Home › Vehicle Interior › THEFT DETERRENT / KEYLESS ENTRY › SMART ENTRY AND START SYSTEM(for Entry Function)
RM2040EQ _58 Vehicle Interior _014723 THEFT DETERRENT / KEYLESS ENTRY _0075053 SMART ENTRY AND START SYSTEM(for Entry Function) C

THEFT DETERRENT / KEYLESS ENTRY  SMART ENTRY AND START SYSTEM(for Entry Function)  B27A7  Open in Inside Luggage Compartment Electrical Key Oscillator Circuit  


DESCRIPTION

The certification ECU (smart key ECU assembly) generates a request signal and transmits the signal to the No. 3 indoor electrical key antenna assembly (inside luggage compartment). For the No. 3 indoor electrical key antenna assembly (inside luggage compartment) to detect when the electrical key transmitter sub-assembly is inside the luggage compartment, the signal from the certification ECU (smart key ECU assembly) requesting a response from the electrical key transmitter sub-assembly is transmitted inside the luggage compartment. DTC B27A7 is stored by the certification ECU (smart key ECU assembly) when an open circuit is detected between the certification ECU (smart key ECU assembly) and No. 3 indoor electrical key antenna assembly (inside luggage compartment) (between terminals CLG7 and ANTE7, or terminals CG7B and CLGB).

DTC No. Detection Item DTC Detection Condition Trouble Area Note
B27A7 Open in Inside Luggage Compartment Electrical Key Oscillator Circuit An open circuit is detected in the circuit between the certification ECU (smart key ECU assembly) and No. 3 indoor electrical key antenna assembly (inside luggage compartment) (CLG7 - ANTE7, CG7B - CLGB) (1 trip detection logic*).
·

Wire harness or connector

·

No. 3 indoor electrical key antenna assembly (inside luggage compartment)

·

Certification ECU (smart key ECU assembly)


DTC Output Confirmation Operation

Any time



*: Only output while a malfunction is present.


Vehicle Condition and Fail-safe Operation when Malfunction Detected
Vehicle Condition when Malfunction Detected Fail-safe Operation when Malfunction Detected
When electrical key transmitter sub-assembly is in luggage compartment:
·

Electrical key transmitter sub-assembly becomes locked inside vehicle


-

Related Data List and Active Test
DTC Code Data List and Active Test
B27A7 Key diagnostic mode can be used to perform troubleshooting

WIRING DIAGRAM

B274845
1.094,0.448 1.656,0.604 0.563,0.156 10 false ANTE7 1.156,0.927 1.76,1.208 0.604,0.281 10 false CLGB 0.094,1.375 0.573,1.677 0.479,0.302 10 false N38 1.677,0.802 1.781,0.958 0.104,0.156 10 false 3 1.677,0.344 1.885,0.594 0.208,0.25 10 false 1 5.635,0.438 6.052,0.604 0.417,0.167 10 false CLG7 5.646,0.906 6.073,1.063 0.427,0.156 10 false CG7B 5.646,1.396 5.823,1.563 0.177,0.167 10 false E 5.365,0.271 5.542,0.427 0.177,0.156 10 false 4 5.354,0.729 5.542,0.896 0.188,0.167 10 false 3 5.365,1.177 5.563,1.344 0.198,0.167 10 false 1 5.281,1.833 6.813,2.323 1.531,0.49 10 false Certification ECU (Smart Key ECU Assembly) 0.083,1.531 2.927,1.948 2.844,0.417 10 false No. 3 Indoor Electrical Key Antenna Assembly (Inside Luggage Compartment) 5.313,1.365 5.583,1.521 0.271,0.156 10 false I86 5.313,0.906 5.531,1.063 0.219,0.156 10 false O2 5.313,0.448 5.531,0.604 0.219,0.156 10 false O2

CAUTION / NOTICE / HINT

NOTICE:
·

The smart entry and start system (for Entry Function) uses a multiplex communication system (LIN communication system) and the CAN communication system. Inspect the communication function by following How to Proceed with Troubleshooting. Troubleshoot the smart entry and start system (for Entry Function) after confirming that the communication systems are functioning properly.

Click hereVehicle Interior>THEFT DETERRENT / KEYLESS ENTRY>SMART ENTRY AND START SYSTEM(for Entry Function)>HOW TO PROCEED WITH TROUBLESHOOTING

·

When using the intelligent tester with the power switch off to troubleshoot:

Connect the intelligent tester to the DLC3 and turn a courtesy light switch on and off at 1.5-second intervals until communication between the intelligent tester and vehicle begins.

·

Before replacing the certification ECU (smart key ECU assembly), refer to the smart entry and start system (for Entry Function) precaution (See page Vehicle Interior>THEFT DETERRENT / KEYLESS ENTRY>SMART ENTRY AND START SYSTEM(for Entry Function)>PRECAUTION).

·

After repair, confirm that no DTCs are output by performing the "DTC Output Confirmation Operation".

·

The No. 3 indoor electrical key antenna assembly (inside luggage compartment) has an antenna coil between ANTE7 and CLGB terminals.



PROCEDURE

1.CHECK CONNECTOR CONNECTION
a.

Turn the power switch off.


b.

Check that the connectors are properly connected to the certification ECU (smart key ECU assembly) and No. 3 indoor electrical key antenna assembly (inside luggage compartment).

OK:

Connectors are properly connected.



