false 2.333,0.552 2.115,0.552 2.115,0.552 2.115,1.688 false 5.781,0.531 5.625,0.531 5.625,0.531 5.625,1.51 false 5.177,2.292 5.01,2.292 5.01,2.292 5.01,1.896 false 0.135,0.052 0.313,0.229 0.177,0.177 10 false *a 2.417,0.49 3.073,0.802 0.656,0.313 10 false CANL 1.427,0.479 2.073,0.813 0.646,0.333 10 false CANH 5.865,0.448 6.25,0.74 0.385,0.292 10 false +B1 5.229,2.219 5.823,2.51 0.594,0.292 10 false GND1 0.656,1.49 1.021,1.75 0.365,0.26 10 false I155 3.948,1.49 4.406,1.792 0.458,0.302 10 false I152
*a Front view of wire harness connector
(to Radio and Display Receiver Assembly)
- -



c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Terminal No. (Symbol) Wiring Color Terminal Description Condition Specified Condition
I155-9 (CANH) - I155-10 (CANL) R - W HIGH-level CAN bus line - LOW-level CAN bus line Cable disconnected from negative (-) auxiliary battery terminal 54 to 69 Ω
I155-9 (CANH) - I152-7 (GND1) R - BR HIGH-level CAN bus line - Ground Cable disconnected from negative (-) auxiliary battery terminal 200 Ω or higher
I155-10 (CANL) - I152-7 (GND1) W - BR LOW-level CAN bus line - Ground Cable disconnected from negative (-) auxiliary battery terminal 200 Ω or higher
I155-9 (CANH) - I152-4 (+B1) R - L-Y HIGH-level CAN bus line - Auxiliary battery positive (+) Cable disconnected from negative (-) auxiliary battery terminal 6 kΩ or higher
I155-10 (CANL) - I152-4 (+B1) W - L-Y LOW-level CAN bus line - Auxiliary battery positive (+) Cable disconnected from negative (-) auxiliary battery terminal 6 kΩ or higher




NAVIGATION ECU SUB-ASSEMBLY (for Navigation Receiver Type)


E225865C07
1.448,0.156 1.823,0.385 0.375,0.229 2.323,0.156 2.698,0.385 0.375,0.229 1.208,1.448 1.583,1.677 0.375,0.229 5,0.115 5.375,0.344 0.375,0.229 3.417,1.458 3.792,1.688 0.375,0.229 5.594,1.344 5.969,1.573 0.375,0.229 1.531,0.198 1.854,0.365 0.323,0.167 10 false I64 2.427,0.188 2.75,0.354 0.323,0.167 10 false I65 1.302,1.49 1.625,1.656 0.323,0.167 10 false I66 5.094,0.146 5.354,0.354 0.26,0.208 10 false I67 3.479,1.49 3.906,1.729 0.427,0.24 10 false I147 5.688,1.375 6.042,1.625 0.354,0.25 10 false RA 0.104,0.094 0.427,0.375 0.323,0.281 10 false *a
*a Component without harness connected
(Navigation ECU Sub-assembly)
- -


a.

Disconnect the cable from the negative (-) auxiliary battery terminal.


b.

Disconnect the navigation ECU sub-assembly connectors.

C240506C20
0.594,1.49 0.99,1.729 0.396,0.24 3.875,1.479 4.271,1.719 0.396,0.24 1.885,0.552 2.042,0.552 2.042,0.552 2.042,1.688 false 2.354,0.552 2.135,0.552 2.135,0.552 2.135,1.688 false 5.813,0.531 5.656,0.531 5.656,0.531 5.656,1.51 false 5.125,2.302 4.958,2.302 4.958,2.302 4.958,1.906 false 0.125,0.125 0.448,0.469 0.323,0.344 10 false *a 2.448,0.49 2.979,0.708 0.531,0.219 10 false CANL 1.479,0.479 2.042,0.729 0.563,0.25 10 false CANH 5.885,0.448 6.26,0.708 0.375,0.26 10 false +B1 5.198,2.229 5.646,2.417 0.448,0.188 10 false GND1 0.708,1.531 1.063,1.854 0.354,0.323 10 false I67 3.979,1.521 4.333,1.792 0.354,0.271 10 false I64
*a Front view of wire harness connector
(to Navigation ECU Sub-assembly)
- -



