CHECK REAR SUNSHADE RELAY (REAR WINDOW SHADE ASSEMBLY)
Disconnect the N19 rear sunshade relay (rear window shade assembly) connector.
Measure the voltage and resistance according to the value(s) in the table below.
Measure the values on the wire harness side with the connector disconnected.
| Tester Connection | Wiring Color | Terminal Description | Condition | Specified Condition |
|---|---|---|---|---|
| N19-7 (IG) - N19-1 (E) | V - W-B | IG power supply | Power switch off | Below 1 V |
| N19-7 (IG) - N19-1 (E) | V - W-B | IG power supply | Power switch on (IG) | 11 to 14 V |
| N19-8 (B) - N19-1 (E) | P - W-B | Auxiliary battery power supply | Power switch off | 11 to 14 V |
| N19-1 (E) - Body ground | W-B - Body ground | Ground | Always | Below 1 Ω |
If the result is not as specified, there may be a malfunction in the wire harness.
Reconnect the N19 rear sunshade relay (rear window shade assembly) connector.
Measure the voltage according to the value(s) in the table below.
| Tester Connection | Wiring Color | Terminal Description | Condition | Specified Condition |
|---|---|---|---|---|
| N19-3 (REV) - N19-1 (E) | B - W-B | Reverse signal | Power switch on (IG), shift lever in any position other than R | 11 to 14 V |
| N19-3 (REV) - N19-1 (E) | B - W-B | Reverse signal | Power switch on (IG), shift lever in R | Below 1 V |
| N19-5 (SW) - N19-1 (E) | R - W-B | Rear sunshade switch signal | Power switch on (IG), rear sunshade switch not pushed | 11 to 14 V |
| N19-5 (SW) - N19-1 (E) | R - W-B | Rear sunshade switch signal | Power switch on (IG), rear sunshade switch pushed | Below 1.5 V |
If the result is not as specified, the rear sunshade relay (rear window shade assembly) may have a malfunction.
CHECK INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY AND MAIN BODY ECU (MULTIPLEX NETWORK BODY ECU)
Disconnect the MB and I12 main body ECU (multiplex network body ECU) connector.
| *A | Main body ECU (multiplex network body ECU) (2 Connector Type) | - | - |
| *1 | Main body ECU (multiplex network body ECU) | *2 | 2 connectors |
| *A | Main body ECU (multiplex network body ECU) (3 Connector Type) | - | - |
| *1 | Main body ECU (multiplex network body ECU) | *2 | 3 connectors |
Measure the voltage and resistance according to the value(s) in the table below.
Measure the values on the wire harness side with the connectors disconnected.
| Tester Connection | Wiring Color | Terminal Description | Condition | Specified Condition |
|---|---|---|---|---|
| MB-11 (GND1) - Body ground | - | Ground | Always | Below 1 Ω |
| I12-3 (GND2) - Body ground | W-B - Body ground | Ground | Always | Below 1 Ω |
| MB-30 (BECU) - Body ground | - | Auxiliary battery power supply | Power switch off | 11 to 14 V |
| MB-29 (ACC) - Body ground | - | ACC power supply | Power switch on (ACC) | 11 to 14 V |
| MB-29 (ACC) - Body ground | - | ACC power supply | Power switch off | Below 1 V |
| MB-31 (ALTB) - Body ground | - | Auxiliary battery power supply | Power switch off | 11 to 14 V |
| MB-32 (IG) - Body ground | - | IG power supply | Power switch on (IG) | 11 to 14 V |
| MB-32 (IG) - Body ground | - | IG power supply | Power switch off | Below 1 V |
If the result is not as specified, there may be a malfunction in the wire harness.
Reconnect the I12 and MB junction block connectors.
Measure the voltage according to the value(s) in the table below.
| Tester Connection | Wiring Color | Terminal Description | Condition | Specified Condition |
|---|---|---|---|---|
| I13-15 (REV) - Body ground | B - Body ground | Reverse signal | Power switch on (IG), shift lever in any position other than R | 11 to 14 V |
| I13-15 (REV) - Body ground | B - Body ground | Reverse signal | Power switch on (IG), shift lever in R | Below 1 V |
If the result is not as specified, the main body ECU (multiplex network body ECU) or instrument panel junction block assembly may have a malfunction.