Home › Vehicle Interior › SEAT BELT › SEAT BELT WARNING SYSTEM › 2012.02–2015.04
RM2040EQ _58 Vehicle Interior _014729 SEAT BELT _0075100 SEAT BELT WARNING SYSTEM U

SEAT BELT  SEAT BELT WARNING SYSTEM  TERMINALS OF ECU  


CHECK MAIN BODY ECU (MULTIPLEX NETWORK BODY ECU) AND INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY


a.

Disconnect the main body ECU (multiplex network body ECU) connectors.

B278841
2.229,3.771 2.552,3.979 0.323,0.208 5.833,5.01 6.156,5.219 0.323,0.208 3.906,5.031 4.229,5.24 0.323,0.208 1.125,5.01 1.448,5.219 0.323,0.208 1.781,6.292 2.104,6.5 0.323,0.208 4.927,6.292 5.25,6.5 0.323,0.208 3.417,7.531 3.74,7.74 0.323,0.208 4.688,3.771 5.01,3.979 0.323,0.208 4.083,1.135 4.083,0.802 4.083,0.802 4.198,0.802 false 1.677,1.99 1.938,1.99 false 1.677,1.552 1.938,1.552 false 3.479,7.563 3.833,7.781 0.354,0.219 10 MB 5.917,5.031 6.292,5.333 0.375,0.302 10 3E 1.208,5.031 1.625,5.302 0.417,0.271 10 3C 1.865,6.313 2.531,6.563 0.667,0.25 10 3B 5.021,6.313 5.521,6.594 0.5,0.281 10 3A 3.99,5.052 4.438,5.302 0.448,0.25 10 3D 4.76,3.802 5.135,4 0.375,0.198 10 I13 2.302,3.792 2.896,4.146 0.594,0.354 10 I12 5.875,2.146 6.208,2.417 0.333,0.271 10 3A 1.979,1.927 2.417,2.188 0.438,0.26 10 I12 1.979,1.479 2.354,1.656 0.375,0.177 10 I13 0.906,2.094 1.281,2.333 0.375,0.24 10 3D 1.073,2.688 1.365,2.906 0.292,0.219 10 3E 0.906,1.458 1.25,1.76 0.344,0.302 10 3C 5.854,1.458 6.271,1.75 0.417,0.292 10 3B 4.229,0.729 4.792,1.052 0.563,0.323 10 MB
*A Main body ECU (multiplex network body ECU) with 2 connectors - -
*1 Main body ECU (multiplex network body ECU) *2 2 connectors


B282096C57
2.229,3.771 2.552,3.979 0.323,0.208 5.833,5.01 6.156,5.219 0.323,0.208 3.906,5.031 4.229,5.24 0.323,0.208 1.125,5.01 1.448,5.219 0.323,0.208 1.781,6.292 2.104,6.5 0.323,0.208 4.927,6.292 5.25,6.5 0.323,0.208 3.417,7.531 3.74,7.74 0.323,0.208 4.688,3.771 5.01,3.979 0.323,0.208 4.083,1.125 4.083,0.844 4.083,0.844 4.198,0.844 false 1.823,2.146 2.073,2.146 false 1.823,1.792 2.073,1.792 false 1.604,3.125 1.604,1.469 1.604,1.469 1.708,1.469 false 1.604,1.792 1.698,1.792 false 1.604,2.146 1.708,2.146 false 0.781,2.771 1.031,2.771 false 1.771,0.969 1.771,0.677 1.771,0.677 1.865,0.677 false 3.479,7.563 3.917,7.823 0.438,0.26 10 false MB 1.198,5.042 1.542,5.354 0.344,0.313 10 false 3C 1.875,6.323 2.323,6.667 0.448,0.344 10 false 3B 5.01,6.323 5.281,6.656 0.271,0.333 10 false 3A 3.979,5.063 4.313,5.313 0.333,0.25 10 false 3D 4.75,3.813 5.156,4.219 0.406,0.406 10 false I13 2.302,3.813 2.792,4.167 0.49,0.354 10 false I12 5.917,5.042 6.26,5.406 0.344,0.365 10 false 3F 5.875,2.167 6.219,2.406 0.344,0.24 10 false 3A 2.125,2.083 2.479,2.448 0.354,0.365 10 false I12 2.125,1.719 2.5,2.073 0.375,0.354 10 false I13 0.906,2.094 1.385,2.656 0.479,0.563 10 false 3D 0.583,2.698 0.875,2.99 0.292,0.292 10 false 3F 0.906,1.458 1.229,1.792 0.323,0.333 10 false 3C 5.875,1.469 6.208,1.74 0.333,0.271 10 false 3B 4.229,0.781 4.677,1.042 0.448,0.26 10 false MB 0.323,0.229 0.719,0.771 0.396,0.542 10 false *A 1.906,0.615 2.229,0.948 0.323,0.333 10 false *1 1.542,3.135 1.792,3.396 0.25,0.26 10 false *2
*A Main body ECU (multiplex network body ECU) with 3 connectors - -
*1 Main body ECU (multiplex network body ECU) *2 3 connectors



b.

