Home › Vehicle Interior › HEATING / AIR CONDITIONING › AIR CONDITIONING SYSTEM
RM2040EQ _58 Vehicle Interior _014730 HEATING / AIR CONDITIONING _0075108 AIR CONDITIONING SYSTEM J

HEATING / AIR CONDITIONING  AIR CONDITIONING SYSTEM  PTC Heater Circuit  


DESCRIPTION

The air conditioning amplifier assembly sends operation signals to the PTC HTR relays when quick heater assembly (PTC heater) operation conditions are met. Based on the signals from the air conditioning amplifier assembly, the PTC HTR relays turn on, and power is supplied to the quick heater assembly (PTC heater) installed in the air conditioning radiator assembly.

Quick Heater Assembly (PTC Heater) Operation Condition
Control ECU Condition
Air Conditioning Amplifier Assembly Blower motor on
Temperature set to MAX HOT
ECO mode switch (eco switch assembly) off
IDH terminal signal less than 1 V
(Inverter with converter assembly overload not detected)
Coolant temperature 70°C or lower
Ambient temperature 10°C or lower

WIRING DIAGRAM

E230450E01
5.656,3.5 5.885,3.646 0.229,0.146 10 false I77 5.656,3.625 6.917,3.948 1.26,0.323 10 false Air Conditioning Amplifier Assembly 3.104,1.125 4.521,1.281 1.417,0.156 10 false PTC HTR NO. 1 Relay 3.125,0.302 3.219,0.458 0.094,0.156 10 false 2 4.417,0.302 4.51,0.458 0.094,0.156 10 false 1 5.594,0.302 5.771,0.458 0.177,0.156 10 false 15 5.844,0.385 6.229,0.542 0.385,0.156 10 false PTC1 5.594,1.49 5.771,1.646 0.177,0.156 10 false 16 5.844,1.573 6.229,1.729 0.385,0.156 10 false PTC2 3.125,0.781 3.219,0.938 0.094,0.156 10 false 3 4.417,0.781 4.51,0.938 0.094,0.156 10 false 5 3.104,2.313 4.521,2.469 1.417,0.156 10 false PTC HTR NO. 2 Relay 3.125,1.49 3.219,1.646 0.094,0.156 10 false 2 4.417,1.49 4.51,1.646 0.094,0.156 10 false 1 3.125,1.969 3.219,2.125 0.094,0.156 10 false 3 4.417,1.969 4.51,2.125 0.094,0.156 10 false 5 1.802,0.521 2.323,0.677 0.521,0.156 10 false A/C-IG1 1.552,1 2.583,1.156 1.031,0.156 10 false PTC HTR NO. 1 1.552,2.188 2.583,2.344 1.031,0.156 10 false PTC HTR NO. 2 2.979,4.271 4.448,4.427 1.469,0.156 10 false Quick Heater Assembly 3.094,3.885 3.208,4.042 0.115,0.156 10 false E 2.792,3.792 2.885,3.948 0.094,0.156 10 false 1 2.75,3.969 2.979,4.198 0.229,0.229 10 false a2 4.198,3.885 4.313,4.042 0.115,0.156 10 false B 4.542,3.792 4.635,3.948 0.094,0.156 10 false 2 4.479,3.969 4.688,4.125 0.208,0.156 10 false I41 4.198,3.438 4.313,3.594 0.115,0.156 10 false B 4.542,3.344 4.635,3.5 0.094,0.156 10 false 1 4.479,3.521 4.688,3.677 0.208,0.156 10 false I41 0.208,0.385 1.083,0.542 0.875,0.156 10 false from IG Relay 0.208,0.865 1.083,1.188 0.875,0.323 10 false from Auxiliary Battery

CAUTION / NOTICE / HINT

NOTICE:

Inspect the fuses for circuits related to this system before performing the following inspection procedure.


PROCEDURE

1.PERFORM ACTIVE TEST USING INTELLIGENT TESTER
a.

Connect the intelligent tester to the DLC3.


b.

Turn the power switch on (IG).


c.

Turn the intelligent tester on.


d.

Enter the following menus: Body / Air Conditioner / Active Test.


e.

Check the operation by referring to the table below.

Body Electrical > Air Conditioner > Active Test
Tester Display Measurement Item Control Range Diagnostic Note
Heater Active Level Quick heater assembly Min.: 0, Max.: 2 -
Body Electrical > Air Conditioner > Active Test
Tester Display
Heater Active Level
50004 121 33
OK:

Quick Heater Active Level changes normally.