c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Terminal No. (Symbol) Wiring Color Terminal Description Condition Specified Condition
I67-9 (CANH) - I67-10 (CANL) R - W HIGH-level CAN bus line - LOW-level CAN bus line Cable disconnected from negative (-) auxiliary battery terminal 54 to 69 Ω
I67-9 (CANH) - I64-7 (GND1) R - BR HIGH-level CAN bus line - Ground Cable disconnected from negative (-) auxiliary battery terminal 200 Ω or higher
I67-10 (CANL) - I64-7 (GND1) W - BR LOW-level CAN bus line - Ground Cable disconnected from negative (-) auxiliary battery terminal 200 Ω or higher
I67-9 (CANH) - I64-4 (+B1) R - L-Y HIGH-level CAN bus line - Auxiliary battery positive (+) Cable disconnected from negative (-) auxiliary battery terminal 6 kΩ or higher
I67-10 (CANL) - I64-4 (+B1) W - L-Y LOW-level CAN bus line - Auxiliary battery positive (+) Cable disconnected from negative (-) auxiliary battery terminal 6 kΩ or higher




AIR CONDITIONING AMPLIFIER ASSEMBLY


a.

Disconnect the cable from the negative (-) auxiliary battery terminal.


b.

Disconnect the air conditioning amplifier assembly connector.

E226604C18
2.958,0.115 3.292,0.344 0.333,0.229 5.083,0.115 5.417,0.344 0.333,0.229 5.188,0.156 5.49,0.385 0.302,0.229 10 false z1 3.031,0.156 3.344,0.313 0.313,0.156 10 false I77 0.104,0.094 0.427,0.313 0.323,0.219 10 false *a
*a Component without harness connected
(Air Conditioning Amplifier Assembly)
- -


C188799C10
1.75,1.75 2.146,1.948 0.396,0.198 3.625,1.938 3.042,1.052 false 3.729,1.938 4.313,1.052 false 2.677,2.146 2.396,2.51 false 4.271,2.5 3.917,2.01 false 0.219,0.177 0.656,0.521 0.438,0.344 10 false *a 4.167,0.875 4.615,1.042 0.448,0.167 10 false CANL 2.833,0.896 3.281,1.063 0.448,0.167 10 false CANH 2.323,2.51 2.5,2.677 0.177,0.167 10 false B 4.156,2.521 4.583,2.688 0.427,0.167 10 false GND 1.854,1.771 2.177,1.948 0.323,0.177 10 false I77
*a Front view of wire harness connector
(to Air Conditioning Amplifier Assembly)
- -



c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Terminal No. (Symbol) Wiring Color Terminal Description Condition Specified Condition
I77-11 (CANH) - I77-12 (CANL) V - W HIGH-level CAN bus line - LOW-level CAN bus line Cable disconnected from negative (-) auxiliary battery terminal 54 to 69 Ω
I77-11 (CANH) - I77-14 (GND) V - W-B HIGH-level CAN bus line - Ground Cable disconnected from negative (-) auxiliary battery terminal 200 Ω or higher
I77-12 (CANL) - I77-14 (GND) W - W-B LOW-level CAN bus line - Ground Cable disconnected from negative (-) auxiliary battery terminal 200 Ω or higher
I77-11 (CANH) - I77-21 (B) V - Y HIGH-level CAN bus line - Auxiliary battery positive (+) Cable disconnected from negative (-) auxiliary battery terminal 6 kΩ or higher
I77-12 (CANL) - I77-21 (B) W - Y LOW-level CAN bus line - Auxiliary battery positive (+) Cable disconnected from negative (-) auxiliary battery terminal 6 kΩ or higher




OUTER MIRROR CONTROL ECU ASSEMBLY (for Driver Side) (w/ Seat Position Memory System)


B209687C18
2.939,0.247 3.218,0.448 0.278,0.200 10 z17 2.891,0.218 3.217,0.425 0.326,0.207 4.096,0.255 4.346,0.477 0.251,0.222 10 J13 4.044,0.225 4.37,0.432 0.326,0.207 0.119,0.014 0.735,0.440 0.616,0.427 10 *a
*a Component without harness connected
(Outer Mirror Control ECU Assembly (for Driver Side))
- -


a.