Result:
Proceed to
OK
NG



OK

2.CHECK HARNESS AND CONNECTOR (CERTIFICATION ECU - NO. 3 INDOOR ELECTRICAL KEY ANTENNA)

NG

CONNECT CONNECTORS PROPERLY

2.CHECK HARNESS AND CONNECTOR (CERTIFICATION ECU - NO. 3 INDOOR ELECTRICAL KEY ANTENNA)
a.

Disconnect the O2 and I86 certification ECU (smart key ECU assembly) connectors.


b.

Disconnect the N38 No. 3 indoor electrical key antenna assembly (inside luggage compartment) connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
O2-4 (CLG7) - N38-1 (ANTE7) Always Below 1 Ω
O2-3 (CG7B) - N38-3 (CLGB) Always Below 1 Ω
I86-1 (E) - Body ground Always Below 1 Ω
O2-4 (CLG7) or N38-1 (ANTE7) - Body ground Always 10 kΩ or higher
O2-3 (CG7B) or N38-3 (CLGB) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

3.CHECK CERTIFICATION ECU (SMART KEY ECU ASSEMBLY) (OUTPUT TO NO. 3 INDOOR ELECTRICAL KEY ANTENNA ASSEMBLY)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

3.CHECK CERTIFICATION ECU (SMART KEY ECU ASSEMBLY) (OUTPUT TO NO. 3 INDOOR ELECTRICAL KEY ANTENNA ASSEMBLY)
a.

Connect the O2 and I86 certification ECU (smart key ECU assembly) connectors.

B282014
2.281,0.552 2.656,0.781 0.375,0.229 4.906,0.552 5.281,0.781 0.375,0.229 3.708,0.563 4.083,0.792 0.375,0.229 2.844,1.344 2.635,2.052 false 5.625,1.365 5.854,1.833 false 2.958,1.344 3.135,2.094 false 0.917,0.354 1.135,0.552 0.219,0.198 10 false *a 1.198,2.708 1.417,2.906 0.219,0.198 10 false *1 0.979,3.552 1.344,3.719 0.365,0.167 10 false GND 2.969,4.365 3.229,4.604 0.26,0.24 10 false *c 2.26,4.365 2.479,4.563 0.219,0.198 10 false *b 5.875,1.813 6.01,1.979 0.135,0.167 10 false E 2.958,2.125 3.365,2.292 0.406,0.167 10 false CG7B 2.406,2.094 2.813,2.26 0.406,0.167 10 false CLG7 2.375,0.594 2.667,0.76 0.292,0.167 10 false O2 4.99,0.594 5.26,0.76 0.271,0.167 10 false I86 3.802,0.604 4.094,0.771 0.292,0.167 10 false I87
*1 Waveform - -
*a Component with harness connected
(Certification ECU (smart key ECU assembly))
*b Before driver door lock sensor touched
*c After driver door lock sensor touched - -



b.

Connect the N38 No. 3 indoor electrical key antenna assembly (inside luggage compartment) connector.


c.

Using an oscilloscope, check the waveform.

OK:
Tester Connection Switch Condition Tool Setting Specified Condition
O2-4 (CLG7) - I86-1 (E) Proceed:
1.

Power switch off

2.

Electrical key transmitter sub-assembly not inside vehicle

3.

All doors closed

4.

Driver door lock sensor not touched → touched


2 V/DIV., 500 ms/DIV. Pulse generation (See waveform)
O2-3 (CG7B) - I86-1 (E) Proceed:
1.

Power switch off

2.

Electrical key transmitter sub-assembly not inside vehicle

3.

All doors closed

4.

Driver door lock sensor not touched → touched


2 V/DIV., 500 ms/DIV. Pulse generation (See waveform)



Result:
Proceed to
OK
NG



OK

4.REPLACE NO.3 INDOOR ELECTRICAL KEY ANTENNA ASSEMBLY (INSIDE LUGGAGE COMOARTMENT)

NG

REPLACE CERTIFICATION ECU (SMART KEY ECU ASSEMBLY)

4.REPLACE NO.3 INDOOR ELECTRICAL KEY ANTENNA ASSEMBLY (INSIDE LUGGAGE COMOARTMENT)
a.

Temporarily replace the No. 3 indoor electrical key antenna assembly (inside luggage compartment) with a new or known good one.

Click hereVehicle Interior>THEFT DETERRENT / KEYLESS ENTRY>ELECTRICAL KEY OSCILLATOR(for Luggage Compartment)>REMOVAL


Result:
Proceed to
NEXT



NEXT

5.CLEAR DTC
5.CLEAR DTC
a.

Clear the DTCs.

Click hereVehicle Interior>THEFT DETERRENT / KEYLESS ENTRY>SMART ENTRY AND START SYSTEM(for Entry Function)>DTC CHECK / CLEAR

Body Electrical > Entry&Start > Clear DTCs
50002 125

Result:
Proceed to
NEXT



NEXT

6.CHECK FOR DTC
6.CHECK FOR DTC
a.

Check for DTCs.

Click hereVehicle Interior>THEFT DETERRENT / KEYLESS ENTRY>SMART ENTRY AND START SYSTEM(for Entry Function)>DTC CHECK / CLEAR

Body Electrical > Entry&Start > Trouble Codes
50001 125
OK:

DTC B27A7 is not output.



Result:
Proceed to
OK
NG



OK

END (NO. 3 INDOOR ELECTRICAL KEY ANTENNA ASSEMBLY (INSIDE LUGGAGE COMPARTMENT) WAS DEFECTIVE)

NG

REPLACE CERTIFICATION ECU (SMART KEY ECU ASSEMBLY)