Result:
Proceed to
OK
NG



OK

2.INSPECT PTC HEATER RELAY (PTC HTR NO. 1, PTC HTR NO. 2)

NG

PROCEED TO NEXT SUSPECTED AREA SHOWN IN PROBLEM SYMPTOMS TABLE

2.INSPECT PTC HEATER RELAY (PTC HTR NO. 1, PTC HTR NO. 2)
a.
E218162E05
1.82,0.756 1.924,0.897 0.104,0.141 10 3 0.995,1.739 1.099,1.879 0.104,0.141 10 3 3.135,0.756 3.239,0.897 0.104,0.141 10 5 1.133,0.438 1.237,0.579 0.104,0.141 10 5 3.144,1.245 3.248,1.385 0.104,0.141 10 2 1.42,0.603 1.524,0.744 0.104,0.141 10 2 1.811,1.246 1.915,1.386 0.104,0.141 10 1 0.177,0.559 0.281,0.7 0.104,0.141 10 1 0.818,0.86 1.035,0.505 1.035,0.505 1.104,0.505 false 0.569,1.008 0.351,0.653 0.351,0.653 0.282,0.653 false 1.073,1.01 1.322,0.685 1.322,0.685 1.39,0.685 false 0.826,1.55 0.913,1.822 0.913,1.822 0.974,1.822 false

Remove the PTC HTR NO. 1 relay and PTC HTR NO. 2 relay.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
3 - 5 Auxiliary battery voltage is not applied between terminals 1 and 2 10 kΩ or higher
3 - 5 Auxiliary battery voltage is applied between terminals 1 and 2 Below 1 Ω



Result:
Proceed to
OK
NG



OK

3.CHECK HARNESS AND CONNECTOR (PTC HTR NO. 1 RELAY, PTC HTR NO. 2 RELAY - POWER SOURCE)

NG

3.CHECK HARNESS AND CONNECTOR (PTC HTR NO. 1 RELAY, PTC HTR NO. 2 RELAY - POWER SOURCE)
a.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
PTC1
Tester Connection Condition Specified Condition
3 - Body ground Power switch off 11 to 14 V
2 - Body ground Power switch on (IG) 11 to 14 V

PTC2
Tester Connection Condition Specified Condition
3 - Body ground Power switch off 11 to 14 V
2 - Body ground Power switch on (IG) 11 to 14 V



Result:
Proceed to
OK
NG



OK

4.CHECK HARNESS AND CONNECTOR (PTC HTR NO. 1 RELAY, PTC HTR NO. 2 RELAY - AIR CONDITIONING AMPLIFIER ASSEMBLY)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

4.CHECK HARNESS AND CONNECTOR (PTC HTR NO. 1 RELAY, PTC HTR NO. 2 RELAY - AIR CONDITIONING AMPLIFIER ASSEMBLY)
a.

Disconnect the I77 air conditioning amplifier assembly connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
PTC1
Tester Connection Condition Specified Condition
1 - I77-15 (PTC1) Always Below 1 Ω
1 - Body ground Always 10 kΩ or higher

PTC2
Tester Connection Condition Specified Condition
1 - I77-16 (PTC2) Always Below 1 Ω
1 - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

5.CHECK HARNESS AND CONNECTOR (PTC HTR NO. 1 RELAY, PTC HTR NO. 2 RELAY - QUICK HEATER ASSEMBLY)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

5.CHECK HARNESS AND CONNECTOR (PTC HTR NO. 1 RELAY, PTC HTR NO. 2 RELAY - QUICK HEATER ASSEMBLY)
a.

Disconnect the I41 quick heater assembly connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
PTC1
Tester Connection Condition Specified Condition
5 - I41-1 (B) Always Below 1 Ω
5 - Body ground Always 10 kΩ or higher

PTC2
Tester Connection Condition Specified Condition
5 - I41-2 (B) Always Below 1 Ω
5 - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

6.INSPECT QUICK HEATER ASSEMBLY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

6.INSPECT QUICK HEATER ASSEMBLY
a.

b.
E230975C04
1.469,0.135 1.958,0.427 0.49,0.292 1.458,1.792 1.948,2.083 0.49,0.292 1.573,1.104 1.354,0.76 1.354,0.76 1.146,0.76 false 1.854,1.083 2.073,0.74 2.073,0.74 2.271,0.74 false 0.979,0.667 1.135,0.865 0.156,0.198 10 false B 0.177,0.146 0.521,0.438 0.344,0.292 10 false *a 2.333,0.656 2.542,0.854 0.208,0.198 10 false B 1.625,0.198 1.938,0.385 0.313,0.188 10 false I41 1.635,1.865 1.958,2.031 0.323,0.167 10 false a2
*a Component without harness connected
(Quick Heater Assembly)


Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
I41-1 (B)- a1-1 (E) Always Below 1 Ω
I41-2 (B)- a1-1 (E) Always Below 1 Ω



Result:
Proceed to
OK
NG



OK

REPLACE AIR CONDITIONING AMPLIFIER ASSEMBLY

NG