Home › Vehicle Exterior › WINDOW / GLASS › WINDOW DEFOGGER SYSTEM
RM2040EQ _59 Vehicle Exterior _014733 WINDOW / GLASS _0075140 WINDOW DEFOGGER SYSTEM U

WINDOW / GLASS  WINDOW DEFOGGER SYSTEM  TERMINALS OF ECU  


CHECK AIR CONDITIONING AMPLIFIER ASSEMBLY


a.

Disconnect the I77 air conditioning amplifier assembly connector.

B274525
3.448,0.188 3.823,0.417 0.375,0.229 3.552,0.208 4.073,0.573 0.521,0.365 10 false I77


b.

Measure the voltage and resistance according to the value(s) in the table below.

HINT:

Measure the values on the wire harness side with the connector disconnected.


Tester Connection Wiring Color Terminal Description Condition Specified Condition
I77-1 (IG+) - I77-14 (GND) B - W-B Power source (IG) Power switch on (IG) 11 to 14 V
I77-1 (IG+) - I77-14 (GND) B - W-B Power source (IG) Power switch off Below 1 V
I77-21 (B) - I77-14 (GND) Y - W-B Auxiliary battery power supply Power switch off 11 to 14 V
I77-14 (GND) - Body ground W-B - Body ground Ground Always Below 1 Ω

If the result is not as specified, there may be a malfunction in the wire harness.


c.

Reconnect the I77 air conditioning amplifier assembly connector.


d.

Measure the voltage and check for pulses according to the value(s) in the table below.

Tester Connection Wiring Color Terminal Description Condition Specified Condition
I77-38 (RDFG) - I77-14 (GND) P - W-B Rear window defogger signal Power switch on (IG), rear window defogger switch off 11 to 14 V
I77-38 (RDFG) - I77-14 (GND) P - W-B Rear window defogger signal Power switch on (IG), rear window defogger switch on Below 2.2 V
I77-37 (LIN1) - I77-14 (GND) V - W-B LIN communication line Power switch on (IG) Pulse generation

If the result is not as specified, the air conditioning amplifier assembly may have a malfunction.



CHECK AIR CONDITIONING PANEL (HEATER CONTROL SWITCH BOARD)


a.

Disconnect the I56 air conditioning panel (heater control switch board) connector.

B270939
3.385,0.146 3.781,0.396 0.396,0.25 3.479,0.177 3.938,0.458 0.458,0.281 10 false I56


b.

Measure the voltage and resistance according to the value(s) in the table below.

HINT:

Measure the values on the wire harness side with the connector disconnected.


Tester Connection Wiring Color Terminal Description Condition Specified Condition
I56-2 (IG+) - I56-6 (GND) R - W-B Power source (IG) Power switch on (IG) 11 to 14 V
I56-2 (IG+) - I56-6 (GND) R - W-B Power source (IG) Power switch off Below 1 V
I56-6 (GND) - Body ground W-B - Body ground Ground Always Below 1 Ω

If the result is not as specified, there may be a malfunction in the wire harness.


c.

Reconnect the I56 air conditioning panel (heater control switch board) connector.


d.

Check for pulses according to the value(s) in the table below.

Tester Connection Wiring Color Terminal Description Condition Specified Condition
I56-9 (LIN1) - I56-6 (GND) V - W-B LIN communication line Power switch on (IG) Pulse generation

If the result is not as specified, the air conditioning panel (heater control switch board) may have a malfunction.