Home › Vehicle Exterior › WINDOW / GLASS › POWER WINDOW CONTROL SYSTEM
RM2040EQ _59 Vehicle Exterior _014733 WINDOW / GLASS _0075142 POWER WINDOW CONTROL SYSTEM U

WINDOW / GLASS  POWER WINDOW CONTROL SYSTEM  TERMINALS OF ECU  


POWER WINDOW REGULATOR MASTER SWITCH ASSEMBLY


B164269
3.427,0.083 3.781,0.302 0.354,0.219 3.49,0.104 3.896,0.271 0.406,0.167 10 false J10

a.

Disconnect the J10 power window regulator master switch assembly connector.


b.

Measure the voltage and resistance according to the value(s) in the table below.

HINT:

Measure the values on the wire harness side with the connector disconnected.


Tester Connection Wiring Color Terminal Description Condition Specified Condition
J10-9 (E) - Body ground W-B - Body ground Ground Always Below 1 Ω
J10-6 (B) - J10-9 (E) GR - W-B Power supply Power switch on (IG) 11 to 14 V

If the result is not as specified, there may be a malfunction in the wire harness.


c.

Reconnect the J10 power window regulator master switch assembly.


d.

Measure the voltage according to the value(s) in the table below.

Tester Connection Wiring Color Terminal Description Condition Specified Condition
J10-1 (U) - J10-9 (E) BE - W-B Power window motor UP output Power switch on (IG), driver door power window switch OFF → UP (Manual operation) 11 to 14 V → Below 1 V
J10-4 (A) - J10-9 (E) B - W-B Power window motor AUTO UP output Power switch on (IG), driver door power window fully open → driver door power window switch UP (AUTO UP position) → driver door power window fully closed 11 to 14 V → Below 1 V → 11 to 14 V
Power window motor AUTO DOWN output Power switch on (IG), driver door power window fully closed → driver door power window switch DOWN (AUTO DOWN position) → driver door power window fully open 11 to 14 V → Below 1 V → 11 to 14 V
J10-5 (D) - J10-9 (E) V - W-B Power window motor DOWN output Power switch on (IG), driver door power window switch OFF → DOWN (Manual operation) 11 to 14 V → Below 1 V
J10-12 (U) - J10-9 (E) W - W-B Power window motor UP output Power switch on (IG), front passenger door power window switch OFF → UP (Manual operation) Below 1 V → 11 to 14 V
J10-13 (D) - J10-9 (E) R - W-B Power window motor DOWN output Power switch on (IG), front passenger door power window switch OFF → DOWN (Manual operation) Below 1 V → 11 to 14 V
J10-18 (U) - J10-9 (E) L - W-B Power window motor UP output Power switch on (IG), rear LH door power window switch OFF → UP (Manual operation) Below 1 V → 11 to 14 V
J10-10 (D) - J10-9 (E) V - W-B Power window motor DOWN output Power switch on (IG), rear LH door power window switch OFF → DOWN (Manual operation) Below 1 V → 11 to 14 V
J10-16 (U) - J10-9 (E) Y - W-B Power window motor UP output Power switch on (IG), rear RH door power window switch OFF → UP (Manual operation) Below 1 V → 11 to 14 V
J10-15 (D) - J10-9 (E) LG - W-B Power window motor DOWN output Power switch on (IG), rear RH door power window switch OFF → DOWN (Manual operation) Below 1 V → 11 to 14 V

If the result is not as specified, the power window regulator master switch assembly may have a malfunction.



CHECK POWER WINDOW REGULATOR SWITCH ASSEMBLY (for Front Passenger Door)


B164270
3.417,0.135 3.813,0.344 0.396,0.208 3.479,0.156 3.885,0.563 0.406,0.406 10 false K11

a.

Disconnect the K11 power window regulator switch assembly (for front passenger door) connector.


b.

Measure the voltage according to the value(s) in the table below.

HINT:

Measure the values on the wire harness side with the connector disconnected.


Tester Connection Wiring Color Terminal Description Condition Specified Condition
K11-3 (B) - Body ground GR - Body ground Power supply Power switch on (IG) 11 to 14 V

If the result is not as specified, there may be a malfunction in the wire harness.


c.

Reconnect the K11 power window regulator switch assembly (for front passenger door).


d.

Measure the voltage according to the value(s) in the table below.

Tester Connection Wiring Color Terminal Description Condition Specified Condition
K11-4 (U) - Body ground G - Body ground Power window motor UP output Power switch on (IG), front passenger door power window switch OFF → UP (Manual operation) Below 1 V → 11 to 14 V
K11-1 (D) - Body ground Y - Body ground Power window motor DOWN output Power switch on (IG), front passenger door power window switch OFF → DOWN (Manual operation) Below 1 V → 11 to 14 V

If the result is not as specified, the power window regulator switch assembly (for front passenger door) may have a malfunction.