Disconnect the cable from the negative (-) auxiliary battery terminal.


b.
C204179C35
1.51,0.25 1.896,0.458 0.385,0.208 0.948,1.823 1.24,1.438 false 1.385,1.438 1.542,1.865 false 2.177,1.135 2.552,1.135 false 2.531,0.615 2.271,0.615 2.271,0.615 1.948,1.135 false 0.083,0.094 0.51,0.385 0.427,0.292 10 false *a 1.396,1.896 1.802,2.073 0.406,0.177 10 false CANP 0.76,1.844 1.25,2.083 0.49,0.24 10 false CANN 2.604,1.063 3.01,1.302 0.406,0.24 10 false GND 2.583,0.552 3.063,0.823 0.479,0.271 10 false CPUB 1.583,0.281 1.938,0.552 0.354,0.271 10 false J13
*a Front view of wire harness connector
(to Outer Mirror Control ECU Assembly (for Driver Side))


Disconnect the outer mirror control ECU assembly connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Terminal No. (Symbol) Wiring Color Terminal Description Condition Specified Condition
J13-9 (CANP) - J13-8 (CANN) P - GR HIGH-level CAN bus line - LOW-level CAN bus line Cable disconnected from negative (-) auxiliary battery terminal 54 to 69 Ω
J13-9 (CANP) - J13-7 (GND) P - W-B HIGH-level CAN bus line - Ground Cable disconnected from negative (-) auxiliary battery terminal 200 Ω or higher
J13-8 (CANN) - J13-7 (GND) GR - W-B LOW-level CAN bus line - Ground Cable disconnected from negative (-) auxiliary battery terminal 200 Ω or higher
J13-9 (CANP) - J13-6 (CPUB) P - W HIGH-level CAN bus line - Auxiliary battery positive (+) Cable disconnected from negative (-) auxiliary battery terminal 6 kΩ or higher
J13-8 (CANN) - J13-6 (CPUB) GR - W LOW-level CAN bus line - Auxiliary battery positive (+) Cable disconnected from negative (-) auxiliary battery terminal 6 kΩ or higher




OUTER MIRROR CONTROL ECU ASSEMBLY (for Front Passenger Side) (w/ Seat Position Memory System)


B209687C19
2.854,0.219 3.177,0.427 0.323,0.208 4,0.229 4.323,0.438 0.323,0.208 2.896,0.25 3.188,0.458 0.292,0.208 10 false z16 4.031,0.25 4.313,0.469 0.281,0.219 10 false K12 0.094,0.073 0.448,0.354 0.354,0.281 10 false *a
*a Component without harness connected
(Outer Mirror Control ECU Assembly (for Front Passenger Side))
- -


a.

Disconnect the cable from the negative (-) auxiliary battery terminal.


b.
C204179C36
1.5,0.25 1.906,0.469 0.406,0.219 0.948,1.823 1.24,1.438 false 1.375,1.438 1.531,1.865 false 2.188,1.156 2.563,1.156 false 2.521,0.604 2.271,0.604 2.271,0.604 1.948,1.125 false 0.104,0.083 0.531,0.375 0.427,0.292 10 false *a 1.375,1.875 1.854,2.115 0.479,0.24 10 false CANP 0.75,1.833 1.229,2.073 0.479,0.24 10 false CANN 2.615,1.073 3.021,1.344 0.406,0.271 10 false GND 2.573,0.531 3.031,0.792 0.458,0.26 10 false CPUB 1.583,0.281 1.99,0.531 0.406,0.25 10 false K12
*a Front view of wire harness connector
(to Outer Mirror Control ECU Assembly (for Front Passenger Side))


