OUTLINE OF THEFT DETERRENT SYSTEM
The theft deterrent system can be set by locking the doors using the transmitter, smart entry and start system, key or by opening and closing the doors.
The alarm function will be activated when someone attempts to forcibly unlock any of the doors or open any of the doors, engine hood and luggage compartment door while the system is in the armed state.
In the alarm sounding state, the system blinks the hazard warning lights. At the same time, the system sounds the vehicle horn and security horn to deter break-in and theft as well as to warn people around the vehicle.
The theft deterrent system has the active arming mode. There are 4 states; a disarmed state, an arming preparation state, an armed state and an alarm sounding state.
Disarmed state:
The alarm function is not operating.
The theft deterrent system is not operating.
Arming preparation state:
The time until the system goes into the armed state.
The theft deterrent system is not operating.
Armed state:
The theft deterrent system is operating.
Alarm sounding state:
The alarm function is operating.
Approx. 27.5 seconds
| Alarm Method | Hazard Warning Lights | Blinking |
| Vehicle Horn | Sounding
(approx. 0.4-second cycles) |
|
| Security Horn | Sounding
(approx. 0.4-second cycles) |
|
| Alarm Time | Approx. 27.5 seconds | |
FUNCTION OF MAIN COMPONENTS
| Component | Function |
|---|---|
| Security indicator light | Informs driver of theft deterrent system status. |
| Security horn | Sounds when attempted break-in or theft is detected. |
| Hazard warning lights | Blink when attempted break-in or theft is detected. |
| Vehicle horn | Sounds when attempted break-in or theft is detected. |
| Door courtesy light switch | Detects door status (open or closed). |
| Door unlock detection switch | Detects door status (locked or unlocked). |
| Engine hood courtesy switch | Detects engine hood status (open or closed). |
| Luggage compartment door courtesy light switch | Detects luggage compartment door status (open or closed). |
| Certification ECU (smart key ECU assembly) | ·
Receives wireless door lock/unlock signal. ·
Receives entry door lock/unlock signal. |
ACTIVE ARMING MODE
Active arming mode starts the alarm control immediately after the doors are locked.
Active arming mode:
This system operates as described in the diagram below when one of the items for each condition is met.
| Condition | Item |
|---|---|
| Condition [1] | In disarmed state 1, when the power switch is off, the system state is switched if the following condition is met:
·
With all doors, the engine hood and luggage compartment door closed, all doors are locked by wireless operation, the smart entry and start system or key linked power door lock operation. In disarmed state 1, when the power switch is off, the engine hood and luggage compartment door are closed, and all doors are locked, the system state is switched if the following condition is met: ·
All doors are closed when any door is opened. |
| Condition [2] | ·
Allow approx. 30 seconds to elapse. |
| Condition [3] | ·
All doors are unlocked by wireless operation, the smart entry and start system or key linked power door lock operation. ·
Any door is unlocked. ·
Any door is opened. ·
The power switch is turned on (ACC or IG). ·
The auxiliary battery is reconnected. |
| Condition [4] | ·
The engine hood is opened when the engine hood is closed. ·
The luggage compartment door is opened when the luggage compartment door is closed. ·
The auxiliary battery is reconnected. ·
Any door is opened when all doors are closed. ·
Any door is unlocked when all doors are locked. ·
When 5 seconds or more have elapsed after the power switch is turned off, the power switch is turned on (IG). |
| Condition [5] | ·
The power switch is turned on (READY). ·
All doors are unlocked by wireless operation, the smart entry and start system or key linked power door lock operation. ·
The power switch is turned on (ACC or IG) within 5 seconds after the power switch was turned off. |
| Condition [6] | ·
After approx. 27.5 seconds, alarm stops and system returns to armed state. |
| Condition [7] | ·
The luggage compartment door is opened by wireless operation or the smart entry and start system. |
| Condition [8] | ·
The luggage compartment door is closed when the engine hood is closed. ·
The engine hood is closed when the luggage compartment door is closed. |
| Condition [9] | ·
Any door is unlocked when all doors are locked. ·
Any door is opened. ·
The power switch is turned on (ACC or IG). ·
The auxiliary battery is reconnected. ·
All doors are unlocked by wireless operation, the smart entry and start system or key linked power door lock operation. |
| Condition [10] | In disarmed state 1, when the power switch is off, the system state is switched if the following condition is met:
·
With all doors closed, and the engine hood and luggage compartment door opened, all doors are locked by wireless operation, the smart entry and start system or key linked power door lock operation. In disarmed state 1, when the power switch is off, all doors are locked, the engine hood and luggage compartment door are open, the system state is switched if the following condition is met: ·
All doors are closed when any door is opened. |
| Condition [11] | ·
The engine hood is opened. ·
The luggage compartment door is opened. ·
The luggage compartment door is opened by wireless operation or the smart entry and start system. |
FORCED DOOR LOCK CONTROL
The forced door lock control prevents the vehicle from being tampered with. Immediately after a door is unlocked (armed starts), all doors are forced to lock by a forced door lock signal.
If the following conditions are met, the forced door lock control is operated.
The theft deterrent system is in the armed state.
Any door is unlocked.
PANIC ALARM CONTROL
Security horn does not sound when the panic alarm control is operated.
The panic alarm control makes it possible to voluntarily set off the panic alarm by pressing the panic switch on the wireless transmitter.
Conditions that cause the panic alarm control to set off the panic alarm:
The panic switch on the wireless transmitter is pressed under the following conditions:
The power switch is off.
The theft deterrent system is not in the alarm sounding state.
Conditions that cause the panic alarm control to shut off the alarm:
Any of the following conditions is met during panic alarm operation:
The power switch is turned to ON.
The panic switch is pressed again.
Any of the switches on the wireless transmitter (lock/unlock/luggage open) is pressed.
The panic alarm ends (approx. 27.5 seconds have elapsed).
The theft deterrent system switches to the alarm sounding state. Under this condition, the theft deterrent system is controlling the alarm rather than the panic alarm control. In order to cancel this alarm, refer to the theft deterrent system alarm sounding state cancellation procedure.
SECURITY INDICATOR LIGHT OUTPUT
According to the state of the theft deterrent system the main body ECU (multiplex network body ECU) outputs a signal to turn the security indicator light on. However, some of the actual lighting conditions of the security indicator light are different from the output signals of the main body ECU (multiplex network body ECU).
| State of Theft Deterrent System | Security Indicator Light | |
|---|---|---|
| Output Signal from Main Body ECU (Multiplex Network Body ECU) | Actual Lighting Condition | |
| Disarmed state (1), (2) | OFF | OFF (Engine immobiliser system unset)
BLINKING (Engine immobiliser system set) |
| Arming preparation state | ON | ON |
| Armed state | OFF | BLINKING |
| Alarm sounding state | ON | ON |
| Time | Security Indicator Light |
|---|---|
| 0.125 sec. | ON |
| 1.875 sec. | OFF |
When the engine immobiliser system is set, the security indicator light blinks during both the disarmed state and the armed state, due to output signals from the engine immobiliser system.