CHECK POWER WINDOW REGULATOR SWITCH ASSEMBLY (for Rear LH Door)


B164270
3.469,0.125 3.833,0.333 0.365,0.208 3.552,0.135 4.052,0.521 0.5,0.385 10 false M6

a.

Disconnect the M6 power window regulator switch assembly (for rear LH door) connector.


b.

Measure the voltage according to the value(s) in the table below.

HINT:

Measure the values on the wire harness side with the connector disconnected.


Tester Connection Wiring Color Terminal Description Condition Specified Condition
M6-3 (B) - Body ground G - Body ground Power supply Power switch on (IG) 11 to 14 V

If the result is not as specified, there may be a malfunction in the wire harness.


c.

Reconnect the M6 power window regulator switch assembly (for rear LH door).


d.

Measure the voltage according to the value(s) in the table below.

Tester Connection Wiring Color Terminal Description Condition Specified Condition
M6-4 (U) - Body ground B - Body ground Power window motor UP output Power switch on (IG), rear LH door power window switch OFF → UP (Manual operation) Below 1 V → 11 to 14 V
M6-1 (D) - Body ground R - Body ground Power window motor DOWN output Power switch on (IG), rear LH door power window switch OFF → DOWN (Manual operation) Below 1 V → 11 to 14 V

If the result is not as specified, the power window regulator switch assembly (for rear LH door) may have a malfunction.



CHECK POWER WINDOW REGULATOR SWITCH ASSEMBLY (for Rear RH Door)


B164270
3.51,0.094 3.875,0.302 0.365,0.208 3.604,0.104 4.177,0.5 0.573,0.396 10 false L6

a.

Disconnect the L6 power window regulator switch assembly (for rear RH door) connector.


b.

Measure the voltage according to the value(s) in the table below.

HINT:

Measure the values on the wire harness side with the connector disconnected.


Tester Connection Wiring Color Terminal Description Condition Specified Condition
L6-3 (B) - Body ground G - Body ground Power supply Power switch on (IG) 11 to 14 V

If the result is not as specified, there may be a malfunction in the wire harness.


c.

Reconnect the L6 power window regulator switch assembly (for rear RH door) connector.


d.

Measure the voltage according to the value(s) in the table below.

Tester Connection Wiring Color Terminal Description Condition Specified Condition
L6-4 (U) - Body ground B - Body ground Power window motor UP output Power switch on (IG), rear RH door power window switch OFF → UP (Manual operation) Below 1 V → 11 to 14 V
L6-1 (D) - Body ground R - Body ground Power window motor DOWN output Power switch on (IG), rear RH door power window switch OFF → DOWN (Manual operation) Below 1 V → 11 to 14 V

If the result is not as specified, the power window regulator switch assembly (for rear RH door) may have a malfunction.



CHECK POWER WINDOW REGULATOR MOTOR ASSEMBLY (for Driver Door)


B280976
2.25,0.677 2.646,0.917 0.396,0.24 2.365,0.698 2.719,1.021 0.354,0.323 10 false J9

a.

Disconnect the J9 power window regulator motor assembly (for driver door) connector.


b.

Measure the voltage and resistance according to the value(s) in the table below.

HINT:

Measure the values on the wire harness side with the connector disconnected.


Tester Connection Wiring Color Terminal Description Condition Specified Condition
J9-1 (E) - Body ground W-B - Body ground Ground Always Below 1 Ω
J9-2 (B) - Body ground W - Body ground Power supply Power switch off 11 to 14 V

If the result is not as specified, there may be a malfunction in the wire harness.


c.

Reconnect the J9 power window regulator motor assembly (for driver door) connector.


d.

Measure the voltage according to the value(s) in the table below.