Disconnect the outer mirror control ECU assembly connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Terminal No. (Symbol) Wiring Color Terminal Description Condition Specified Condition
K12-9 (CANP) - K12-8 (CANN) G - GR HIGH-level CAN bus line - LOW-level CAN bus line Cable disconnected from negative (-) auxiliary battery terminal 54 to 69 Ω
K12-9 (CANP) - K12-7 (GND) G - W-B HIGH-level CAN bus line - Ground Cable disconnected from negative (-) auxiliary battery terminal 200 Ω or higher
K12-8 (CANN) - K12-7 (GND) GR - W-B LOW-level CAN bus line - Ground Cable disconnected from negative (-) auxiliary battery terminal 200 Ω or higher
K12-9 (CANP) - K12-6 (CPUB) G - W HIGH-level CAN bus line - Auxiliary battery positive (+) Cable disconnected from negative (-) auxiliary battery terminal 6 kΩ or higher
K12-8 (CANN) - K12-6 (CPUB) GR - W LOW-level CAN bus line - Auxiliary battery positive (+) Cable disconnected from negative (-) auxiliary battery terminal 6 kΩ or higher




POSITION CONTROL ECU AND SWITCH ASSEMBLY (for Driver Side) (w/ Seat Position Memory System)


B219505C04
2.802,0.083 3.135,0.281 0.333,0.198 3.688,0.083 4.021,0.281 0.333,0.198 3.75,0.115 4.313,0.365 0.563,0.25 10 false d11 2.854,0.115 3.438,0.375 0.583,0.26 10 false d12 0.104,0.115 0.823,0.708 0.719,0.594 10 false *a
*a Component without harness connected
(Position Control ECU and Switch Assembly (for Driver Side))
- -


a.

Disconnect the cable from the negative (-) auxiliary battery terminal.


b.

Disconnect the connectors of the position control ECU and switch assembly.

C204065C08
1.958,0.573 2.302,0.781 0.344,0.208 4.854,0.438 5.219,0.656 0.365,0.219 5.01,2.5 4.781,2.146 false 4.323,2.469 4.646,2.135 false 1.427,2.417 1.823,2.083 false 1.427,1.354 1.813,1.792 false 0.104,0.115 0.75,0.406 0.646,0.292 10 false *a 2.031,0.594 2.323,0.823 0.292,0.229 10 false d11 4.927,0.479 5.25,0.656 0.323,0.177 10 false d12 4.854,2.531 5.344,2.708 0.49,0.177 10 false CANP 4.125,2.479 4.625,2.656 0.5,0.177 10 false CANN 1.094,1.26 1.552,1.552 0.458,0.292 10 false GND 1.229,2.417 1.552,2.604 0.323,0.188 10 false +B
*a Front view of wire harness connector
(to Position Control ECU and Switch Assembly (for Driver Side))
- -



c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Terminal No. (Symbol) Wiring Color Terminal Description Condition Specified Condition
d12-8 (CANP) - d12-7 (CANN) L - W HIGH-level CAN bus line - LOW-level CAN bus line Cable disconnected from negative (-) auxiliary battery terminal 54 to 69 Ω
d12-8 (CANP) - d11-2 (GND) L - W-B HIGH-level CAN bus line - Ground Cable disconnected from negative (-) auxiliary battery terminal 200 Ω or higher
d12-7 (CANN) - d11-2 (GND) W - W-B LOW-level CAN bus line - Ground Cable disconnected from negative (-) auxiliary battery terminal 200 Ω or higher
d12-8 (CANP) - d11-7 (+B) L - W HIGH-level CAN bus line - Auxiliary battery positive (+) Cable disconnected from negative (-) auxiliary battery terminal 6 kΩ or higher
d12-7 (CANN) - d11-7 (+B) W - W LOW-level CAN bus line - Auxiliary battery positive (+) Cable disconnected from negative (-) auxiliary battery terminal 6 kΩ or higher




BLIND SPOT MONITOR SENSOR LH (w/ Blind Spot Monitor System)


E211805C05
2.323,0.771 2.75,1.031 0.427,0.26 2.427,0.823 2.781,1 0.354,0.177 10 false T10 0.083,0.073 0.354,0.344 0.271,0.271 10 false *a
*a Component without harness connected
(Blind Spot Monitor Sensor LH)
- -


a.

