Home › Vehicle Interior › THEFT DETERRENT / KEYLESS ENTRY › SMART ENTRY AND START SYSTEM(for Entry Function)
RM2040EQ _58 Vehicle Interior _014723 THEFT DETERRENT / KEYLESS ENTRY _0075053 SMART ENTRY AND START SYSTEM(for Entry Function) C

THEFT DETERRENT / KEYLESS ENTRY  SMART ENTRY AND START SYSTEM(for Entry Function)  B27A5  Open in Front Floor Electrical Key Oscillator Circuit  


DESCRIPTION

The certification ECU (smart key ECU assembly) generates a request signal and transmits the signal to the No. 1 indoor electrical key antenna assembly (front floor). For the No. 1 indoor electrical key antenna assembly (front floor) to detect when the electrical key transmitter sub-assembly is inside the vehicle, the signal from the certification ECU (smart key ECU assembly) requesting a response from the electrical key transmitter sub-assembly is transmitted inside the vehicle. DTC B27A5 is stored by the certification ECU (smart key ECU assembly) when an open circuit is detected between the certification ECU (smart key ECU assembly) and No. 1 indoor electrical key antenna assembly (front floor) (between terminals CLG5 and ANTE5, or terminals CG5B and CLGB).

DTC No. Detection Item DTC Detection Condition Trouble Area Note
B27A5 Open in Front Floor Electrical Key Oscillator Circuit An open circuit is detected in the circuit between the certification ECU (smart key ECU assembly) and No. 1 indoor electrical key antenna assembly (front floor) (CLG5 - ANTE5, CG5B - CLGB) (1 trip detection logic*).
·

Wire harness or connector

·

No. 1 indoor electrical key antenna assembly (front floor)

·

Certification ECU (smart key ECU assembly)


DTC Output Confirmation Operation

Any time



*: Only output while a malfunction is present.


Vehicle Condition and Fail-safe Operation when Malfunction Detected
Vehicle Condition when Malfunction Detected Fail-safe Operation when Malfunction Detected
When electrical key transmitter sub-assembly is in front seat area:
·

Power source mode does not change when power switch pressed

·

Electrical key transmitter sub-assembly locked inside vehicle


-

Related Data List and Active Test
DTC Code Data List and Active Test
B27A5 Key diagnostic mode can be used to perform troubleshooting

WIRING DIAGRAM

B274845E76
1.119,0.406 1.584,0.567 0.465,0.160 10 ANTE5 1.186,0.878 1.585,1.038 0.399,0.160 10 CLGB 0.071,1.347 0.348,1.508 0.278,0.160 10 I46 1.669,0.765 1.774,0.924 0.105,0.158 10 3 1.671,0.314 1.776,0.460 0.105,0.145 10 1 5.644,0.406 6.061,0.573 0.416,0.167 10 CLG5 5.644,0.877 6.074,1.033 0.430,0.156 10 CG5B 5.644,1.337 5.822,1.501 0.178,0.164 10 E 5.337,0.239 5.512,0.396 0.175,0.157 10 11 5.337,0.713 5.531,0.879 0.194,0.166 10 10 5.373,1.171 5.568,1.332 0.195,0.162 10 1 5.317,0.412 5.551,0.573 0.234,0.162 10 I86 5.317,0.875 5.551,1.036 0.234,0.162 10 I86 5.317,1.337 5.551,1.499 0.234,0.162 10 I86 5.317,1.854 6.871,2.209 1.553,0.355 10 Certification ECU (Smart Key ECU Assembly) 0.072,1.493 2.082,1.869 2.010,0.375 10 No. 1 Indoor Electrical Key Antenna Assembly (Front Floor)

CAUTION / NOTICE / HINT

NOTICE:
·

The smart entry and start system (for Entry Function) uses a multiplex communication system (LIN communication system) and the CAN communication system. Inspect the communication function by following How to Proceed with Troubleshooting. Troubleshoot the smart entry and start system (for Entry Function) after confirming that the communication systems are functioning properly.

Click hereVehicle Interior>THEFT DETERRENT / KEYLESS ENTRY>SMART ENTRY AND START SYSTEM(for Entry Function)>HOW TO PROCEED WITH TROUBLESHOOTING

·

When using the intelligent tester with the power switch off to troubleshoot:

Connect the intelligent tester to the DLC3 and turn a courtesy light switch on and off at 1.5-second intervals until communication between the intelligent tester and vehicle begins.

·

Before replacing the certification ECU (smart key ECU assembly), refer to the smart entry and start system (for Entry Function) precaution (See page Vehicle Interior>THEFT DETERRENT / KEYLESS ENTRY>SMART ENTRY AND START SYSTEM(for Entry Function)>PRECAUTION).

·

After repair, confirm that no DTCs are output by performing the "DTC Output Confirmation Operation".

·

The No. 1 indoor electrical key antenna assembly (front floor) has an antenna coil between ANTE5 and CLGB terminals.



PROCEDURE

1.CHECK CONNECTOR CONNECTION
a.

Turn the power switch off.


b.

Check that the connectors are properly connected to the certification ECU (smart key ECU assembly) and No. 1 indoor electrical key antenna assembly (front floor).

OK:

Connectors are properly connected.



