Home › Vehicle Exterior › WINDOW / GLASS › POWER WINDOW REGULATOR MOTOR(for Front Door)
RM2040EQ _59 Vehicle Exterior _014733 WINDOW / GLASS _0075138 POWER WINDOW REGULATOR MOTOR(for Front Door) G

WINDOW / GLASS  POWER WINDOW REGULATOR MOTOR(for Front Door)  INSPECTION  


PROCEDURE

Hide 85720D 1.INSPECT POWER WINDOW REGULATOR MOTOR ASSEMBLY LH

a.
B127535
0.125,0.115 0.292,0.292 0.167,0.177 10 false *a 1.594,0.938 1.771,1.146 0.177,0.208 10 false *c 1.25,1.646 1.406,1.844 0.156,0.198 10 false *d 0.719,0.281 0.885,0.458 0.167,0.177 10 false *b
*a Component without harness connected
(Power Window Regulator Motor Assembly LH)
*b Motor Gear
*c Counterclockwise
*d Clockwise


Apply auxiliary battery voltage to the motor connector according to the table below.

NOTICE:

Do not apply auxiliary battery voltage to any terminals except terminals 1 and 2.


Standard:
Measurement Condition Specified Condition
Auxiliary battery positive (+) → Terminal 2
Auxiliary battery negative (-) → Terminal 1
Motor gear rotates clockwise
Auxiliary battery positive (+) → Terminal 1
Auxiliary battery negative (-) → Terminal 2
Motor gear rotates counterclockwise


If the result is not as specified, replace the power window regulator motor assembly LH.


Hide 85710E 2.INSPECT POWER WINDOW REGULATOR MOTOR ASSEMBLY RH

a.
B203474
2.396,2.5 2.396,2.188 2.396,2.188 2.813,2.188 false 2.271,2.5 2.271,2.188 2.271,2.188 1.75,2.188 false 2.25,2.688 2.25,2.979 2.25,2.979 1.802,2.979 false 2.427,2.677 2.427,2.979 2.427,2.979 2.667,2.979 false 0.094,0.083 0.271,0.24 0.177,0.156 10 false *a 2.708,2.906 3.229,3.094 0.521,0.188 10 false DWN1 2.854,2.104 2.99,2.24 0.135,0.135 10 false E 1.625,2.104 1.74,2.24 0.115,0.135 10 false B 1.5,2.896 1.927,3.094 0.427,0.198 10 false UP1 0.302,1.813 0.469,1.969 0.167,0.156 10 false *b 0.948,2.24 1.115,2.396 0.167,0.156 10 false *c
*a Component without harness connected
*b Clockwise
*c Counterclockwise


Apply positive (+) auxiliary battery voltage to connector terminal 2 (B).

NOTICE:

Do not apply positive (+) auxiliary battery voltage to any terminals other than terminal 2 (B) to avoid damaging the pulse sensor inside the motor.



b.

Connect a ground lead to connector terminals 1 (E) and 7 (DWN1) or 10 (UP1).


c.

Check that the motor gear rotates smoothly as follows:

OK:
Measurement Condition Specified Condition
1.

Connect the positive (+) auxiliary battery lead to terminal 2 (B), connect a negative (-) auxiliary battery lead to terminal 1 (E), and keep them connected for 3 seconds or more.

2.

With terminals 2 (B) and 1 (E) connected, connect a negative (-) auxiliary battery lead to terminal 10 (UP1).

3.

Disconnect and reconnect the negative (-) auxiliary battery lead for terminal 10 (UP1) within 1 second.


Motor gear rotates counterclockwise
1.

Connect a positive (+) auxiliary battery lead to terminal 2 (B), connect a negative (-) auxiliary battery lead to terminal 1 (E), and keep them connected for 3 seconds or more.

2.

With terminals 2 (B) and 1 (E) connected, connect a negative (-) auxiliary battery lead to terminal 7 (DWN1).

3.

Disconnect and reconnect the negative (-) auxiliary battery lead for terminal 7 (DWN1) within 1 second.


Motor gear rotates clockwise


If the result is not as specified, replace the power window regulator motor assembly RH.


NOTICE:

Reset the power window regulator motor (initialize the pulse sensor) after installing the power window regulator motor and regulator assembly onto the door.