Measure the resistance and voltage according to the value(s) in the table below.

HINT:

Measure the values on the wire harness side with the connector disconnected.


Tester Connection Wiring Color Terminal Description Condition Specified Condition
MB-30 (BECU) - Body ground - Auxiliary battery power supply Power switch off 11 to 14 V
MB-31 (ALTB) - Body ground - Auxiliary battery power supply Power switch off
Always
11 to 14 V
MB-32 (IG) - Body ground - Power supply (IG signal) Power switch on (IG) → off 11 to 14 V → Below 1 V
MB-29 (ACC) - Body ground - Power supply (ACC signal) Power switch on (ACC) → off 11 to 14 V → Below 1 V
MB-11 (GND1) - Body ground - Ground Always Below 1 Ω
I12-3 (GND2) - Body ground W-B - Body ground Ground Always Below 1 Ω
MB-18 (DBKL) - Body ground - Driver seat belt buckle switch signal Driver seat belt fastened 10 kΩ or higher
MB-18 (DBKL) - Body ground - Driver seat belt buckle switch signal Driver seat belt unfastened Below 1 Ω
I13-1 (LCTY) - Body ground LG - Body ground Rear door courtesy light switch LH input Rear door LH closed (OFF) → open (ON) 10 kΩ or higher → Below 1 Ω
I13-6 (RCTY) - Body ground B - Body ground Rear door courtesy light switch RH input Rear door RH closed (OFF) → open (ON) 10 kΩ or higher → Below 1 Ω

If the result is not as specified, there may be a malfunction in the wire harness.



CHECK COMBINATION METER ASSEMBLY


a.

Disconnect the I18 combination meter assembly connector.

E224288E08
1.875,0.26 2.198,0.469 0.323,0.208 5.104,0.26 5.427,0.469 0.323,0.208 1.948,0.292 2.229,0.51 0.281,0.219 10 false I18 5.167,0.292 5.573,0.573 0.406,0.281 10 false I17


b.

Measure the resistance according to the value(s) in the table below.

HINT:

Measure the values on the wire harness side with the connector disconnected.


Tester Connection Wiring Color Terminal Description Condition Specified Condition
I18-7 (ES) - Body ground BR - Body ground Ground Always Below 1 Ω
I18-20 (P/SB) - Body ground LG - Body ground Front passenger seat belt buckle switch signal Front passenger seat occupied, seat belt fastened 10 kΩ or higher
I18-20 (P/SB) - Body ground LG - Body ground Front passenger seat belt buckle switch signal Front passenger seat occupied, seat belt unfastened Below 1 Ω
I18-5 (RRSB) - Body ground LG - Body ground Rear RH seat belt buckle switch signal Rear RH seat belt fastened Below 1 Ω
I18-5 (RRSB) - Body ground LG - Body ground Rear RH seat belt buckle switch signal Rear RH seat belt unfastened 10 kΩ or higher
I18-4 (RCSB) - Body ground P - Body ground Rear center seat belt buckle switch signal Rear center seat belt fastened Below 1 Ω
I18-4 (RCSB) - Body ground P - Body ground Rear center seat belt buckle switch signal Rear center seat belt unfastened 10 kΩ or higher
I18-3 (RLSB) - Body ground L - Body ground Rear LH seat belt buckle switch signal Rear LH seat belt fastened Below 1 Ω
I18-3 (RLSB) - Body ground L - Body ground Rear LH seat belt buckle switch signal Rear LH seat belt unfastened 10 kΩ or higher

If the result is not as specified, there may be a malfunction in the wire harness.


c.

Reconnect the I18 combination meter assembly connector.


d.

Measure the voltage according to the value(s) in the table below.

Tester Connection Wiring Color Terminal Description Condition Specified Condition
I18-1 (B) - Body ground W - Body ground Auxiliary battery power supply Power switch off 11 to 14 V
I18-13 (IG+) - Body ground L - Body ground Power supply
(IG signal)
Power switch off Below 1 V
I18-13 (IG+) - Body ground L - Body ground Power supply
(IG signal)
Power switch on (IG) 11 to 14 V

If the result is not as specified, the combination meter assembly may have a malfunction.