Disconnect the cable from the negative (-) auxiliary battery terminal.


b.

Disconnect the blind spot monitor sensor LH connector.

C240489C05
0.885,1.615 1.313,1.865 0.427,0.25 3.583,1.604 4.01,1.854 0.427,0.25 2.438,0.979 2.25,0.979 2.25,0.979 2.25,1.74 false 2.438,2.344 2.26,2.344 2.26,2.344 2.26,1.906 false 5.927,2.375 5.708,2.375 5.708,2.375 5.708,1.969 false 1.469,0.99 1.802,0.99 1.802,0.99 1.802,1.74 false 0.208,0.135 0.406,0.333 0.198,0.198 10 false *a 5.958,2.292 6.365,2.521 0.406,0.229 10 false BAT 2.521,0.896 3.021,1.198 0.5,0.302 10 false CA1N 2.49,2.25 3.021,2.521 0.531,0.271 10 false CA1P 1.021,0.906 1.646,1.198 0.625,0.292 10 false BLGD 3.469,0.135 3.667,0.333 0.198,0.198 10 false *1 0.979,1.656 1.375,1.833 0.396,0.177 10 false T10 3.708,1.656 4.031,1.833 0.323,0.177 10 false I39
*1 DLC3 - -
*a Front view of wire harness connector
(to Blind Spot Monitor Sensor LH)
- -



c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Terminal No. (Symbol) Wiring Color Terminal Description Condition Specified Condition
T10-8 (CA1P) - T10-4 (CA1N) R - B HIGH-level CAN bus line - LOW-level CAN bus line Cable disconnected from negative (-) auxiliary battery terminal 54 to 69 Ω
T10-8 (CA1P) - T10-1 (BLGD) R - BR HIGH-level CAN bus line - Ground Cable disconnected from negative (-) auxiliary battery terminal 200 Ω or higher
T10-4 (CA1N) - T10-1 (BLGD) B - BR LOW-level CAN bus line - Ground Cable disconnected from negative (-) auxiliary battery terminal 200 Ω or higher
T10-8 (CA1P) - I39-16 (BAT) R - R HIGH-level CAN bus line - Auxiliary battery positive (+) Cable disconnected from negative (-) auxiliary battery terminal 6 kΩ or higher
T10-4 (CA1N) - I39-16 (BAT) B - R LOW-level CAN bus line - Auxiliary battery positive (+) Cable disconnected from negative (-) auxiliary battery terminal 6 kΩ or higher




BLIND SPOT MONITOR SENSOR RH (w/ Blind Spot Monitor System)


E211805C04
2.323,0.75 2.792,1.031 0.469,0.281 2.417,0.813 2.792,0.99 0.375,0.177 10 false O28 0.104,0.115 0.406,0.448 0.302,0.333 10 false *a
*a Component without harness connected
(Blind Spot Monitor Sensor RH)
- -


a.

Disconnect the cable from the negative (-) auxiliary battery terminal.


b.

Disconnect the blind spot monitor sensor RH connector.

C240489C04
0.906,1.635 1.323,1.875 0.417,0.24 3.667,1.615 4.042,1.844 0.375,0.229 2.406,0.958 2.219,0.958 2.219,0.958 2.219,1.719 false 2.396,2.375 2.219,2.375 2.219,2.375 2.219,1.938 false 5.917,2.375 5.698,2.375 5.698,2.375 5.698,1.969 false 1.5,0.969 1.833,0.969 1.833,0.969 1.833,1.719 false 0.167,0.146 0.469,0.396 0.302,0.25 10 false *a 5.969,2.313 6.375,2.531 0.406,0.219 10 false BAT 2.458,0.896 2.885,1.094 0.427,0.198 10 false CA1N 2.438,2.302 2.865,2.5 0.427,0.198 10 false CA1P 1.094,0.896 1.646,1.146 0.552,0.25 10 false BRGD 0.979,1.677 1.396,1.938 0.417,0.26 10 false O28 3.76,1.656 4.104,1.896 0.344,0.24 10 false I39 3.375,0.135 3.667,0.427 0.292,0.292 10 false *1
*1 DLC3 - -
*a Front view of wire harness connector
(to Blind Spot Monitor Sensor RH)
- -