Result:
Proceed to
OK
NG



OK

2.CHECK HARNESS AND CONNECTOR (CERTIFICATION ECU - NO. 1 INDOOR ELECTRICAL KEY ANTENNA)

NG

CONNECT CONNECTORS PROPERLY

2.CHECK HARNESS AND CONNECTOR (CERTIFICATION ECU - NO. 1 INDOOR ELECTRICAL KEY ANTENNA)
a.

Disconnect the I86 certification ECU (smart key ECU assembly) connector.


b.

Disconnect the I46 No. 1 indoor electrical key antenna assembly (front floor) connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
I86-11 (CLG5) - I46-1 (ANTE5) Always Below 1 Ω
I86-10 (CG5B) - I46-3 (CLGB) Always Below 1 Ω
I86-1 (E) - Body ground Always Below 1 Ω
I86-11 (CLG5) or I46-1 (ANTE5) - Body ground Always 10 kΩ or higher
I86-10 (CG5B) or I46-3 (CLGB) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

3.CHECK CERTIFICATION ECU (SMART KEY ECU ASSEMBLY) (OUTPUT TO NO. 1 INDOOR ELECTRICAL KEY ANTENNA)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

3.CHECK CERTIFICATION ECU (SMART KEY ECU ASSEMBLY) (OUTPUT TO NO. 1 INDOOR ELECTRICAL KEY ANTENNA)
a.

Connect the I86 certification ECU (smart key ECU assembly) connector.

B282005C11
2.26,0.594 2.635,0.823 0.375,0.229 4.875,0.594 5.25,0.823 0.375,0.229 3.688,0.604 4.063,0.833 0.375,0.229 5.073,1.469 4.833,2.063 false 5.615,1.333 5.833,1.792 false 5.188,1.479 5.365,2.042 false 0.781,0.448 1,0.646 0.219,0.198 10 false *a 1.229,2.792 1.448,2.99 0.219,0.198 10 false *1 0.958,3.594 1.323,3.76 0.365,0.167 10 false GND 2.333,4.375 2.552,4.573 0.219,0.198 10 false *c 5.854,1.823 5.99,1.99 0.135,0.167 10 false E 5.198,2.094 5.604,2.26 0.406,0.167 10 false CG5B 4.625,2.094 5.031,2.26 0.406,0.167 10 false CLG5 2.354,0.635 2.646,0.802 0.292,0.167 10 false O2 4.969,0.635 5.24,0.802 0.271,0.167 10 false I86 3.781,0.646 4.073,0.813 0.292,0.167 10 false I87 1.563,4.365 1.781,4.563 0.219,0.198 10 false *b
*1 Waveform - -
*a Component with harness connected
(Certification ECU (smart key ECU assembly))
*b Within approximately 30 seconds from when the door is closed
*c After approximately 30 seconds from when the door is closed - -



b.

Connect the I46 No. 1 indoor electrical key antenna assembly (front floor) connector.


c.

Using an oscilloscope, check the waveform.

OK:
Tester Connection Switch Condition Tool Setting Specified Condition
I86-11 (CLG5) - I86-1 (E) Procedure:
1.

Power switch off

2.

Electrical key transmitter sub-assembly not inside vehicle

3.

Door is open

4.

Door is closed

5.

Within 30 seconds


2 V/DIV., 500 ms/DIV. Pulse generation (See waveform)
I86-10 (CG5B) - I86-1 (E) Procedure:
1.

Power switch off

2.

Electrical key transmitter sub-assembly not inside vehicle

3.

Door is open

4.

Door is closed

5.

Within 30 seconds


2 V/DIV., 500 ms/DIV. Pulse generation (See waveform)



Result:
Proceed to
OK
NG



OK

4.REPLACE NO.1 INDOOR ELECTRICAL KEY ANTENNA ASSEMBLY (FRONT FLOOR)

NG

REPLACE CERTIFICATION ECU (SMART KEY ECU ASSEMBLY)

4.REPLACE NO.1 INDOOR ELECTRICAL KEY ANTENNA ASSEMBLY (FRONT FLOOR)
a.

Temporarily replace the No. 1 indoor electrical key antenna assembly (front floor) with a new or known good one.

Click hereVehicle Interior>THEFT DETERRENT / KEYLESS ENTRY>ELECTRICAL KEY OSCILLATOR(for Front Floor)>REMOVAL


Result:
Proceed to
NEXT



NEXT

5.CLEAR DTC
5.CLEAR DTC
a.

Clear the DTCs.

Click hereVehicle Interior>THEFT DETERRENT / KEYLESS ENTRY>SMART ENTRY AND START SYSTEM(for Entry Function)>DTC CHECK / CLEAR

Body Electrical > Entry&Start > Clear DTCs
50002 125

Result:
Proceed to
NEXT



NEXT

6.CHECK FOR DTC
6.CHECK FOR DTC
a.

Check for DTCs.

Click hereVehicle Interior>THEFT DETERRENT / KEYLESS ENTRY>SMART ENTRY AND START SYSTEM(for Entry Function)>DTC CHECK / CLEAR

Body Electrical > Entry&Start > Trouble Codes
50001 125
OK:

DTC B27A5 is not output.



Result:
Proceed to
OK
NG



OK

END (NO. 1 INDOOR ELECTRICAL KEY ANTENNA ASSEMBLY (FRONT FLOOR) WAS DEFECTIVE)

NG

REPLACE CERTIFICATION ECU (SMART KEY ECU ASSEMBLY)