Home › Vehicle Interior › SUPPLEMENTAL RESTRAINT SYSTEMS › CURTAIN SHIELD AIRBAG ASSEMBLY
RM2040EQ _58 Vehicle Interior _014727 SUPPLEMENTAL RESTRAINT SYSTEMS _0075082 CURTAIN SHIELD AIRBAG ASSEMBLY A

SUPPLEMENTAL RESTRAINT SYSTEMS  CURTAIN SHIELD AIRBAG ASSEMBLY  REMOVAL  


CAUTION / NOTICE / HINT

HINT:
·

Use the same procedure for the RH side and LH side.

·

The procedure listed below is for the RH side.



PROCEDURE

Hide 1. PRECAUTION

CAUTION:

Be sure to read Precaution thoroughly before servicing (Click hereVehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM>PRECAUTION).


NOTICE:

After turning the power switch off, waiting time may be required before disconnecting the cable from the negative (-) auxiliary battery terminal. Therefore, make sure to read the disconnecting the cable from the negative (-) auxiliary battery terminal notices before proceeding with work (Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION).


Hide 2.REMOVE ROOF HEADLINING ASSEMBLY

Hide 62170A 3.REMOVE CURTAIN SHIELD AIRBAG ASSEMBLY

CAUTION:

When storing the curtain shield airbag assembly, keep the airbag deployment side facing upward.


a.

Check that the power switch is off.


b.

Check that the cable is disconnected from the negative (-) auxiliary battery terminal.

CAUTION:

Wait at least 90 seconds after disconnecting the cable from the negative (-) auxiliary battery terminal to disable the SRS system.



c.
B282221C02
1.917,2.802 1.917,2.156 false 2.594,0.792 2.188,0.792 false 1.552,1.844 1.365,1.656 1.365,1.656 0.75,1.656 false 0.594,1.573 0.813,1.792 0.219,0.219 10 false *2 1.823,2.802 2.052,3 0.229,0.198 10 false *1 2.031,0.708 2.26,0.948 0.229,0.24 10 false *3
*1 Protective Tape
*2 Airbag Connector
*3 Airbag Connector Lock


Using a screwdriver with the tip wrapped with protective tape, release the airbag connector lock and disconnect the curtain shield airbag connector.

NOTICE:

When disconnecting any airbag connector, take care not to damage the airbag wire harness.



d.
B282222

Using a clip remover, remove the pin.

HINT:

Perform the same procedure for the other pins.



e.

Using 2 screwdrivers, disengage the 2 claws and remove the clip from the body panel as shown in the illustration.

B282223C01
1.823,1.365 1.823,1.25 1.823,1.25 1.948,1.188 true 2.833,0.938 2.729,0.938 2.729,0.938 2.667,1.094 false 1.729,1.406 1.938,1.615 0.208,0.208 10 false *1 2.865,0.865 3.073,1.083 0.208,0.219 10 false *2
*1 Body Panel *2 Curtain Shield Airbag Assembly


HINT:

Perform the same procedure for the other clips.



f.

While holding the curtain shield airbag assembly, disengage the 5 claws.

B282224

NOTICE:

When removing the curtain shield airbag assembly, have assistants hold it to prevent it from bending.



g.

Remove the 2 bolts.

B282225


h.

Disengage the 2 hooks to remove the curtain shield airbag assembly.


i.

Remove the 2 spacers from the curtain shield airbag assembly.