Home › Vehicle Interior › THEFT DETERRENT / KEYLESS ENTRY › ENGINE IMMOBILISER SYSTEM
RM2040EQ _58 Vehicle Interior _014723 THEFT DETERRENT / KEYLESS ENTRY _0075062 ENGINE IMMOBILISER SYSTEM C

THEFT DETERRENT / KEYLESS ENTRY  ENGINE IMMOBILISER SYSTEM  B278A  Short to GND in Immobiliser System Power Source Circuit  


DESCRIPTION

When there is a short to GND in the power supply for the transponder key amplifier of the power switch, the certification ECU (smart key ECU assembly) stores this DTC.

DTC No. Detection Item DTC Detection Condition Trouble Area Note
B278A Short to GND in Immobiliser System Power Source Circuit A short to GND in the power supply of the transponder key amplifier of the power switch (VC5 - VC5) (1 trip detection logic*).
·

Wire harness or connector

·

Power switch

·

Certification ECU (smart key ECU assembly)


DTC Output Confirmation Operation

With the shift lever in P, the key held near the power switch and a hybrid control system start operation is performed by pressing and holding the power switch when the key battery is depleted.



*: Only output while a malfunction is present.


Vehicle Condition and Fail-safe Operation when Malfunction Detected
Vehicle Condition when Malfunction Detected Fail-safe Operation when Malfunction Detected
Hybrid control system cannot be started when key battery is depleted by holding key near power switch and pressing and holding power switch with shift lever in P -

Related Data List and Active Test
DTC Code Data List and Active Test
B278A -

WIRING DIAGRAM

B278928
5.073,2.823 6.604,3.271 1.531,0.448 10 false Certification ECU (Smart Key ECU Assembly) 0.906,2.958 2.01,3.24 1.104,0.281 10 false Power Switch 0.896,2.813 1.406,3.125 0.51,0.313 10 false I58 5,1.167 5.229,1.313 0.229,0.146 10 false I87 5.052,0.99 5.167,1.135 0.115,0.146 10 false 9 5.052,1.927 5.167,2.073 0.115,0.146 10 false 6 1.958,1.979 2.073,2.125 0.115,0.146 10 false 6 1.958,1.052 2.292,1.385 0.333,0.333 10 false 10 5.302,1.167 5.615,1.313 0.313,0.146 10 false VC5 1.563,1.177 2.063,1.5 0.5,0.323 10 false VC5 5.302,2.094 5.719,2.24 0.417,0.146 10 false AGND 1.458,2.094 2.125,2.417 0.667,0.323 10 false AGND 5,2.083 5.229,2.229 0.229,0.146 10 false I86

CAUTION / NOTICE / HINT

NOTICE:
·

Before replacing the certification ECU (smart key ECU assembly), refer to the Service Bulletin.

·

After performing repairs, perform the operation that fulfills the DTC output confirmation operation, and then confirm that no DTCs are output again.



PROCEDURE

1.CHECK HARNESS AND CONNECTOR (CERTIFICATION ECU (SMART KEY ECU ASSEMBLY) - POWER SWITCH)
a.

Disconnect the I86 and I87 certification ECU (smart key ECU assembly) connectors.


b.

Disconnect the I58 power switch connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
I87-9 (VC5) - I58-10 (VC5) Always Below 1 Ω
I86-6 (AGND) - I58-6 (AGND) Always Below 1 Ω
I58-10 (VC5) - Body ground Always 10 kΩ or higher
I58-6 (AGND) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

2.CHECK CERTIFICATION ECU (SMART KEY ECU ASSEMBLY)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

2.CHECK CERTIFICATION ECU (SMART KEY ECU ASSEMBLY)
a.

Reconnect the I86 and I87 certification ECU (smart key ECU assembly) connectors.


b.

Reconnect the I58 power switch connector.


c.
B271009
1.313,0.188 1.708,0.448 0.396,0.26 1.833,1.646 2.406,2.031 false 1.198,1.656 0.625,2.052 false 1.417,0.24 1.74,0.427 0.323,0.188 10 I58 0.271,0.219 0.469,0.406 0.198,0.188 10 *a 2.969,3.281 3.302,3.5 0.333,0.219 10 GND 0.281,2.031 0.615,2.188 0.333,0.156 10 VC5 2.469,1.99 2.896,2.146 0.427,0.156 10 AGND
*a Component with harness connected
(Power Switch)


Using an oscilloscope, check the waveform.

HINT:

Perform this inspection on the engine switch side.


Measurement Condition:
Item Content
Tester Connection I58-10 (VC5) - I58-6 (AGND)
Tool Setting 2 V/DIV., 200 ms./DIV.
Condition Power switch off, key not in cabin, within 30 seconds after power switch pressed


OK:

Waveform is output normally (refer to illustration).



Result:
Proceed to
OK
NG



OK

NG

REPLACE CERTIFICATION ECU (SMART KEY ECU ASSEMBLY)