Tester Connection Wiring Color Terminal Description Condition Specified Condition
J9-4 (AUTO) - J9-1 (E) B - W-B Power window motor AUTO UP input Power switch on (IG), driver door power window fully open 11 to 14 V
J9-4 (AUTO) - J9-1 (E) B - W-B Power window motor AUTO UP input Power switch on (IG), driver door power window moving, power window regulator switch assembly fully pulled up (Automatic operation) Below 1 V
J9-4 (AUTO) - J9-1 (E) B - W-B Power window motor AUTO UP input Power switch on (IG), driver door power window fully closed 11 to 14 V
J9-4 (AUTO) - J9-1 (E) B - W-B Power window motor AUTO DOWN input Power switch on (IG), driver door power window fully closed 11 to 14 V
J9-4 (AUTO) - J9-1 (E) B - W-B Power window motor AUTO DOWN input Power switch on (IG), driver door power window moving, power window regulator switch assembly fully pushed down (Automatic operation) Below 1 V
J9-4 (AUTO) - J9-1 (E) B - W-B Power window motor AUTO DOWN input Power switch on (IG), driver door power window fully open 11 to 14 V
J9-5 (LED) - J9-1 (E) Y - W-B LED illumination signal Power switch on (IG) 11 to 14 V
J9-5 (LED) - J9-1 (E) Y - W-B LED illumination signal Approximately 43 seconds after power switch turned off Below 1 V
J9-7 (DWN1) - J9-1 (E) V - W-B Power window motor DOWN input Power switch on (IG), driver door power window regulator switch not pushed or pulled 11 to 14 V
J9-7 (DWN1) - J9-1 (E) V - W-B Power window motor DOWN input Power switch on (IG), driver door power window regulator switch pushed halfway down (Manual operation) Below 1 V
J9-7 (DWN1) - J9-1 (E) V - W-B Power window motor DOWN input Power switch on (IG), driver door power window fully closed 11 to 14 V
J9-7 (DWN1) - J9-1 (E) V - W-B Power window motor DOWN input Power switch on (IG), driver door power window regulator switch fully pushed down (Automatic position) Below 1 V
J9-7 (DWN1) - J9-1 (E) V - W-B Power window motor DOWN input Power switch on (IG), driver door power window fully open 11 to 14 V
J9-10 (UP1) - J9-1 (E) BE - W-B Power window motor UP input Power switch on (IG), driver door power window regulator switch not pushed or pulled 11 to 14 V
J9-10 (UP1) - J9-1 (E) BE - W-B Power window motor UP input Power switch on (IG), driver door power window regulator switch pulled halfway up (Manual operation) Below 1 V
J9-10 (UP1) - J9-1 (E) BE - W-B Power window motor UP input Power switch on (IG), driver door power window fully open 11 to 14 V
J9-10 (UP1) - J9-1 (E) BE - W-B Power window motor UP input Power switch on (IG), driver door power window regulator switch fully pulled up (Automatic operation) Below 1 V
J9-10 (UP1) - J9-1 (E) BE - W-B Power window motor UP input Power switch on (IG), driver door power window fully closed 11 to 14 V

If the result is not as specified, the power window regulator motor assembly (for driver door) may have a malfunction.



CHECK INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY AND MAIN BODY ECU (MULTIPLEX NETWORK BODY ECU)


a.

Disconnect the MB and I12 main body ECU (multiplex network body ECU) connector.

B278841
2.302,3.771 2.625,3.979 0.323,0.208 6.323,2.104 6.646,2.313 0.323,0.208 1.938,1.875 2.26,2.083 0.323,0.208 1.948,1.521 2.271,1.729 0.323,0.208 0.313,2.063 0.635,2.271 0.323,0.208 0.427,2.646 0.75,2.854 0.323,0.208 0.313,1.438 0.635,1.646 0.323,0.208 6.323,1.49 6.646,1.698 0.323,0.208 3.979,5.031 4.302,5.24 0.323,0.208 1.198,5.01 1.521,5.219 0.323,0.208 1.854,6.292 2.177,6.5 0.323,0.208 5.01,6.292 5.333,6.5 0.323,0.208 3.5,7.531 3.823,7.74 0.323,0.208 4.76,3.771 5.083,3.979 0.323,0.208 5.823,5.031 6.146,5.24 0.323,0.208 4.25,0.74 4.573,0.948 0.323,0.208 4.125,1.125 4.125,0.844 4.125,0.844 4.24,0.844 false 6.073,1.594 6.323,1.594 false 6.073,2.198 6.323,2.198 false 1.677,1.969 1.938,1.969 false 1.688,1.615 1.948,1.615 false 0.635,2.167 0.865,2.167 false 0.75,2.74 1.031,2.74 false 0.625,1.542 0.865,1.542 false 1.698,0.958 1.927,0.688 1.927,0.688 2.135,0.688 false 1.469,3.063 1.469,1.677 1.469,1.677 1.563,1.677 false 1.479,2.104 1.563,2.104 false 3.552,7.552 3.979,7.823 0.427,0.271 10 false MB 1.271,5.031 1.656,5.313 0.385,0.281 10 false 3C 1.938,6.313 2.375,6.646 0.438,0.333 10 false 3B 5.083,6.313 5.427,6.573 0.344,0.26 10 false 3A 4.052,5.052 4.365,5.385 0.313,0.333 10 false 3D 4.833,3.792 5.198,4.094 0.365,0.302 10 false I13 2.385,3.792 2.813,4.094 0.427,0.302 10 false I12 6.396,2.115 6.688,2.344 0.292,0.229 10 false 3A 2.01,1.896 2.417,2.188 0.406,0.292 10 false I12 2.021,1.542 2.438,1.813 0.417,0.271 10 false I13 0.385,2.083 0.781,2.375 0.396,0.292 10 false 3D 0.51,2.667 0.917,2.958 0.406,0.292 10 false 3F 0.385,1.458 0.74,1.708 0.354,0.25 10 false 3C 6.396,1.51 6.708,1.75 0.313,0.24 10 false 3B 5.917,5.052 6.25,5.354 0.333,0.302 10 false 3F 4.313,0.76 4.677,1.01 0.365,0.25 10 false MB 0.24,0.177 0.677,0.5 0.438,0.323 10 false *A 1.406,3.104 1.656,3.313 0.25,0.208 10 false *2 2.188,0.625 2.438,0.833 0.25,0.208 10 false *1
*A Main body ECU (multiplex network body ECU) (2 Connector Type) - -
*1 Main body ECU (multiplex network body ECU) *2 2 connectors


