1.INSPECT DRIVER SEAT BELT WARNING LIGHT
The seat belt warning light on the combination meter assembly is used for both the driver seat and front passenger seat.
Turn the power switch on (IG).
When the shift lever is in P and the driver seat belt is not fastened, check that the seat belt warning light on the combination meter assembly illuminates.
Lift up the vehicle using a swing arm type lift (See page General>INTRODUCTION>REPAIR INSTRUCTION>VEHICLE LIFT AND SUPPORT LOCATIONS).
Power switch on (READY).
Check the state of the seat belt warning light on the combination meter assembly under the following conditions:
Step 1:
When the driver seat belt is not fastened, the shift lever is in any position other than P and the parking brake is released for 30 seconds or more, check that the seat belt warning light on the combination meter assembly blinks.
Step 2:
When the driver seat belt is not fastened and the vehicle is driven at approximately 20 km/h (12 mph) or more, check that the seat belt warning light on the combination meter assembly blinks.
After 150 seconds, check that the seat belt warning light on the combination meter assembly changes from blinking to illuminated.
Step 3:
Starting from step 1 with the seat belt warning light on the combination meter assembly blinking, when the shift lever is moved to P, check that the seat belt warning light on the combination meter assembly changes from blinking to illuminated.
Step 4:
Starting from step 1 with the seat belt warning light on the combination meter assembly blinking, when the parking brake is applied, check that the seat belt warning light on the combination meter assembly changes from blinking to illuminated.
Step 5:
Starting from step 1 with the seat belt warning light on the combination meter assembly blinking, when the driver seat belt is fastened, check that the seat belt warning light on the combination meter assembly turns off.
2.INSPECT FRONT PASSENGER SEAT BELT WARNING LIGHT
The seat belt warning light on the combination meter assembly is used for both the driver seat and front passenger seat.
Turn the power switch on (IG).
Place a weight of 20 kg (44.0 lb) on the front passenger seat.
Place the weight on the seat cushion and do not allow it to come into contact with the seatback.
Fasten the driver seat belt.
When the shift lever is in P, the front passenger seat is occupied and the front passenger seat belt is not fastened, check that the seat belt warning light on the combination meter assembly illuminates.
Lift up the vehicle using a swing arm type lift (See page General>INTRODUCTION>REPAIR INSTRUCTION>VEHICLE LIFT AND SUPPORT LOCATIONS).
Power switch on (READY).
Check the state of the seat belt warning light on the combination meter assembly under the following conditions:
Step 1:
When the front passenger seat belt is not fastened, the shift lever is in any position other than P and the parking brake is released for 30 seconds or more, check that the seat belt warning light on the combination meter assembly blinks.
Step 2:
When the front passenger seat belt is not fastened and the vehicle is driven at approximately 20 km/h (12 mph) or more, check that the seat belt warning light on the combination meter assembly blinks.
After 150 seconds, check that the seat belt warning light on the combination meter assembly changes from blinking to illuminated.
Step 3:
Starting from step 1 with the seat belt warning light on the combination meter assembly blinking, when the shift lever is moved to P, check that the seat belt warning light on the combination meter assembly changes from blinking to illuminated.
Step 4:
Starting from step 1 with the seat belt warning light on the combination meter assembly blinking, when the parking brake is applied, check that the seat belt warning light on the combination meter assembly changes from blinking to illuminated.
Step 5:
Starting from step 1 with the seat belt warning light on the combination meter assembly blinking, the front passenger seat belt not fastened and the weight on the front passenger seat, check that the seat belt warning light on the combination meter assembly turns off when the weight is removed from the front passenger seat.
Step 6:
Starting from step 1 with the seat belt warning light on the combination meter assembly blinking, when the front passenger seat belt is fastened, check that the seat belt warning light on the combination meter assembly turns off.
3.INSPECT REAR SEAT BELT WARNING
| *a | Rear Seat Belt Warning Light (Clock Assembly) |
| *b | LH |
| *c | Center |
| *d | RH |
Open and then close either rear door.
Turn the power switch on (IG).
When the rear seat belt is not fastened, check that the rear seat belt warning light on the clock assembly illuminates.
When either condition is met, check that the rear seat belt warning light on the clock assembly turns off:
The rear seat belt is fastened.
The vehicle is not driven and either rear door is opened.
4.INSPECT SEAT BELT WARNING BUZZER
The seat belt warning buzzer can be customized. Make sure that this function is ON.
Click hereVehicle Interior>SEAT BELT>SEAT BELT WARNING SYSTEM>CUSTOMIZE PARAMETERS
Place a weight of 20 kg (44.0 lb) on the front passenger seat.
Place the weight on the seat cushion and do not allow it to come into contact with the seatback.
Lift up the vehicle using a swing arm type lift (See page General>INTRODUCTION>REPAIR INSTRUCTION>VEHICLE LIFT AND SUPPORT LOCATIONS).
Power switch on (READY).
Check that the seat belt warning buzzer in the combination meter assembly sounds at an interval of 1.2 seconds for 30 seconds.
After the seat belt warning buzzer has been sounding for 30 seconds at an interval of 1.2 seconds, check that the seat belt warning buzzer in the combination meter assembly sounds at an interval of 0.4 seconds for 90 seconds.
Check that the seat belt warning buzzer in the combination meter assembly stops 2 minutes after it started sounding at an interval of 1.2 seconds.
After the buzzer has stopped, turn the power switch off and then start the hybrid control system again. Drive the vehicle at approximately 20 km/h (12 mph) or more while the driver, front passenger or rear seat belt is not fastened, and check that the buzzer sounds again.
After the buzzer has stopped, fasten the driver, front passenger or rear seat belt. Drive the vehicle at approximately 20 km/h (12 mph) or more and unfasten the driver, front passenger or rear seat belt, and check that the buzzer sounds again.
After the buzzer has stopped, stop the vehicle, move the shift lever to R, and then move it to D. Drive the vehicle at approximately 20 km/h (12 mph) or more, and check that the buzzer sounds again.