c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Terminal No. (Symbol) Wiring Color Terminal Description Condition Specified Condition
O28-8 (CA1P) - O28-4 (CA1N) R - B HIGH-level CAN bus line - LOW-level CAN bus line Cable disconnected from negative (-) auxiliary battery terminal 54 to 69 Ω
O28-8 (CA1P) - O28-1 (BRGD) R - BR HIGH-level CAN bus line - Ground Cable disconnected from negative (-) auxiliary battery terminal 200 Ω or higher
O28-4 (CA1N) - O28-1 (BRGD) B - BR LOW-level CAN bus line - Ground Cable disconnected from negative (-) auxiliary battery terminal 200 Ω or higher
O28-8 (CA1P) - I39-16 (BAT) R - R HIGH-level CAN bus line - Auxiliary battery positive (+) Cable disconnected from negative (-) auxiliary battery terminal 6 kΩ or higher
O28-4 (CA1N) - I39-16 (BAT) B - R LOW-level CAN bus line - Auxiliary battery positive (+) Cable disconnected from negative (-) auxiliary battery terminal 6 kΩ or higher




HEADLIGHT SWIVEL ECU ASSEMBLY (AFS ECU) (w/ Automatic High Beam System)


C188112C02
0.458,1.563 0.802,1.771 0.344,0.208 0.167,0.146 0.469,0.521 0.302,0.375 10 false *a 0.5,1.594 0.917,1.885 0.417,0.292 10 false A35
*a Component without harness connected
(Headlight Swivel ECU Assembly (AFS ECU))
- -


a.

Disconnect the cable from the negative (-) auxiliary battery terminal.


b.

Disconnect the headlight swivel ECU assembly (AFS ECU) connector.

C188932C02
0.25,1.594 0.604,1.802 0.354,0.208 3.667,1.583 4.021,1.792 0.354,0.208 1.927,1.844 1.708,2.344 false 3.167,1.688 3.417,2.354 false 5.896,1.969 6.104,2.365 false 3.042,1.698 2.802,2.365 false 3.24,2.438 3.823,2.677 0.583,0.24 10 false MPX2 2.594,2.406 3.125,2.667 0.531,0.26 10 false MPX1 1.594,2.375 1.938,2.583 0.344,0.208 10 false E1 5.979,2.406 6.333,2.573 0.354,0.167 10 false BAT 0.302,1.625 0.625,1.802 0.323,0.177 10 false A35 3.531,0.167 4.031,0.333 0.5,0.167 10 false *1 0.219,0.167 0.49,0.521 0.271,0.354 10 false *a 3.74,1.615 4.063,1.792 0.323,0.177 10 false I39
*1 DLC3 - -
*a Front view of wire harness connector
(to Headlight Swivel ECU Assembly (AFS ECU))
- -



c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Terminal No. (Symbol) Wiring Color Terminal Description Condition Specified Condition
A35-12 (MPX1) - A35-13 (MPX2) B - W HIGH-level CAN bus line - LOW-level CAN bus line Cable disconnected from negative (-) auxiliary battery terminal 54 to 69 Ω
A35-12 (MPX1) - A35-22 (E1) B - W-B HIGH-level CAN bus line - Ground Cable disconnected from negative (-) auxiliary battery terminal 200 Ω or higher
A35-13 (MPX2) - A35-22 (E1) W - W-B LOW-level CAN bus line - Ground Cable disconnected from negative (-) auxiliary battery terminal 200 Ω or higher
A35-12 (MPX1) - I39-16 (BAT) B - R HIGH-level CAN bus line - Battery positive (+) Cable disconnected from negative (-) auxiliary battery terminal 6 kΩ or higher
A35-13 (MPX2) - I39-16 (BAT) W - R LOW-level CAN bus line - Battery positive (+) Cable disconnected from negative (-) auxiliary battery terminal 6 kΩ or higher