B282096
2.302,3.771 2.625,3.979 0.323,0.208 6.313,2.083 6.635,2.292 0.323,0.208 2.063,1.958 2.385,2.167 0.323,0.208 2.063,1.615 2.385,1.823 0.323,0.208 0.292,2.063 0.615,2.271 0.323,0.208 0.396,2.677 0.719,2.885 0.323,0.208 0.281,1.438 0.604,1.646 0.323,0.208 6.313,1.521 6.635,1.729 0.323,0.208 3.979,5.031 4.302,5.24 0.323,0.208 1.198,5.01 1.521,5.219 0.323,0.208 1.854,6.292 2.177,6.5 0.323,0.208 5.01,6.292 5.333,6.5 0.323,0.208 3.5,7.542 3.823,7.75 0.323,0.208 4.76,3.771 5.083,3.979 0.323,0.208 5.906,5.052 6.229,5.26 0.323,0.208 4.167,0.75 4.49,0.958 0.323,0.208 4.052,1.135 4.052,0.854 4.052,0.854 4.167,0.854 false 6.052,1.615 6.302,1.615 false 6.063,2.188 6.313,2.188 false 1.813,2.063 2.063,2.063 false 1.823,1.719 2.073,1.719 false 0.604,2.167 0.865,2.167 false 0.719,2.771 1.031,2.771 false 0.604,1.542 0.865,1.542 false 1.771,0.979 2,0.708 2,0.708 2.208,0.708 false 1.604,3.083 1.604,1.479 1.604,1.479 1.708,1.479 false 1.604,1.844 1.698,1.844 false 1.604,2.188 1.708,2.188 false 3.552,7.552 4.031,7.844 0.479,0.292 10 false MB 1.271,5.021 1.906,5.271 0.635,0.25 10 false 3C 1.938,6.313 2.51,6.667 0.573,0.354 10 false 3B 5.083,6.313 5.552,6.625 0.469,0.313 10 false 3A 4.052,5.052 4.615,5.365 0.563,0.313 10 false 3D 4.833,3.792 5.25,4.063 0.417,0.271 10 false I13 2.375,3.792 2.677,3.979 0.302,0.188 10 false I12 6.396,2.094 6.719,2.313 0.323,0.219 10 false 3A 2.135,1.969 2.583,2.25 0.448,0.281 10 false I12 2.135,1.635 2.5,1.865 0.365,0.229 10 false I13 0.385,2.083 0.865,2.385 0.479,0.302 10 false 3D 0.5,2.698 0.854,2.938 0.354,0.24 10 false 3F 0.354,1.458 0.833,1.74 0.479,0.281 10 false 3C 6.385,1.531 6.729,1.76 0.344,0.229 10 false 3B 5.99,5.073 6.302,5.333 0.313,0.26 10 false 3F 4.229,0.771 4.615,1 0.385,0.229 10 false MB 0.25,0.188 0.5,0.396 0.25,0.208 10 false *A 2.26,0.646 2.51,0.854 0.25,0.208 10 false *1 1.656,3.094 1.906,3.302 0.25,0.208 10 false *2
*A Main body ECU (multiplex network body ECU) (3 Connector Type) - -
*1 Main body ECU (multiplex network body ECU) *2 3 connectors



b.

Measure the voltage and resistance according to the value(s) in the table below.

HINT:

Measure the values on the wire harness side with the connectors disconnected.


Tester Connection Wiring Color Terminal Description Condition Specified Condition
MB-11 (GND1) - Body ground - Ground Always Below 1 Ω
MB-30 (BECU) - Body ground - Auxiliary battery power supply Power switch off 11 to 14 V
I12-3 (GND2) - Body ground W-B - Body ground Ground Always Below 1 Ω
MB-29 (ACC) - Body ground - ACC power supply Power switch on (ACC) 11 to 14 V
MB-29 (ACC) - Body ground - ACC power supply Power switch off Below 1 V
MB-31 (ALTB) - Body ground - Auxiliary battery power supply Power switch off 11 to 14 V
MB-32 (IG) - Body ground - Power switch power supply Power switch on (IG) 11 to 14 V
MB-32 (IG) - Body ground - Power switch power supply Power switch off Below 1 V

If the result is not as specified, there may be a malfunction in the wire harness.


c.

Reconnect the MB and I12 main body ECU (multiplex network body ECU) connector.


d.

Measure the voltage according to the value(s) in the table below.

Tester Connection Wiring Color Terminal Description Condition Specified Condition
3C-15 (FLCY) - Body ground L - Body ground Front door courtesy switch LH input Front door LH open Below 1 V
3C-15 (FLCY) - Body ground L - Body ground Front door courtesy switch LH input Front door LH closed Pulse generation
I13-19 (FRCY) - Body ground Y - Body ground Front door courtesy switch RH input Front door RH open Below 1 V
I13-19 (FRCY) - Body ground Y - Body ground Front door courtesy switch RH input Front door RH closed 11 to 14 V*1
Pulse generation*2
I13-11 (L2) - Body ground R - Body ground Driver door key-linked lock input Driver door key cylinder turned to lock Below 1 V
I13-11 (L2) - Body ground R - Body ground Driver door key-linked lock input Driver door key cylinder off 11 to 14 V
I13-24 (UL3) - Body ground Y - Body ground Driver door key-linked unlock input Driver door key cylinder turned to unlock Below 1 V
I13-24 (UL3) - Body ground Y - Body ground Driver door key-linked unlock input Driver door key cylinder off Pulse generation

*1: Main body ECU (multiplex network body ECU) (2 Connector Type)

*2: Main body ECU (multiplex network body ECU) (3 Connector Type)


If the result is not as specified, the main body ECU (multiplex network body ECU) or instrument panel junction block assembly may have a malfunction.



CHECK CERTIFICATION ECU (SMART KEY ECU ASSEMBLY) (w/ Smart Entry and Start System)


a.

Disconnect the I87 and I86 certification ECU (smart key ECU assembly) connector.

B278932
2.25,0.156 2.583,0.354 0.333,0.198 3.677,0.156 4.01,0.354 0.333,0.198 2.25,0.156 2.583,0.354 0.333,0.198 4.854,0.156 5.188,0.354 0.333,0.198 2.333,0.167 2.802,0.49 0.469,0.323 10 false O2 3.76,0.167 4.469,0.656 0.708,0.49 10 false I87 4.938,0.167 5.49,0.531 0.552,0.365 10 false I86


b.

Measure the voltage and resistance according to the value(s) in the table below.

HINT:

Measure the values on the wire harness side with the connector disconnected.


Tester Connection Wiring Color Terminal Description Condition Specified Condition
I87-5 (+B) - Body ground SB - Body ground Auxiliary battery power supply Power switch off 11 to 14 V
I86-1 (E) - Body ground W-B - Body ground Ground Always Below 1 Ω

If the result is not as specified, there may be a malfunction in the wire harness.


c.

Reconnect the I87 and I86 certification ECU (smart key ECU assembly) connector.


d.

Measure the voltage and check for pulses according to the value(s) in the table below.

Tester Connection Wiring Color Terminal Description Condition Specified Condition
I87-16 (IG) - Body ground LG - Body ground IG power supply Power switch off Below 1 V
I87-16 (IG) - Body ground LG - Body ground IG power supply Power switch on (IG) 11 to 14 V
O2-15 (RCO) - I86-1 (E) G - W-B Door control receiver power source
·

Power switch off

·

Transmitter switch not pressed


Below 1 V
O2-15 (RCO) - I86-1 (E) G - W-B Door control receiver power source
·

Power switch off

·

Lock or unlock transmitter switch pressed


4.5 to 5.5 V
O2-6 (RDAM) - I86-1 (E) Y - W-B Door control receiver data input signal Power switch off Pulse between 11 to 14 V occurs regularly

If the result is not as specified, the certification ECU (smart key ECU assembly) may have a malfunction.